Question about 1998 Pontiac Grand Am

1 Answer

Screw location on dash for 1998 pontaic grand am

Can you let me know the screw locations on 1998 grand am for dash removal

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Its 2 screws in the middle below the temp controls and 2 just above the speedometer.

Posted on Sep 04, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is computer located in 1998 pontiac grand am


The PCM on any Pontiac Grand Am is located behind the glove box. You must remove the screws attaching the glove box to physically see the PCM. Use caution if you're going to remove the glove box door. good-day !

Dec 06, 2011 | Pontiac Grand Am Cars & Trucks

1 Answer

Location of heater core on a 1998 pontiac grand prix gtp superchared


Heater cores in most vehicles are located in dash in front of passenger seat. Hard to get access to without taking dash out of car. They can usually be seen if you can get your head under the dash and look up on passenger side. May need to remove some small plastic molding and a few screws to see it.

Sep 28, 2011 | Cars & Trucks

1 Answer

Abs light stays on in dash. have been told this is a common problem with these models. where is brake control module located on 1998 plymouth grand voyager. 3.3. have been quoted $904 to fix. need...


Don't know how handy you may be but would seriously consider removing instrument cluster, and checking solder on circuit board. Just did mine, wasn't hard, maybe a couple of hours work. Nice small, pointed solder gun will be needed as well. They have had many weird problems with gauges, starting, running etc, all narrowed down to that printed circuit board, where the solder on the contact pins become corroded or cracked and cause some pretty weird stuff. At the very least, try removing dash enough to remove 4 screws holding cluster in, and pulling off connectors and putting them back on a couple of times, just in case it's just a dirty connection. If you decide you want to try it, and need more specific instructions, let me know, or even google , Dodge or Plymouth instrument cluster soldering, as there is some pictures and videos out there on the subject. Good Luck, and let me know how you make out.

Jan 29, 2011 | 1998 Plymouth Grand Voyager

1 Answer

1998 grand am ignition switch location, not tumbler just switch, gauge cluster went dead, not fuses


It's in the column screwed to the back side of the lock cylinder. It comes with a wire harness that goes down the column to the bottom of the dash.

Jul 17, 2010 | 1998 Pontiac Grand Am

1 Answer

How to remove onepice dash in a pontaic grand am


this is very time consumeing you need to strip the dash , radio buttons,etc then remove all screws then check for more screws until dash is removed there is even bolts under the dash above your feet

Aug 24, 2009 | 2004 Pontiac Grand Am

1 Answer

Where is the spark plug located in a 2005 pontaic grand am


Hello lilie39: My name is Roger and I will help you. Assuming you have a 2.2 4 Cly. engine in your car. You will find the spark plugs located in th middle of the cylinder head. You will need to remove the cover over the middle of the head to gain access to the plugs.
Please rate the quality of your answer. This way we know the answer you received was helpful. should you need further help please just ask. Thank You for using Fix Ya. Roger

Jul 15, 2009 | 2003 Pontiac Grand Am

1 Answer

How do you remove the dash board on a grand marquis 1996


It is best to remove the front seat then remove the outer trim work on the dash which are fastened with clips. Then remove the screws which hold the heater/AC controls and also the dash panel such as speedometer etc. Remove the lower plastic shield from around the steering column and disconnect the transmission gear position indicator cable. Remove the plastic covering between the steering column and the drivers knees. Their are mounting bolts in the dash and under neath as well and also barbed fasteners. Remove the steering wheel column mounting bolts and it's support brackets. Lower the steering column to the floor. Remove the front door coverings located near the door hinges. Be carefull not to break the fasteners. They pry out of the door weather stripping and then you lift up on them. This will give you access to the lower dash mounting brackets.
With the steering column lowered remove the plastic trim under the windshield. It pops out and givces you access to the front dash mounting screws. disconnest the headlight photo cell control, disconnect the clock, radio and all other pigtail connections that would otherwise interfear with removing the dash. I remove the speedometer electronic cluster as well. Disconnect the AC/heater upper and lower duct work. They are generally fastened with screws and and you have to look for them.
The dash is fastened by the previously mentiond screws located below the windshield and by bolts located near the door which can be seen when the trim is removed also by lower bracket that are braced and is easily identified. These bolts heads are # 10 metric. I have probably forgotten a couple of items but this should get you through the worse of it.
The Mercury Grand Marquis and the Crown Victoria both tend to have blend door problems for the climate control and the dash has to come out to access the blend door control.

Aug 02, 2008 | 1993 Mercury Grand Marquis

1 Answer

1998 jeep grand cherokee


Under the glove box beneath the dash the resistor should be screwed into the heater housing.

Jun 19, 2008 | 1998 Jeep Grand Cherokee

Not finding what you are looking for?
1998 Pontiac Grand Am Logo

Related Topics:

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...