Question about 2002 Mitsubishi Lancer

1 Answer

How to replace front discs and pads - 2002 Mitsubishi Lancer

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 88 Answers

Front brakes are very simple to do:

  • Pull off the front tires.
  • Remove the brake pads by removing the slide pin bolts where the piston assembly attaches to the caliper mounting bracket. The slide pin bolts are usually a 12 or 14mm bolt. Once the piston assembly is free slide the old brake pads out.
  • Compress the piston back into the caliper by using a large pair of channel lock pliers or a c-clamp. If you don't do this, you won't be able to get the new pads on.
  • Before you put the new pads on, replace the rotor.
  • Remove the two bolts for the caliper mounting bracket. They are in the back and are bigger than the slide pin bolts. Usually a 17 or 19mm bolt.
  • Pull off the caliper mounting bracket.
  • At this point the old rotor should slide right off. If it doesn't slide right off, look for a screw in the center of the rotor, some cars will have a screw there to hold the rotor on. If there's no screw and it still won't come off, try tapping it with a hammer. If you're replacing the rotor, don't be shy.
  • Put the new rotor on. Make sure to clean off any grease with brake cleaner that may be on the braking surface from packaging.
  • Put the caliper mounting bracket back on.
  • Put the new brake pads on. Make sure to use some anti-squeal grease on the back of the pads.
  • Put the caliper assembly back on with the slide pins. Grease up the slide pins as well.
  • Put the wheels back on.
  • Make sure to pump your brakes 10 - 15 times before you drive off. Because you compressed the piston back into the caliper, the piston will not be contacting the brake pads unless you pump the brakes.

Good Luck!
~Brandon

Posted on May 27, 2011

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
bestdarngood
  • 3037 Answers

SOURCE: front pad replacement

  1. Step 1 Remove ½ of the brake fluid from the master cylinder with the syringe and replace the cover. Discard the fluid.
  2. Step 2
  3. Remove the front hubcaps and loosen the wheel nuts using the lug wrench, but do not remove the nuts.
  4. Step 3 Lift the front end of the LeSabre with the floor jack and secure safely onto the jack stands.
  5. Step 4 Remove the wheel nuts and wheels. Screw one wheel nut back onto a wheel stud hand tight to retain the rotor away from the caliper assembly.
  6. Step 5 Place a large C-clamp over the left inboard caliper housing and the outboard pad, and tighten to compress the caliper piston.
  7. Step 6 Remove the two caliper guide bolts using a box end wrench. Remove the caliper and secure it to the vehicle chassis with mechanic's wire or a metal hook.
  8. Step 7 Remove the outboard pad from the caliper on the LeSabre first. Pry it off the outboard caliper housing using the screwdriver.
  9. Step 8 Remove the inboard pad by lifting the retaining clips out of the caliper bore.
  10. Step 9 Clean the surface of the caliper bridge that contacts the backing plate of the pads using a wire brush, and apply a thin coat of brake lubricant to the contact points. Be careful not to let the lubricant get onto the rotor.
  11. Step 10 Install the new inboard brake pad and shim into the caliper piston bore by pressing the retaining clips into the bore until it locks into place.
  12. Step 11 Install the outboard pad onto the caliper housing, making sure to align the retaining clips into the holes in the caliper. Use the screwdriver to convince the clips onto the caliper if necessary.
  13. Step 12 Replace the caliper over the rotor.
  14. Step 13 Clean off the surface of the guide bolts and apply a light coat of lubricant to the smooth surface of them. Align them properly through the rubber boots and bolt the caliper to the knuckle. Tighten the guide bolts using the wrench. Remove the wheel nut from the wheel stud securing the rotor.
  15. Step 14 Replace the wheel and wheel nuts. Tighten the wheel nuts snugly, and re-tighten them (with a torque wrench is recommended set at 100 foot pounds) once the LeSabre is back on the ground.
  16. Step 15 Repeat steps 5 through 14 for the right side.
  17. Step 16 Pump the brake pedal when you're through to seat the new pads against the rotors, then check and add new brake fluid to the master cylinder.

Posted on Jul 16, 2009

canbruce75
  • 1776 Answers

SOURCE: replace front disc pads on 1998 lumina

Visit the autozone.com website and register the car information. It's free and will give you access to an online repair manual for the car. The steps for replacing the brake pads should be available there. It's a handy resource. Hope this helped and best wishes.

Posted on Sep 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake peddle is low,


Pedal, not peddle. First make sure reservoir is full at the brake master cylinder. Then check your brake pads (for disc brakes) and/or brake shoes (for drum brakes). When the pads or shoes are very worn down, you will get a low pedal. If you have disc brakes on the front and drums on the rear wheels, first try just replacing the front brake pads. If you get a good pedal after the front is done, many people tend to let the rear brake shoes go unless they are making noise. These systems are designed to put most of the braking force on the front discs, so the rear shoes do not need changing as often.

May 11, 2017 | Cars & Trucks

1 Answer

Front wheel bearings


first check the pads have not worn down to metal if they have the disc will have to be replaced , if the disc is in good condition and the pistons are free press them back into the cylinders and then the pads can removed .check the master cylinder does not over flow as the pistons are pushed back. Brake fluid is a paint remover. the wheel bearings don't have to be touched to replace pads. After new pads are fitted the brakes will have pumped to bring the pads out to the disc.

Aug 15, 2014 | Cars & Trucks

2 Answers

Squealing at the right front wheel


The brake lining's have worn away, the squealing was metal to metal (worn pad against metal disc) The worn pad will have damaged the brake disc. Very dangerous. You will now have to have new brake pads and discs fitted to BOTH front wheels to put it right. Good luck

Jan 27, 2014 | 1997 Mitsubishi Pajero

1 Answer

Front wheel noise


check front wheel bearings for condition and adjustment. Check the thickness and condition of the disc pads and disc rotors.. Disc pads have a small piece of metal that scratches on the disc rotor when the pads need replacing so it may be that.

Jan 03, 2014 | 2007 Nissan Versa 1.8 Sl Hatchback

1 Answer

1989 toyota pickup front disk brake pads replaced, now the front calipers wont clear the new disk brake pads! Any solutions, please?


remove caliper, push disc all way home, put wheel nut on to hold home, retry fitting them the disc may be slightly scued. If no go try diffrent brand of pad I had same prob with a diffrent car last week & diffrent brand pad was 2mm thiner. If can't exchange pads get piece of emery paper on flat surface & sand away top part of pad material in round motions both ways till they fit. :-)

Jul 09, 2012 | Toyota Cars & Trucks

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

3 Answers

Ford transit 02plate/fwd brake judder..ive had new pads/discs,cv joint,bearings,drive shaft.yet i still got juddering when breaking(not as bad as b4)garage says only thing left is faulty discs(very slight...


you mention replacing the discs/pads. how long ago? the fault described is usually caused by warped brake discs as you mention it comes on the onset of braking. i advice replacing the discs.

Feb 21, 2010 | 2002 Ford Escort

1 Answer

Replace front disc pads on 1998 lumina


Visit the autozone.com website and register the car information. It's free and will give you access to an online repair manual for the car. The steps for replacing the brake pads should be available there. It's a handy resource. Hope this helped and best wishes.

Sep 11, 2009 | 1998 Chevrolet Lumina

2 Answers

2001 brake pad replacement 2001 nissan quest


The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Apr 23, 2009 | 2001 Nissan Quest

Not finding what you are looking for?
2002 Mitsubishi Lancer Logo

357 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...