Question about Dodge Neon

1 Answer

What is the camshaft pulley bolt torque for a 2000 dodge neon 2 litre single cam

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 701 Answers

Hello mudpie67: My name is Roger and I will help with your question. The correct torque value for the camshaft gear is 115(n.m) or 85 (ft.lbs.) Should You need further help? Please just ask. Please rate the answer. Thank You for using Fix Ya. Roger

Posted on May 28, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need torque spec. For camshaft pulley bolt on 2004 dodge stratus


2004 dodge stratus 2.7 L v6 200i--2006 engine identification is EER has twin cam shafts and the bolts that hold the sprockets to the cam shaft are at 21 ft/lbs
there are 4 bolts for each cam (autodata publication page 375)
if this is not your engine then comment as to how many cam shafts it has as there are many different settings for different dodge engines

Oct 26, 2015 | Dodge Cars & Trucks

1 Answer

Torque specifications


Head bolts are torqued in 3 steps, 1-18ft.lbs, 2-60 degrees, 3-60 degrees, camshaft caps-10-11 ftlbs, intake manifold-12-17ftlbs, exh manifolds-32-40 ftlbs, camshaft pulley-74-89 ftlbs.

Feb 05, 2014 | Cars & Trucks

2 Answers

Need timing gear marks for 2004 Kia Sadona 3.5L engine



Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Record the radio anti theft code data.
  3. Remove or disconnect the following:

    Negative battery cable Engine cover Accessory drive belts Idler pulley Crankshaft pulley Power steering pump pulley Belt tensioner pulley Upper and lower timing belt covers
  4. Support the engine with a floor jack and remove the engine mount.
  5. Rotate the engine to align the camshaft sprocket timing marks with the cylinder head cover timing marks.

    0996b43f8022cb71.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt routing and timing marks-3.5L Engine

  6. Remove or disconnect the following:

    Auto tensioner Timing belt

    0996b43f8022cb72.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt and related components-3.5L Engine


To install:
  1. Ensure that the engine is set to Top Dead Center (TDC).
  2. Prepare the auto tensioner for installation by compressing it in a vise and installing a retaining pin.
  3. Install the timing belt in the following order:
    1. Crankshaft sprocket
    2. Idler pulley
    3. Left bank exhaust camshaft sprocket
    4. Left bank intake camshaft sprocket
    5. Water pump pulley
    6. Right bank intake camshaft sprocket
    7. Right bank exhaust camshaft sprocket
    8. Tensioner pulley

  4. Install the auto tensioner. Do not remove the retaining pin at this time.
  5. Check that the crankshaft and camshaft timing marks are aligned correctly.
  6. Rotate the crankshaft 1 / 4 turn Counterclockwise .
  7. Rotate the crankshaft 1 / 4 turn Clockwise to return the engine to TDC.
  8. Loosen the tensioner pulley center bolt.
  9. Apply 44 inch lbs. (5 Nm) torque to the tensioner pulley as shown and tighten the center bolt to 32-41 ft. lbs. (43-55 Nm).

    0996b43f8022cb73.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Adjusting the tensioner pulley-3.5L Engine

  10. Remove the auto tensioner retaining pin.
  11. Rotate the crankshaft 2 revolutions Clockwise , then wait 5 minutes for the auto tensioner to adjust.
  12. Measure the auto tensioner rod as shown. If the measurement is not 3.8-4.5 mm, then repeat the belt tensioning procedure.

    0996b43f8022cb74.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Measuring the auto tensioner rod-3.5L Engine

  13. When the auto tensioner measurement is correct, install or connect the following:

    Engine mount Upper and lower timing belt covers Belt tensioner pulley Power steering pump pulley Crankshaft pulley Idler pulley Accessory drive belts Engine cover Negative battery cable
  14. Reprogram the radio anti theft codes.

    Kia_Sedona_2002-2006
    Timing Chain, Sprockets, Front Cover & Seal

    Print


    Removal & Installation

    3.8L Engine

    1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
    2. Record the radio anti theft code data.
    3. Remove the engine from the vehicle.
    4. Remove the drive belt. Remove the power steering pump. Remove the air conditioning compressor.
    5. Remove the alternator. Remove the drive belt idler. Remove the drive belt tensioner. Remove the water pump pulley. Remove the intake manifold.
    6. Remove the connector bracket from the left cylinder head cover. Disconnect the right ignition coil connector, condenser connector and remove the bracket.
    7. Remove the left cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    8. Remove the right cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    9. Set the No. 1 cylinder to TDC on the compression stroke. Turn the crankshaft pulley and align its groove with the timing mark T of the lower timing chain cover.
    10. Check that the mark of the camshaft timing sprockets are in straight line positioning on the cylinder head surface. If not rotate the crankshaft 360 degrees. Do not rotate the engine counterclockwise.
    11. Remove the oil pan. Remove the crankshaft damper pulley. Remove the timing chain cover.
      NOTE Be careful not to damage the contact surfaces of the cylinder block, cylinder head and timing chain cover. Before removing the timing chain, mark the right and left timing chains with an identification mark based on the location of the sprocket because the identification mark on the chain for TDC can be erased.
    12. After compressing the timing chain tensioner, install a set pin. Remove the right cam to cam guide. Remove the right timing chain auto tensioner and timing chain tensioner arm.
    13. Remove the oil pump chain cover. Remove the oil pump chain tensioner assembly. Remove the oil pump chain guide. Remove the right timing chain.
    14. Remove the right timing chain guide. Remove the oil pump chain sprocket and oil pump chain. Remove the crankshaft sprocket, oil pump and camshaft drive gear.
    15. Remove the left cam to cam guide. Remove the left timing chain auto tensioner and timing chain tensioner arm. Remove the left timing chain.
    16. Remove the left timing chain guide. Remove the crankshaft sprocket and left camshaft drive. Remove the tensioner adapter assembly.

      0996b43f8020193b.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing chain and related components-3.8L Engine


    To install:
    1. Check the camshaft and crankshaft sprockets for wear and damage, replace as required.
    2. Inspect the tensioner arm and chain guide for wear and damage, replace as required.
    3. Check that the tensioner pin moves smoothly when the ratchet pawl is released with a thin rod.
    4. The key of the crankshaft should be aligned with the timing mark of the timing chain cover. This indicates that the piston is at TDC on the compression stroke.
    5. Install the tensioner adapter assembly. Install the crankshaft sprocket and left camshaft drive.
    6. Install the left timing chain guide and torque the retaining bolts 14-18 ft. lbs.
    7. Install the left timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, timing chain guide, exhaust camshaft sprocket, intake camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201924.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Left timing chain markings and installation: (D) exhaust camshaft sprocket (C) intake camshaft sprocket-3.8L Engine

    8. Install the left timing chain tensioner arm and torque the retaining bolts 14-16 ft. lbs.
    9. Install the left timing chain tensioner and torque the retaining bolts 7-9 ft. lbs.
    10. Install the left cam to cam guide and torque the retaining bolts 7-9 ft. lbs.
    11. Install the crankshaft sprocket, oil pump and right camshaft drive.
    12. Install the oil pump chain and oil pump sprocket. Torque the retaining bolt to 14-16 ft. lbs.
    13. Install the right timing chain guide. Torque the retaining bolts to 14-18 ft. lbs.
    14. Install the right timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, intake camshaft sprocket, exhaust camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201925.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Right timing chain markings and installation: (C) exhaust camshaft sprocket (B) intake camshaft sprocket-3.8L Engine

    15. Install the right timing chain tensioner arm. Torque the retaining bolts to 14-17 ft. lbs.
    16. Install the right timing chain auto tensioner. Torque the retaining bolts to 7-9 ft. lbs.
    17. Install the right cam to cam guide and torque the retaining bolts to 7-9 ft. lbs.
    18. Install the oil pump chain guide. Torque the retaining bolts to 7-9 ft. lbs.
    19. Install the oil pump tensioner assembly. Torque the retaining bolts to 7-9 ft. lbs.
    20. Pull out the pins on both the left and right hydraulic tensioners. Install the oil pump chain cover.
    21. Rotate the crankshaft two revolutions in the clockwise direction. Confirm the timing mark. Be sure to rotate the crankshaft in the clockwise direction.
    22. Apply sealant on the chain cover and on the cylinder head, cylinder block, and lower oil pan. Be sure these parts are free of engine oil and dirt.
      NOTE Before assembling the timing chain cover, the liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201926.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Sealant application (1 inch bead width)-3.8L Engine

    23. Apply sealant on the chain cover.
      NOTE The liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201927.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover sealant application-3.8L Engine

    24. Install a new gasket to the timing case cover.
      NOTE It is important that the dowel pins on the cylinder block and holes on the timing chain cover should be used as a reference in order to assemble the timing chain cover in the correct position.


      0996b43f80201928.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover gasket installation (A) gaskets-3.8L Engine

    25. Install the timing chain cover. Torque the retaining bolts in the proper sequence and to specification. The engine should not be started for at least thirty minutes after timing chain cover assembly.

      0996b43f80201929.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover bolt torque sequence and specification-3.8L Engine

    26. Install the timing case cover oil seal.
    27. Continue the installation in the reverse order of the removal procedure.

May 19, 2012 | 2004 Kia Sedona

1 Answer

Seat inca van 00 sdi 1.9 diesel.. tension polly came loose.. timing belt slipped.. I need to know how to reset it again. Where are the markings on the crank shaft and the cam shaft? Please attach any...


Timing belt set-up for a 2000 Seat Inca 1.9 SDi

1. Align the crankshaft timing marks on the flywheel / gearbox

tdisline_583.jpg
2. Remove the valve cover
3. Lock the camshaft

tdisline_584.jpg
4. Fit the injection pump locking pin

tdisline_585.jpg

5. Loosen the camshaft gearwheel bolt, 180 degrees. Use a wrench to counter-hold
6. Loosen the camshaft gearwheel while holding it in place

tdisline_586.jpg

7. Fit the timing belt in the sequence as shown in the below figure: a - b - c - d - e - f - g

tdisline_587.jpg

8. Fit the timing belt and camshaft gearwheel together
9. Turn the tensioner clockwise to align both marks

tdisline_588.jpg

10. Tighten the large bolt on the tensioner to a torque of 20 Nm
11. Check for correct fit
12. Lock the camshaft. Tighten the camshaft gearwheel bolts: 45 Nm. Use a wrench to counter-hold
13. Remove helping tools
14. Turn the engine two rotations by hand
15. Repeat the procedure if required
16. Fit the vacuum pump
17. Refit the crankshaft pulley. Tighten torque: 20 Nm + 20 degrees
18. Fit the timing belt cover
19. Refit the valve cover
20. Fit the ancillary drive belt
21. Refit the inlet air manifold hoses
22. Check the injection timing

Torque settings:
Camshaft gearwheel: 45 Nm
Tensioner pulley: 20 Nm
Crankshaft pulley: 20 Nm + 20 degrees

May 26, 2011 | Volkswagen Passat Cars & Trucks

1 Answer

What are the camshaft torque specs on a 1997 dodge neon 2.0 litre dohc


camshafts do not have a torque setting

camshaft towers do if that is what you mean

Feb 27, 2011 | 1997 Dodge Neon

1 Answer

Timing Chain Replacement procedure steps


1. Jack up front of vehicle and support on safety stands. Remove left front wheel.
2. Remove alternator/water pump drive belt. Remove water pump pulley.
3. Remove A/C belt if equipped.
4. Remove valve cover.
5. Remove upper timing belt cover.
6. Rotate crankshaft until No. 1 cylinder is at TDC compression stroke and camshaft sprocket timing marks align with edge of cylinder head. "UP" cast on sprocket will be at top when sprocket is in correct position. Crankshaft may be rotated using a socket wrench inserted through access hole in left fender well (engine rotates counterclockwise).
7. Unbolt and remove crank pulley. Remove rubber seal washers from belt tensioner pivot and adjustment bolts protruding through lower belt cover. Remove belt cover retaining bolts and remove cover from below.
8. Remove concave belt retainer from end of crankshaft. If timing belt is to be reused, mark direction of rotation before removing.
9. Loosen belt tensioner pivot and adjustment bolts. Push tensioner away from belt and retighten adjustment bolt to hold tensioner in this position. Remove belt.
10. Insert a suitable tool through cam sprocket and brace against cylinder head. Remove bolt and pull sprocket from camshaft.
11. Without dislodging key, install new sprocket on camshaft. Torque bolt to 22 ftlb (30 Nm).
12. Install new timing belt by starting at crank gear and working it over cam sprocket in clockwise direction. Ensure that timing marks are properly aligned.
13. Release tensioner by loosening adjustment bolt. After tensioner contacts belt, retighten bolt.
14. Rotate engine at least one full turn (counterclockwise) and check that timing marks are aligned. Loosen adjustment bolt and allow tensioner to take out any remaining belt slack. Torque adjustment and pivot bolts to 22 ftlb (30 Nm).
15. Install remaining components in reverse order of removal. Torque fasteners to following values:

TORQUE VALUES

Valve Cover Nuts - 7 ftlb (10 Nm)
Cam Sprocket Bolt - 22 ftlb (30 Nm)
Tensioner Pivot Bolt - 22 ftlb (30 Nm)
Tensioner Adjust Bolt - 22 ftlb (30 Nm)
Belt Cover Bolts - 7 ftlb (10 Nm)
Crank Pulley Bolt - 83 ftlb (115 Nm)
Water Pump Pulley Bolts - 9 ftlb (12 Nm)

daves944_3.jpg

Dec 19, 2010 | 1983 Honda Accord

1 Answer

2002 escape 3.0 camshaft cap bolt torque specifications


make sure to apply 5w-20 oil to caps prior to install. Also caps and journals are number so you do not install in wrong place. Starting with Righ side looking at pulleys from front, right side cam start with first cap on left being #1 then bolt on other side of cap as #2. Cap behind would be #3 to left then #4 bolt next to it. Keep tightening the next 2 caps behind them in same manner, then jump to front of cam to left side and tighten caps front to back. You should tighten to 10 Nm (89 lbs-in) with a torque wrench. Then you tighten left side head cam caps starting with the left side if looking at front pulleys. Start at front caps working to rear then jump to right side cam front to back. Tighten these caps at 8 nm (71 lb-in) using torque wrench. Also make sure if heads are bolted to block that cam pulley postion is the following: left side looking at pulleys------left pulley mark at 12 o'clock right pulley mark at 3 o'clock. Right side head looking at pulleys------- left side pulley at 9 o'clock and right side pulley at 12 o'clock. When I say clock postion that means using head where valve covers meet as your straight vertical postion.

May 05, 2010 | 2002 Ford Escape

1 Answer

Where is the camshaft sensor on a 2004 dodge neon sxt engine and how do i change it


disconnect the negative battery cable. the cmp sensor is located on the left end of the cylinder head. move thebrake booster hose and electrical wires out of the way to access the cmp sensor. disconnect the sensor plug by pushing the locking tab back toward the firewall. remove the 4 bolts from sensor and lift out sensor. remove the trox bolt which holds the target magnet to camshaft. when installing target magnet be sure to line up holes to dowels on end of camshaft. torque torx bolt to 30 in-lbs. be sure to install new o-ring on sensor and torque bolts to 80 in-lbs. (hallclifford)

Apr 08, 2010 | 2004 Dodge Neon

1 Answer

Looking for tourc specs on 2.0 liter 1998 dodge neon


i need head,intake,exhaust,camshaft and pulley torque specs for a 2.0 dohc plus a timing belt positioning diagram

Jun 14, 2009 | 1998 Dodge Neon

1 Answer

Camshaft Position Sensor


On the drivers side of the head. Should be a 2 or 4 bolt sensor, with the plug at the bottom. Not a whole lot of room to get to it, but fairly easy.

Jun 02, 2009 | 2000 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

437 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...