Question about Nissan Versa

Open Question

How do you remove the rear seat from a 2010 nissan versa sedan?

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2187 Answers

SOURCE: My trunk lock does not

You would need to pop the rear cushions out. Unbolt the 2 11mm bolts which holds the seat then lift the seat back up. Lastly, push the plastic divider out of the way.

Posted on Jun 05, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2011 Nissan Versa sedan trunk locked and will not open with key. Advice?


Most cars have a cable and lever to open it by the driver's seat, will that open it for you?

Dec 14, 2016 | 2011 Nissan Versa

1 Answer

Will a 2014 nissan versa sedan fit on a 2015 nissan versa sedan


Probably have to make minor adjustments but it shouldn't be to bad of a problem

Oct 06, 2015 | Nissan Cars & Trucks

1 Answer

How do find the transmission fluid level on a Nissan Versa?


Here's a diagram for the transmission fluid on the 2010 model.

25893075-onzbdthlkhwu0gpquek0abow-4-0.jpg See how numbers 1 and 2 vary for automatic or manual transmissions?

This is page 6 from section 8 of the owners manual found at:
http://www.nissanusa.com/pdf/techpubs/versa/2010/2010-Nissan-Versa.pdf

Oct 04, 2015 | 2009 Nissan Versa

2 Answers

2010 Nissan Versa. Key won't go to lock, so can't remove.


I would say its not all the way into park.

Jun 15, 2012 | 2010 Nissan Versa

1 Answer

Change fuel pump


you can get at the fuel pump by removing the rear seat.. so remove that and look .. I wouldnt use a trouble if i were you.. remove rear seat and see what else you need to remove..and dont spill!! Gas is expensive!!

Apr 18, 2012 | 2011 Nissan Versa 1.8

1 Answer

How to remove bottom section of rear seat in 2010 Nissan Navara D40 ST Dual Cab to fit saet cover


there should be a couple of bolts one on each side on the floor in front of the seat bottom remove and get in car put your hands down between the top and bottom seats and lift hard

Feb 26, 2011 | Nissan Titan Cars & Trucks

3 Answers

How do i take the back off on a 1999 nissan maxima bucket seat


Hi, follow the instruction below......
Rear
See Figures 3, 4, 5 and 6
  1. Remove the lower seat cushion by pulling straight up on the front portion and disengaging the clips. Then hinge the seat upward to release the rear clips.
03b6e0a.jpg

Fig. 3: Pull up on the front of the lower seat cushion and disengage the clips
  1. Remove upper rear seat back-to-chassis bolts.
77eb191.jpg

Fig. 4: Remove the bolts behind the center armrest ...

a796228.jpg

Fig. 5: ... and the bolts on the lower corners ...

fbf100a.jpg

Fig. 6: ... Then pull up on the seat to disengage the three clips on the top of the seat
  1. Remove rear seat back by tilting forward and pulling straight up.

To install:
  1. Install the lower seat cushion and torque the lower rear seat-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm).
  2. Install the upper rear seat back cushion and torque the upper rear seat back-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm)

Jan 19, 2011 | 1999 Nissan Maxima

1 Answer

I need to remove the backseat of my Nissan Maxima-2007 3.5SE..I dropped a small ring down the back of the leather seat..I have tried to use a vaccum , no luck..


Typically, seats jamb fit at the rear and have a spring piece that engauges at the front. To realease, the seat gets moved rearward about 1/2 inch and then pulls up in the front.... Compress the rear of the seat and it takes kind of a lot of force to move the entire seat rearward, but that is what you do....

Sep 20, 2009 | 2007 Nissan Maxima 3.5 Sl Sedan

1 Answer

I need to replace a rear seat belt in a 1997 Ford Tarsus. Does any know the best way to access the assembly? In addition, are there any diagrams available that show the connection points?


please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

Removal
  1. Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear Sedan
Removal
  1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
  1. Remove rear seat cushion from vehicle.
  1. Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear 60/40 Split Bench—Sedan
Removal
  1. NOTE: Safety belt bolts do not secure seat back to vehicle.

    Remove rear seat cushion as described.
  1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
  1. Remove two bolts from outboard rear seat back frame retaining brackets.
  1. Lift seat back up and pull forward to remove from vehicle.
  1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan Removal
  1. Remove rear seat. Refer to Section 01-10 .
  1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
  1. Pull lower quarter trim panel away from body.
  1. Remove safety belt retaining bolt.
  1. Feed safety belt through lower quarter trim panel.
  1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
  1. Remove retractor anchor nut and retractor from rear quarter panel.
  1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
  1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
  1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.


    2a6fac0.gif


    Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)
  1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.


    fff90b0.gif

Installation
  1. To install, reverse Removal procedure.
  1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
  1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
  1. Check the restraint system for proper operation.

Jun 30, 2009 | 1997 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...