Question about 2003 Chevrolet Impala

1 Answer

Drivetrain clunk when accelerating from a stop

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,140 Answers

Mounts, maybe axles

Posted on May 28, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Clunk under car on acceleration, but goes away after first initial clunk.

I would check the spark plugs and wires or coil packs. Sounds like the ignition system is arcing.

Sep 01, 2015 | 2007 BMW X3 3.0si

1 Answer

Mercedes sprinter thud when accelerating

It sounds like one side of your rear brakes is malfunctioning...or sticking and them braking loose when you move a couple feet.

Sep 05, 2014 | Cars & Trucks

2 Answers

What could cause my 2008 Mercury Mountaineer to occasionally clunk when I start and then run fine?

Sounds like one or both of your universal joins is going bad... Is your mountaineer a 4wd, front wheel drive or rear wheel drive?

Jan 13, 2018 | 2008 Mercury Mountaineer

2 Answers

Everytime I come to a stop I hear a clunk and when I accelerate I hear it again. I can see the shifter moving but I've looked under the truck and nothing is missing or loose. Any ideas?

I would be taking a very close look at the transmission mounts. Two pieces of steel with a block of rubber between them. Over time the rubber will tear or separate from the steel.It's job is to dampen the movement of the drivetrain as well as hold the trann in place. Hope this helps.

Dec 10, 2010 | 1999 Toyota Tacoma PreRunner

1 Answer

When slowing down the transmission feels as if it is jerking in to the next gear.

after checking fluid level is correct, try this, to see if it improves...
into drive,let car accelerate without any gas(do not touch pedal)to max speed (about 30/35mph).stop,then with 1/3rd gas pedal,accelerate to max speed(do not move foot)stop,then foot hard to floor,upto about 60mph,then stop.then only using a max of 1/3rd gas pedal,drive for about have just reset the drivetrain computer setings....the car is fitted with a computer controlled fuzzy logic gearbox,it will try to make you drive as eco as poss,but if used harshly the gearchange can be harsh up and down.....
if driven gently 4th will engage at 43 mph,with a slight clunk.

Jul 30, 2010 | 2003 Volkswagen New Beetle Convertible

1 Answer

Clunk sound when I push gas pedal to fast. Is this a drivetrain or transmisson problem?

I would guess that its a U joint in the drive train. When you accelerate slowly it can handle the stress and doesent clunk but when you step on it it clunks hard. Probably the drive shaft U joint, have it checked out but a U joint shouldnt be thw most expensive of the possibilities and would be a good place to start.

Dec 11, 2009 | 1996 Ford Explorer

4 Answers

Clunking sound at rear axle and not spinning correctly

Hey guys, that clunk that you are hearing is not the differential. all z71s or 4x4 have this problem. its the yoke that enters the transmission on the rear just sand it down with 220 grid sand paper on the outside and inside, the splines tend to get surface rust alot. after you do that put some hi temp grease inside the yoke install it and there you go. the noise stops

Aug 09, 2009 | 2000 Chevrolet Silverado 1500

2 Answers

1996 chevy K1500 transfer case slipping out of 4 wheel drive

Your trouble is most likely not in the transfer case but in the front differential engagement solenoid.

Dec 20, 2008 | 1996 Chevrolet K1500

Not finding what you are looking for?
2003 Chevrolet Impala Logo

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

78238 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides