Question about 1999 Mazda Protege
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
It is most likely caused by one of the ABS wheel speed sensors, those little cylindrical nipples on the back of your rotors with the cable attached to them. One way to confirm it is to read out the OBD2 codes for the ABS system, but there are some checks you can do. Visually check all four cables and sensors , and make sure there is no build up on the sensors. Make sure that the connector they plug into has good connections. Look at the wheel speed sensor and make sure the gap between the sensor head and the sprocket is the same on all four wheels (should be no more than a mm). Disconnect the wheel speed sensor cable and use an ohm-meter to check the resistance of all four sensors (they should all be similar, but don't remember the value exactly). There is a way to just disable the ABS by pulling out the 60A fuse, but if you do that you may have to plug in a code reader and use a grounding jumper on the ABS electical access box (don't remember which pin) to reset the ABS faults, otherwise you won't be able to drive around like that because your engine rpm at high speeds will behave erratically. Also, do not drive around without fixing this problem or bypassing ABS completely because it could get you into an accident. My ABS problem was intermittent, and the ABS would sometimes kick in on completely dry pavement as soon as I touched the break pedal, it almost caused me to rear-end a car on couple of occasions.
Posted on Jul 30, 2008
SOURCE: Mazda 3 year 2006, SRS light ON.
the srs light comes on once the bag explodes however after installng the bag you have to also instal the relay which triggers the air bag or the light stays on problem is not in the bcm
Posted on Nov 19, 2008
try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you
Posted on Mar 21, 2009
had the same prob on mine underneath the front seats are seat belt tensioner plugs 1 under driver and 1 under pass. seat unplug them and plug them back in , i found this solution on this site somewhere and it worked saved me a lot of money, almost took it to the dealer
Posted on Mar 27, 2009
In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering wheel to access the part. WARNING: Failure to follow factory Airbag disarming protocol can result in an unexpected Airbag deployment and possible serious personnel injury or death.
Posted on May 20, 2009
Tips for a great answer:
Dec 27, 2015 | Cars & Trucks
Oct 30, 2015 | 2010 Ford Escape XLS
Apr 02, 2015 | 2007 Mazda 6
this warning light or any other stays on in the dash it is indicating
that the systems control module (or the system sensor in the case of
lights like low oil pressure, door open indicators etc.) has detected
a fault, it then disables the system (this applies to ABS,TCS, TCM,
SRS and BCM faults and others) as long as the light is on. You must
now have the dealer hook up a special electronic diagnostic tool and
"scan" the system for the fault code that is stored for the
Legend of Abbreviations. ABS Antilock brake system.TCS Traction control system, TCM Transmission control module, SRS Supplemental restraint system, BCM Body control module
Oct 17, 2012 | 2001 Hyundai Santa Fe
Feb 25, 2010 | 2002 Dodge Dakota Club Cab
Jan 31, 2010 | 2001 Dodge Caravan
Apr 09, 2009 | 2003 Mazda Tribute
Feb 21, 2009 | 1999 Chevrolet Suburban
Jan 26, 2009 | 2002 Mazda Tribute
228 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: