Question about Pontiac Grand Prix

1 Answer

Power door locks only unlock doors. when actuating the switch to lock the doors the dome light dims. The domelight then stays dim unless you disconnect the battery then re-connect it. Otherwise the domelight stays on indefinitely. In short after attempting to lock the doors to get the domelight to respond correctly you have to disconnect thewn reconnect the battery.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 338 Answers

Sounds like the power door lock relay is hanging up- check relay block and replace

Posted on May 27, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the fuses for the power dock locks on a 2006 montecarlo06ss


DR/LCK fuse 25 amp . located in the I/P block
Fuse Block - I/P
In the right front kick panel

Power Door Locks System Components
The power lock system consists of the following components:
• Body control module (BCM)
• Driver door lock cylinder switch
• Front passenger door lock cylinder switch
• Driver door lock switch
• Front passenger door lock switch
• Door lock actuators in each of the doors
• DR LK Fuse 20-amp
Door Lock System Controls
The Power Door Lock System is controlled by the body control module (BCM) and can be activated by any one of the following:
• A door lock switch lock or unlock actuation
• A door lock cylinder switch unlock actuation
• A keyless entry transmitter actuation
• An automatic door lock actuation (Personalization function)
• An automatic door unlock actuation (Personalization function)
Door Lock Operation
When the body control module (BCM) detects a transition of either of the door lock switches to the lock position, it switches the door lock actuator lock control circuit to voltage. Since the lock actuator unlock control circuits are at ground potential within the BCM, the door lock actuator motors transition to the lock position.
Driver Door Unlock Operation
When the body control module (BCM) detects a transition of either of the door lock switches to the unlock position, it switches the driver door lock actuator unlock control circuit to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the left front (LF) door lock actuator motor transitions to the Unlock position.
The driver door lock actuator unlock control circuit is a dedicated control circuit used only for the driver door lock actuator motor. This is done so that the driver door may be unlocked by itself using a keyless entry transmitter or an automatic door unlock function (if programmed).
Passenger Door Unlock Operation
When the body control module (BCM) detects a transition of either of the door lock switches to the unlock position, it switches the door lock actuator unlock control circuits to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the passenger door lock actuator motors transition to the unlock position.
The door lock actuator unlock control circuits are dedicated control circuits used only for the passenger door lock actuator motors. This is done so that the driver door may be unlocked separate from the passenger doors using a keyless entry transmitter or an automatic door unlock function (if programmed).

Mar 23, 2017 | 2006 Chevrolet Monte Carlo

1 Answer

2006 GMC Envoy: I tested all of the fuses and all of them check out but my power locks, cabin lighting, dash panel lights, etc. aren't working.


Which fuse box ? Do you know what a DDM -is ? Driver door module . Do you have any idea what all is involved in making these thing's you have listed work ? A lot more then a fuse , there could be DTC'S - diagnostic trouble codes stored in the principal Control module ,the BCM , That could save a tech. valubale time in diagnoising this problem !
Door Lock System Components
The power door lock system consists of the following components:
• Driver Door Module (DDM)
• Passenger Door Module (PDM)
• Liftgate Module (LGM)
• Door lock relay
• Door unlock relay
• Body Control Module (BCM)
• Reversible door lock actuators in each of the doors
• LR/RR LOCKS 10A fuse (relay supply voltage)
• Door lock switches in driver and passenger doors (switches are integral components to the DDM and PDM)
Did you know there is a fuse box in the rear of the vehicle ?
Fuse Block - Rear
Beneath the left rear seat
The inside lights are also controlled by the BCM , and the fuse's are also located in the rear fuse box .
The body control module (BCM) directly sends a 5-volt reference voltage to the instrument panel (I/P) dimmer switch which is then adjusted based on the I/P dimmer switch position and returned as a low reference and a signal to the BCM. The BCM uses this signal to directly control the desired level of instrument panel illumination lamp intensity.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC B2620 Display Dimming Pulse Width Modulation (PWM) Input Circuit. There are several DTC'S that can set !
DTC B3801 Passenger Compartment Lamp Request Circuit
DTC B2610 Passenger Compartment Dimming 1 Circuit plus others for power locks .
Thank You Uncle Sam

Nov 29, 2016 | 2006 GMC Envoy

2 Answers

Interior lights


This is both a courtesy and safety issue on many high end vehicles. The light from the interior lights can cast enough light to get to front door and possibly show dangers in your path. And after first getting into you car and starting it, you can check the back seat for any unwanted hitchhikers. As for the 10 minute timer, I don't know if this can be adjusted. A Chiltons/Haynes repair manual for you car may have that answer, or, the Buick dealership shop foreman. Best of luck.

May 31, 2015 | 1998 Buick Park Avenue

1 Answer

Power windows stopped working and dome lights stay on. Power locks work only with the "clicker" but not on driver door


Look under the hood fuse no. 12 should be for power windows. Or maybe something like a bad ground wire in drivers door harness.

Mar 19, 2014 | 2004 Jeep Grand Cherokee

1 Answer

Where is the door lock relay located?


The relay or switch may be shorting, check other door lock controls for correct function, this will rule out relay and isolate the switch or rule out master switch and isolate relay.

Nov 28, 2012 | 1992 GMC Yukon

1 Answer

Intreior lights will not go off


First, some people do not know that the domelight can be turned on by using the headlight control. If it is all the way to one side, the dome lights will turn on.

The Relay for your Theater dimming lights may be stuck. Aside from this, a doorjam switch may be bad. Some switches usually show door ajar, but some switches have more wires and could possibly short while failing to post a door ajar notice.

You can get free wiring diagrams and Relay box info at Autozone.com by registering your vehicle. Also check the dome light itself as many have 3 positions now off, door activated, and constant on.

Sep 30, 2012 | 2002 Jaguar S-Type

1 Answer

2000 chevy monte carlo door latch assy. replacement


all the lights above the dash do not work ?????? DOME light's ??? No light's come on when you open the door or any door ? Wouldn't think all the door ajar switches bad at one time .
Interior Lamps
The interior lamps consists of two groups, lamps that can not be dimmed and lamps that can be dimmed. This first group consists of lamps that may not be dimmed. This Includes those lamps that may be manually turned on by placing the interior lamp switch to the DOME position, or by opening a door or a compartment:
• Auxiliary dome lamp (SEO, RPO 6C7)
• Dome lamp
• instrument panel (I/P) compartment lamp
• Inside rear view mirror lamps
• I/P courtesy lamps
• Reading lamps
• Rear compartment courtesy lamp
• Sunshade vanity mirror lamps
Battery positive voltage is applied at all times to the DIC/RKE fuse and to the switched side of the BATT RUNDOWN PROTECTION relay in the right I/P junction block. The DIC/RKE fuse supplies battery positive voltage to the coil side of the BATT RUNDOWN PROTECTION relay. When the ignition is turned to the ON position, the body control module (BCM) provides a ground to the Inadvertent relay control circuit. This energizes the BATT RUNDOWN PROTECTION relay and applies battery positive voltage to I/P BRP fuse and to the TRK/ROOF/BRP fuse. Battery positive voltage is applied from the I/P BRP fuse to the I/P courtesy lamps, I/P compartment lamp and to the I/P compartment feed circuit to the BCM. Battery positive voltage is also applied from the TRK/ROOF/BRP fuse to the:

If the BCM receives a door lock or unlock input signal, the BCM will activate the BATT RUNDOWN PROTECTION relay, which provides battery positive voltage to all interior courtesy lamps. When any door is opened, the door jam switch contacts close and the BCM receives a door-open input signal. The BCM then applies a ground to the theater dimming ground control circuit illuminating the courtesy and dome lamps.
After all the doors are closed, the courtesy lamps remain illuminated for approximately 40 seconds. The courtesy lamps will also turn on and remain illuminated for approximately 15 seconds after the ignition key is removed, prior to any door being opened.
When the headlamp switch is placed in the DOME position, the BCM receives a ground signal. The BCM then applies a ground to the theater dimming ground control circuit. This illuminates the dome and roof rail lamps.
The courtesy lamps will normally turn off using the theater dimming feature. The BCM provides a pulse width modulated ground to all courtesy/reading, dome, and inside rear view mirror lamps for the theater dimming feature. The BCM will immediately turn off the courtesy lamps if a door lock command is received with all the doors closed, or if the ignition switch is turned to either the ON or RUN position.
The BCM activates the interior lighting output 15 seconds after receiving the class 2 message "Airbags Deployed" from the sensing and diagnostic module (SDM). The interior lamps remain activated for 25 minutes.

The door ajar switch is part of the lock actuator inside the door !

Jul 01, 2017 | 2000 Chevrolet Monte Carlo

1 Answer

2001 Dodge Durango-Just purchased, previous owner had to replace drivers side door. Now the dome light won't go off unless I shut it completely off with the dimmer/on/off on the dash which dims my dash...


Switch is inside the door. by the lock mechanism ( door latch) If you remove door panel you should be able to reach wire it runs outside the door. Interior lights ground threw that wire so it is ether grounded or the switch is bad

Mar 22, 2011 | 2001 Dodge Durango

1 Answer

I bought a 1996 Subaru Impreza L 4dr 5speed AWD that runs and starts fine but when I was installing fog lights i noticed that there appears to be an alarm hooked up (it says "code alarm elite DM...


Battery Constant 12v+ Positive Wire (+): Black/Yellow
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness

Starter Positive Wire (+): Blue/Red
Starter Positive Wire Location: Ignition Switch Harness

Ignition Positive Wire (+): Red
Ignition Positive Wire Location: Ignition Switch Harness

Accessory Positive Wire (+): Red/Yellow
Accessory Positive Wire Location: Ignition Switch Harness

Parking Light Positive Wire (+): Red
Parking Light Positive Wire Location: Low In Drivers Kick Panel

Power Door Lock Negative Wire (-): Add Actuator. This vehicle uses a central door locking system. When connecting a keyless entry, you will need to add a door lock actuator and some units will also require (2) extra relays.
Power Door Lock Negative Wire Location: To Drivers Door Only

Power Door Unlock Negative Wire (-): Add Actuator. This vehicle uses a central door locking system. When connecting a keyless entry, you will need to add a door lock actuator and some units will also require (2) extra relays.
Power Door Unlock Negative Wire Location: To Drivers Door Only

Door Trigger Negative Wire (-): Red/White
Door Trigger Negative Wire Location: In Black Plug, Above Hood Release

Domelight Supervision Wire: Use Door Trigger, Requires Relay
Domelight Supervision Wire Location: N/A

Horn Negative Wire (-): Red/Green
Horn Negative Wire Location: At Steering Column Harness

Tachometer Wire Negative Wire (-): Black/Blue
Tachometer Wire Negative Wire Location: At ECM, Under Drivers Side Dash

Brake Light Positive Wire (+): White/Black
Brake Light Positive Wire Location: At Switch Above Brake Pedal

CODE ALARM SYSTEM

Used on:
Impreza 1996-2001
Legacy 1995-1999
Forester 1998-2000

codealarmremote2.jpgBattery GP-23A

Lock: Left button will lock all doors. Double chirp indicates locked.
Unlock: Right button will unlock driver's door only. Hold unlock button app 6 seconds, it will unlock all doors including rear gate. Single chirp indicated unlock.
If the car chirps or lights flash 4x the alarm was triggered.
Panic. Press both buttons to activate emergency honk and flashing lights.
Valet mode: With optional alarm onlyPress the red alarm button on the left of the steering wheel. The light will quickly double flash. To re-set back to normal mode, press the red alarm light button again

Battery failed and lights flashing?
Parking lights will flash when the vehicle's battery is disconnected and reconnected.
To stop lights from flashing, either:
Press remote transmitter "UNLOCK" button once OR turn the ignition switch to the "ON" position and press programming button for one second (see below).
The vehicle interior (courtesy) light and door open warning light (DOOR AJAR indicator) will then illuminate for 60 seconds when the ignition is turned off, or until the doors are locked with the remote transmitter. Yes, the dashboard instrument panel lights will flash when the parking lights flash.

Programming or Overriding the Alarm when you have lost the remote
Open driver's door.
Turn ignition key to 'On'
Press and *hold programming button* in (see diagram, button under dashboard)
After 15 seconds the the door locks will cycle 3 times. Do not release Programming button.
Press lock (left) button the remotes to be programmed. The door locks will cycle one time. Exit programming mode by releasing Programming button under dashboard and turning key to off.


codealarmremote1.jpgCode Alarm Programming Button is under dashboard on the kick panel by the driver's left knee, left of the steering column. If you can't find it, it might still be tucked up in the wiring harness higher up in that same general area. The botton is recessed in a plastic ring (see diagram).
This button must be pressed while programming remotes or if the battery was disconnected and the lights are flashing.

Jan 05, 2011 | Subaru Impreza Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

287 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...