Question about Nissan Maxima

1 Answer

Trying to remove the hub nut to replace wheel berings....nut wont budge at all

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 1,975 Answers

Your going to need power. I mean like an impact! It will come off though.

Posted on May 28, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove wheel hub


tractors in the automotive section..hmmmm lets see..the hub should have bolts holding the cover on..take them out carefully and remove the hub cover .. gear oil may run out at this point so either drain the axle or catch the oil in some sort of container..then there is a gear that needs removed..it supplies power from the drive axle to the wheel hub..once thats done there is a retaining ring or large nut that holds the wheel center on the axle..this retainer needs removed and the wheel should come off..some are hydraulically operated so there will be hoses to undo also..good luck..

Dec 15, 2013 | Cars & Trucks

1 Answer

Replace front right wheel bearing


This is a hub and bearing assy. You will need to remove the axle nut, brake rotor, caliper assy. There are 3 or 4 bolts that attach the hub assy to the knuckle assy. Most of the time, the hub assy will come out easy and sometime it comes out very hard. Make sure you torque the axle nut to the proper spec, so the bering will not fall apart and will last. Buy a quality hub and bearing assy, so you dont have to do it again.

Nov 03, 2013 | 1995 Oldsmobile Aurora

1 Answer

Hi, i want to change the rear brake shoes on a 95 toyota granvia , is the hub nut left hand or right hand thread as it wont budge, thanx.


That nut is a locking nut and requires you to remove a locking washer from the hub itself, I use a flat head screw driver and a rubber mallet ( tapping with a medium strength) to free it up this usually needs to be replaced.

Jul 12, 2011 | Toyota Passenger Cars & Trucks

1 Answer

How hard is it to change the front wheel berings and what tools are needed? Then how is it done?


first im amazed it needs bearings. raise the front end and remove the wheel. undo the big nut in the center of the hub. undo the abs plug . on the back of the hub is 3 bolts remove these and using a press or rubber mallet push the cv axle in. it should pull the hub out as you do it. replace with a new hub assembly and your good to go. make sure to rehook the abs plug and clip it to the holes were the old was clipped. heres a couple pictures to help guide you. hope this helpsonetufshoppe_69.gifonetufshoppe_68.gif

Jan 28, 2011 | 2008 Chevrolet Uplander

3 Answers

2005 equinox wheel bearing assy wont come out


okay i assume the rotor is off,remove the bolts out the back, take a hammer and beat the front of the hub the top then bottom then the sides to free,hit so that hub pull out,you will be hitting the back side the hub where the wheel would sit,if that doesnt work then use a chisel to break free, stick it where the hub meet spindle,ITs just frozen beat it.a56579d.jpg

May 15, 2010 | 2005 Chevrolet Equinox

1 Answer

Trying to remove the inner rear wheel on my dually-diesel. Never had to before. Removed the inner bolts, won't budge. Is there anything else to "remove" or do I just start beating it with a mallet?


yes these are now on a "pilot hub" and any dust/dirt will make them seize,wet them down and carefully beat the inner wheel loose,after removal though do not use any "anti-seize" compound on anything when replacing the dual assembly,but a little grease on the outer nut/washer combo so the washer spins freely of the cap nut is recommended

May 15, 2010 | 1988 Ford F 350

1 Answer

Front wheel berings 2003 silverrado 1500 4 wheel drive describe procedure to change out


reomve tire securing the vehicle with tire hanging at it's lowest possition, remove the brake caliper & brake disc , remove nut lock on axle also axle nut , mark and remove strut bolts and push strut out remove ball joint lower bolt and use a fork ( tooling) seperate from hub slide hub off of axle , reverse steps to replace .

Aug 22, 2009 | 2003 Chevrolet Silverado 2500HD

1 Answer

How to replace front rotors


You'll need to take the wheel bearings off. the rotors are bolted to the hub and the bolts are located in the back of the hub thus having to remove the wheel bearings and removed the hub/rotor assy.

Apr 26, 2009 | Nissan Frontier Cars & Trucks

1 Answer

Replace rotor


when you take the front wheels off you will see a silver center cap in the middle of the hub take a flat heat screw driver a gently pry the cap off (don't worry if you mame it alittle) there will be a cotter pin a nut and a washer then you outter bering take them all off then the rotor will come off the inner bering is still in the rotor being held by the grease seal pry the old grease seal off and remove the bering. check berings for wear like ruff spots. make sure you buy a new grease seal for the rotor. reverse removal procedure re pack berings with fresh grease inner first place bering in the rotor put seal in place will need to tap it in carefully when putting the nut back on tighten untill snug not tight check for specs if you want i usually make it snug then 1 more turn do not over tighten and you will be good

Apr 07, 2009 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...