Question about 1994 Mazda 323

1 Answer

Cooler fan delay in cooler fan

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi ir i have the same problem,please give the solution

Posted on Oct 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the radiator on a 96 lincoln contiental 32v intech V8 ?


RADIATOR
Removal
1. Disconnect battery ground cable.
2. Drain engine cooling system as described.
3. Remove engine air cleaner.
4. Remove upper radiator hose from water bypass tube.
5. Remove radiator overflow hose from radiator and fan shroud.
6. Remove transmission oil cooler line from oil cooler inlet fitting.
7. Remove nuts retaining A/C condenser core to the radiator.
8. Disconnect engine control sensor wiring from the auxiliary electric cooling fan motors and the CCRM.
9. Raise vehicle on hoist.
10. Remove splash shield from lower radiator support and front sub-frame.
11. Remove lower radiator hose from radiator.
12. Remove oil transmission cooler line from oil cooler outlet fitting on radiator.
13. Remove retaining screws for power steering/transaxle oil cooler and position cooler aside.
14. Support fan shroud, radiator and A/C condenser core with a suitable jackstand. Remove lower radiator
support.
15. Position jackstand aside and carefully remove radiator and fan shroud.
16. Remove two retaining bolts for fan shroud at top of radiator and remove fan shroud from radiator.
17. Remove upper radiator hose from radiator.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
18. Remove Radiator

Apr 19, 2015 | 1996 Lincoln Continental

1 Answer

Why would both low beam headlights go out at the same 2009 ex35 infinity


NHTSA issued recall number 14V755 to address Low Beam headlights being extinguished. GM stated the problem is the headlight delay module (HDM) may not operate in the thermal environment of the underhood electrical center. GM has not issued a fix as yet. Here are four ways I know of to correct this.
1. Have a spare HDM and replace at the first flicker of trouble.
2. Install a heat shield to wick heat away from the electrical center.
3. Install a cooler (fail open) thermostat and run the ac constantly. The ac turns on an additional cooling fan.
4. Loosen the cover on the electrical center to allow air (and dirt) to circulate.

Jul 12, 2014 | 2005 Buick LaCrosse

1 Answer

Take out the radiotor


7_2_2012_11_56_25_pm.gif

REMOVAL

  1. Remove engine under covers.
  2. Drain engine coolant.
  3. W/ A/C: Remove cooler condenser.
  4. Remove radiator assembly.
(a)Disconnect the connectors and wire:
(b)Disconnect these hoses:
  • Upper radiator hose from radiator.
  • Lower radiator hose from radiator.
  • Radiator reservoir hose from radiator.
  • 2 Automatic Transaxle (A/T) oil cooler hoses from oil cooler pipe

7_2_2012_11_57_28_pm.gif

(c)Remove the 2 bolts and 2 upper radiator supports. (d)Remove the radiator assembly.(e)Remove the 2 lower radiator supports
7_2_2012_11_58_54_pm.gif
  1. w/ A/C: Remove No. 2 cooling fan from radiator. Remove the 3 bolts and cooling fan

  1. Remove No. 1 cooling fan from radiator. Remove the 4 bolts and cooling fan.
INSTALLATION
Installation is in the reverse order of removal.

NOTE (A/T only): After installation, check that the rubber cushion (A) of the support is not depressed.
  • Install No. 1 cooling fan to radiator, 4 bolts. Torque: 5.0 Nm (43 inch lbs.)
  • w/ A/C: Install No. 2 cooling fan to radiator, 3 bolts. Torque: 5.0 Nm (43 inch lbs.)
  • Install the 2 upper radiator supports and 2 bolts. Torque: 13 Nm (9 ft. lbs.)

Jul 02, 2012 | 1999 Toyota RAV4

1 Answer

Radiator installation on 2003 Kia Sorento


That is a VERY easy radiator.
Loosen radiator drain plug and drain coolant from radiator.
Disconnect cooling fan connectorsRemove upper and lower radiator hoses after marking them to ease installation.
For vehicles equipped with automatic transaxles, disconnect transmission cooler lines at transaxle.
Remove air conditioner condenser fixing bolts and radiator bracket fixing nuts.
Remove the radiator, radiator cooling fan, air conditioning cooling fan and transmission cooler lines from the vehicle as an assembly.
Transfer all necessary parts (fan assemblies, cooler lines, clips, speed nuts, fittings, etc.) to the new radiator.

Reverse procedure to install.

Fill and bleed cooling system.

Apr 14, 2012 | 2003 Kia Sorento

1 Answer

I have a honda civic lxi 1994 it keeps running hot, and does the fans have a delay until the radiator is hot?


Rads have a delay, but shoud come on when the temp guage reads half, if the fans are not coming on then first change the thermo stat, then the temp sensor if the fans are not coming on.

May 02, 2011 | Honda Civic Cars & Trucks

2 Answers

How to remove radiator from my 2000 chrysler 300


Radiator Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect negative cable.
  3. Drain cooling system.
  4. Remove or disconnect the following:
    • Radiator upper crossmember
    • Upper and lower coolant hoses from the radiator
    • Transmission hoses from cooler
    • Engine oil cooler lines (if equipped)
    • Radiator fan electrical connector and fan assembly
    • Condenser mounting screws located at the front of the radiator
    • Transmission cooler line bracket from left side of radiator
  5. Lift condenser upward enough to disengage upper mounting clips. Allow condenser to rest on lower radiator crossmember.
  6. Lifted radiator from engine compartment.
To Install:
  1. Seat the radiator assembly lower rubber isolators into the mounting holes in radiator lower support.
  2. Attach air conditioning condenser to radiator
    • Torque to 45 inch lbs. (5 Nm)
  3. Install or connect the following:
    • Radiator lower hose
    • Transmission cooler line bracket and transmission hoses
      1. Torque to 28 inch lbs. (3 Nm)
    • Radiator fan and electrical connector
    • Engine oil cooler lines (if equipped)
      1. Torque to 160 inch lbs. (18 Nm)
    • Radiator upper hose
    • Radiator upper support crossmember
    • Negative cable
  4. Fill cooling system with coolant.
prev.gif next.gif

Aug 03, 2010 | 1999 Chrysler 300M

1 Answer

Want to replace the radiator on my 1997 ford thunderbird


Radiator Aluminum Core, Crossflow — 3.8L (Base) and 4.6L Engines
Removal
  1. Drain engine cooling system as described. Disconnect upper radiator hose (8260) and lower radiator hose (8286) and radiator overflow hose (8075) from the radiator (8005). Disconnect the transmission oil cooler inlet and outlet lines from the radiator.
  1. Remove cooling fan motor,fan blade (8600) and fan shroud (8146) assembly as described.
  1. Remove radiator upper bracket retaining bolts and remove bracket. Lift radiator from vehicle.
Installation
  1. Position the radiator into the vehicle. Install upper brackets and tighten bolts securely.
  1. Connect the transmission oil cooler lines to the transmission oil cooler fittings.
  1. Install cooling fan motor, fan blade and fan shroud assembly as described.
Engine Cooling Fan Motor, Fan Blade and Fan Shroud Assembly, Electrical Removal
  1. Disconnect (pull apart) the male-female cooling fan motor wiring connector at the side of the fan shroud (8146). Remove the male terminal connector retaining clip from the fan shroud mounting tab.
  1. Remove two fan shroud upper retaining bolts at the radiator tanks.
  1. Lift cooling fan motor/fan blade (8600)/fan shroud assembly past radiator (8005), disengaging fan shroud from two lower retaining clips.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten fan shroud retaining bolts to 5.2-7.2 Nm (46-63 lb-in).

  2. 10e2638.gif
    8d231fe.gif HOPE THIS HELPS.

    Oct 30, 2009 | 1997 Ford Thunderbird LX

    3 Answers

    I have a 97 Lincoln Continental. I am trying to replace the cooling fan. I have the shroud loose but can't figure out how to get out. Any help would helpful. Thanks


    YOU NEED TO TAKE IT OUT FROM THE BOTTOM REMOVE PLASTIC SHROUD THEN DRIAN AND PULL LOWER RADIATOR HOSE FROM RADIATOR AND THE REST IS PRETTY SELF EXPLANATORY MAKE SURE YOU BUY THE CLIPS FOR THE WIRRING BEFORE YOU EVEN START

    May 09, 2009 | 1997 Lincoln Continental

    1 Answer

    I need 2 know how to remove the radiator


    THIS IS a 1995 LINCOLN CONTINENTAL W/4.6L ENGINE
    iIBELIEVE TOWN CAR IS DIFFERENT LET ME KNOW IF SO AND PLEASE DONT FORGET TO RATE ME


    REMOVAL
    1. Disconnect battery ground cable (14301).
    2. Drain engine coolant.
    3. Remove engine air cleaner (ACL) (9600).
    4. Remove upper radiator hose (8260) from water bypass tube.
    5. Remove radiator overflow hose (8075) from radiator (8005) and fan shroud (8146). NOTE: Loosen transmission oil cooler lines while securely holding radiator connector with a back-up wrench.
    6. Remove transmission oil cooler line from oil cooler inlet fitting.
    7. Remove nuts retaining A/C condenser core to the radiator.
    8. Disconnect engine control sensor wiring (12A581) from the auxiliary electric cooling fan motors and the CCRM.
    9. Raise vehicle on hoist.
    10. Remove splash shield from lower radiator support (16138) and front sub-frame (5C 145).
    11. Remove lower radiator hose (8286) from radiator. NOTE: Loosen transmission oil cooler lines while securely holding radiator connector with a back-up wrench.
    12. Remove oil transmission cooler line from oil cooler outlet fitting on radiator.
    13. Remove retaining screws for power steering/transaxle oil cooler and position cooler aside.
    14. Support fan shroud, radiator and A/C condenser core (19712) with a suitable jackstand. Remove lower radiator support. Position jackstand aside and carefully remove radiator and fan shroud.
    1. Remove two retaining bolts for fan shroud at top of radiator and remove fan shroud from radiator.
    2. Remove upper radiator hose from radiator.
    INSTALLATION
    1. Follow removal procedure in reverse order.
    2. Tighten fan shroud bolts and A/C condenser core nuts to radiator to 3-5 Nm (27-44 inch lbs.) .
    3. Tighten lower radiator support bolts to 8-11 Nm (71-97 inch lbs.) .
    4. Tighten transmission oil cooler lines to fittings to 25-28 Nm (18-21 inch lbs.) .
    5. Tighten power steering/transaxle oil cooler and splash shield retaining screws securely.
    6. Refill engine coolant.

    Feb 11, 2009 | 1995 Lincoln Continental

    Not finding what you are looking for?
    1994 Mazda 323 Logo

    Related Topics:

    37 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mazda Experts

    yadayada
    yadayada

    Level 3 Expert

    60667 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21936 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Mazda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...