Question about Peugeot Liberte

Open Question

Remove exterior door handle on peugeot 206 lx

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 58 Answers

SOURCE: 2000 ford explorer door handle

I assume you mean the drivers door. You need to remove the door panel and there are two nuts on the inside holding it on.The door panel has three retaining screws and you need to locate and remove. You then slide the door panel up and then remove it.DON'T pry the panel out you will break it.One screw is on the bottom of the panel. You should see that one. The other ones are under the door switch area and the inside door handle trim.Some have one under the remote mirror trim but not likely.That should give you access to the door handle nuts. Good Luck and I hope this helps you. Thanks Dan

Posted on Jun 21, 2008

Ad
  • 43 Answers

SOURCE: Need to know how to install exterior door handles

I'm assuming that you have the coupe not convertible since I've had same problem with my 97 Dodge Avenger and this is quite common from what I have heard. The handle is held in place by two 10mm bolts. One is easily accessable, located right beside the handle with the door open. The other is a little harder to get at. The first thing you need to do is remove the inside door cover, held in place by four screws and push in clips along the bottom that pull out easily. Two of the screws are visible and in the top corners of the door panel. One screw is located behind the inside handle and once removed the moulding comes off quite easily. The other screw is in the hand hold where you pull the door closed and has a small plastic cover over it. If you have power windows you are able to disconnect the switches once the panel is off. If manual windows, the handles are usually held on by a clip that can be pushed off with a screw driver allowing you to pull of the crank handle. The window needs to be in the closed position so you can access the ONE 10mm bolt holding the outer door handle. Once the interior door panel is off, if any clips remain in the door, take them out and put them where they should be in the door cover it won't go back together properly if you don't. Now you'll need to pull down the corner of the plastic covering the door, don't remove all the plastic just enough to allow access to the bolt. I used a small rachet to get it out. It is in a stupid spot with not much room but is doable. Once out, the handle is only being held by the lock rods to the handle and lock cylinder. The lock cylinder is held by a retaining clip which can be slid off allowing the cylinder to be pushed out. The other rod connected to the handle has a plastic clip on it holding it in place. This can be opened with a small screwdriver. Once opened the rod will come out easily and the handle should come off the door. The only problem reinstalling, that I had, was reconnecting the rod to the handle and found that if you unscrew the door latch, the whole mechanism can be moved down, giving you more freedom to work with the rod. You might want to do this before fighting with the clip holding the rod in place, just a thought as I got mine apart in 20 min. Installing the new handle is quite easy, just attach rod to the handle FIRST before anything else. Once the handle is back on the door the lock cylinder can be pushed back in, it just gets in the way if you put it in the handle right away. Hope this is of some help.

Posted on Oct 05, 2008

  • 112 Answers

SOURCE: 2002 Nissan Altima Exterior Door Handle

Look at the inside of the door directly behind the door handle. There should be a hole about 15 mm wide.
Just enough to get a small socket through.
Make sure the window is up.

Posted on Feb 03, 2009

wireguy212
  • 1627 Answers

SOURCE: replacement exterior door handle

you will need to get the door panel off the inside,undo the linkages and the remove the nuts holding the handle on.

Posted on Jul 28, 2009

  • 1 Answer

SOURCE: 2002 Nissan Altima Exterior Door Handle

I seriously doubt that supergluing or even epoxying a handle back will hold at all, or hold for more then few days.
I would only suggest doing the replacement yourself if you familiar with this type of work, or has the aptitude to figure out how to do it, and have the right tools because it is NOT trivial and a number of things can be done wrong, broken or scratched.
The handle itself cannot be replaced. The outside door handle assembly (which includes the handle, the bezel with all associated springs, plastic and metal hardware) has to be replaced. Besides junkyards, which is a long shot for number of reasons, the only place where the handle assembly can be bought is the dealer. And these handle assemblies are not cheap ether. The driver side handle on my 2002 Altima broke first. I paid $60.23+tax, and they had to order it. BEFORE anyone goes to the dealer I suggest to call first, and ask them if they have it in stock. Since door handles are sold painted they will ask you for your car's VIN number so that they match the paint color.
After you pick it up, the replacement will take about an hour (if you know what you doing). The inside door panel has to be removed, it is held in place by the inside door handle and the panel is attached by a number of clips, the handle assembly is attached to the door by three bolts, to remove which you will need a socket with extension. You will also need a good flashlight so you see what you are doing.
If you are familiar how to do this type of work and plan to keep the car for a while I strongly suggest buying a factory service manual on a CD (I bought mine on eBay for under $10). It is worth its price 1000s of times over, and makes almost ALL repair work SOOO much easier.751424a.jpg73e3811.jpgd240851.jpg

Posted on Nov 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i get rear inner door panel off of a peugeot 206 52 plate


remove two screws from armrest (usually covered by small plastic insert) prise out trim from door handle, gently ease panel out from bottom and slip upwards to release from window, once loose if car has electric windows disconnect wires.

Jul 11, 2014 | 2003 Peugeot 206

1 Answer

Back door on peugeot 206 estate car wont open how do i fix


Peugeot 206 hdi 2006 all doors been opening fine and the back passengers door has been sticking sometimes but we could here like a whistling noise from back rear door behind passenger seat. we cantopen it now please can someone help

Feb 23, 2012 | 2005 Peugeot 206 1.4

1 Answer

Need to know how to replace the exterior door handle on a 1997 ford thunderbird.


Ever considered you have to remove the inner door
panel just to get to it?

Jul 26, 2011 | 1997 Ford Thunderbird LX

1 Answer

The red stop sign on a peugeot 206 1.4 lx auto what does it mean


door not shut properly or check water and oil levels as well.

May 27, 2011 | Peugeot 405 Cars & Trucks

1 Answer

When I press the remote on my Peugeot 206 (1998) central


the "unit"is inside the rear door(each door has its own)and the reason 206 didnt come up is this is primarily an American website but as i live in the uk.....you could spray wd40 into the lock mechanism,may be cheaper than replacing reciever.

May 01, 2010 | 1989 Peugeot 405

1 Answer

How do you take off the window winder handle on a peugeot 206


am sure you have not changed the winder since you bought the car.for the first time it is alway difficult getting it out except those that are skilled.however, there is a clip that makes it so firm.

Nov 22, 2009 | 1990 Peugeot 405

1 Answer

Random Overheating Problem on Peugeot 206


It sounds like your thermostat has gone bad and sticking close, Replace the Thermostat and Antifreeze. When replacing the thermostat, buy a fail safe thermostat so you will not have a overheating problem when the thermostat fails. Good luck and hope this helps. Keep me posted, be glad to help.

Jun 22, 2009 | 1991 Peugeot 405

1 Answer

Peugeot 206 lx revs up no reason


try cleaning the idle speed control valve this may be sticking

Jun 19, 2009 | Peugeot 504 Cars & Trucks

1 Answer

Replace left front door outside handle pot metal tip broke off


SECTION 501-14: Handles, Locks, Latches and Entry Systems 2001 Escape Workshop Manual REMOVAL AND INSTALLATION Exterior Front Door Handle Removal and Installation
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. Position the watershield aside.
  1. NOTE: The tie strap does not need to be reinstalled.
    If equipped, remove the tie strap from the anti-theft guard.
  1. Remove the screws and position the anti-theft guard aside.
  1. Release the clip and disconnect the exterior door handle actuating rod.
88661dd.gif
  1. Remove the anti-theft guard.
  1. Remove the exterior door handle screw.
  1. Remove the exterior handle actuating rod.
  1. Remove the exterior door handle lock cylinder cover.
  1. Remove the exterior door handle.

Apr 25, 2009 | 2001 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

389 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

mike hayward

Level 2 Expert

279 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...