Question about 1995 Ford Ranger Supercab

1 Answer

I have no spark from the coil. The ignition module, coil and distributor all check out ok.1985 Ranger, 2.3 L engine with fuel injection.

Posted by on

1 Answer

Have you checked the clutch switch? there is a switch attached to the clutch that doesnt allow your truck to turn on if the clutch isnt pushed in.

Posted on Aug 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Does an ignition control module have anything to do with fuel pump functioning?


1987 rangers use a device called a TFI module to control ign. timing , this merely triggers a std. coil to fire the center port of distributor cap , this device only controls the coil to fire but does send a pulse for timing back to ecu this sets the base pulse for fuel injection , but its also affected by manifold Air flow and exhaust O2 amounts (closed loop) , but engine should run in base mode (open loop) fuel timing (but not well) , fuel pump relay is enabled to run via ECU output , Now your year ranger had a tech bulletin out on fuel pumps , seems they had a problem getting them to work after a fuel filter was replaced , something about a false backpressure , no if you have no/low fuel pressure then id look at fuel pump power 1st then fuel pump itself assuming you've already tried a new filter of course

Jun 14, 2015 | 1987 Ford Ranger

3 Answers

Engine stop


If theres no spark from the spark plugs then you would have to replace them?

Jul 12, 2008 | 1993 Toyota Corolla

1 Answer

I have a 1988 ranger no spark no fuel pressure iv replace the coil what could the issue be


Is it Fuel injection and electronic ignition, or still distributor and carb?
if its FI, check the fuel relay, located in the fuse box usually, not sure where for your truck specifically, but if you locate it, tap on it a few times while someone else cranks the truck, also, the fuel pump could be faulty, can you hear the winding noise when you turn on the ignition, if not, then pump is gone.
The spark issue is a tricky one since you said you have replaced the coil... spark wires ok? coil installed properly? battery charged and leads tight? alternator working? if alternator is failing to charge the battery, then it gets to a point where you dont have enough power to make the coil spark, the engine will crank, but not enough current (amps) to fully charge coils to deliver healthy spark.

Good luck...

Aug 19, 2011 | 1988 Ford Ranger

2 Answers

No spark


There's no emergence switch, if there was it would only be for fuel and not spark, there four thing to get spark,
ignition control module, ignition coil, distributor pick up assembly and spark plug wire's check for spark at coil, more then likely it's going to be your distributor pick up assembly, the pick up sit in side your ignition distributor, replace it and it will start, hope this was very helpful.

May 19, 2010 | 1985 Ford F 250

1 Answer

Stalled and will not start. Getting fuel, no


I would suspect the ignition module or the distributor itself is malfunctioning. Also check the ignition rotor and make sure that it is not burned through.

Apr 19, 2010 | 1985 Toyota Pickup

2 Answers

Changed coil and distributor cap, still my engine has no spark


Here are 2 things to check. With the distributor cap off crank the engine. Does the rotor turn? If it's not turning you may have a broken timing chain. If your timing chain is ok then the problem may be the ignition module. This is usually located at the base of the distributor and it will have several wires running into it. The ignition module converts the DC battery voltage into an AC voltage that the ignition coil transforms up to a much higher voltage that will be sent out to the spark plugs through the distributor. I hope this helps you out.

Feb 22, 2010 | BMW 535 Cars & Trucks

1 Answer

Car just stopped running. Lost power suddenly.


Find an inductive pickup indicator for spark. Place on distributor cap to see if spark is at coil internal tower. If no spark at internal tower, look at ignition module or pickup coil. Ignition modules are prone to failure on 626's. But if you have spark at tower but not at the wire end, then your rotor is gone.

Aug 18, 2009 | 1993 Mazda 626

2 Answers

94 Aerostar won't start. No fire


1 Inspect Battery Damaged or faulty battery and/or connections. here is a list of things u can check hope this helps Shaun 2 Inspect Coil - Ignition Damaged or faulty ignition coil or ignition coil circuit. grey_line.gif 3 Inspect Fuel Filter Clogged or dirty fuel filter grey_line.gif 4 Inspect Fuel Injector Pressure Regulator Faulty fuel injector pressure regulator or circuit. grey_line.gif 5 Inspect Fuel Pump Improperly functioning fuel pump or circuits. grey_line.gif 6 Inspect Wireset Damaged, worn, or deteriorating spark plug or coil wire(s). grey_line.gif 7 Inspect Control Module-Ignition Faulty ignition control module or circuit. grey_line.gif 8 Inspect Solenoid Switch Damaged or faulty solenoid switch or solenoid switch circuit. grey_line.gif 9 Inspect Starter Damaged, worn, defective, or faulty starter or starter related circuit. grey_line.gif 10 Inspect Neutral Safety Switch Damaged or faulty neutral safety swittch or circuit. grey_line.gif 11 Inspect Fuse Corroded, burned, or shorted fuse may be interupting power source. grey_line.gif 12 Inspect Fusible Link Corroded, burned, or shorted fusible link may be interupting power source. grey_line.gif 13 Inspect Battery Cable Corroded, broken or poorly connected battery cable. grey_line.gif 14 Inspect Spark Plug Wire Loom - Performance Improperly adjusted or worn/malfunctioning carburetor. grey_line.gif 15 Inspect Distributor Cap Loose or cracked distributor cap grey_line.gif 16 Inspect Distributor Cap And Rotor Kit Loose, cracked, or worn distributor cap and ignition rotor. grey_line.gif 17 Inspect Fuel System Pressure Incorrect fuel pressure being delivered to carburetor or fuel injection system. grey_line.gif 18 Inspect Fuel Injector Plugged, dirty or poorly connected fuel injector. grey_line.gif 19 Inspect Ignition Switch Worn, damaged or faulty ignition switch or circuit. grey_line.gif 20 Inspect Spark Plug Fouled, damaged or broken spark plug(s). grey_line.gif 21 Inspect Belt Incorrectly routed, adjusted(tensioned), missing or worn drive belt(s). grey_line.gif 22 Inspect Timing Belt Slipped or broken timing belt. grey_line.gif 23 Inspect Timing Set Slipped timing chain or worn timing gear(s). grey_line.gif 24 Inspect Fuel Tank Contaminated fuel from rusted or deteriorated fuel tank. grey_line.gif 25 Inspect Ignition Timing Incorrectly adjusted engine timing. grey_line.gif

Nov 23, 2008 | 1994 Ford Aerostar Extended

1 Answer

85 ford ranger 2.8 v6


Try replacing the ignition module in the distributor. This is a common problem on these engines.

Jun 16, 2008 | 1985 Ford Ranger

Not finding what you are looking for?
1995 Ford Ranger Supercab Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...