Question about 1999 Ford Explorer

1 Answer

Changing stabalizer rod - 1999 Ford Explorer

Posted by on

Ad

1 Answer

Whatever your referring to can be unbolted
fairly easy

You will need metric tools most likely

You can also go to YOU TUBE to watch a
Video on how it is done

Posted on May 27, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change shaft stabalizer bar on 2002 buick rendezvous


The stabilizer bard rarely need replaced. There 2 brackets holding the bar in place. They both have a bushing that goes bad from time to time. The real issue with the stabilizer bar is the end- the stabilizer rods on the ends. You can usually replace these in about 1/2 hour and the job is done. Go to your local parts store and order the stabilizer rod and bushing kit, The kit will come with an in instruction sheet, and it is a very simple job.

Dec 31, 2014 | 2002 Buick Rendezvous

1 Answer

There's a clucking noise coming from the front driver side of my 2006 Dodge Charger R/T. What could possibly need replacing if I already changed the tie rods and brake pads?


Stabalizer links. To check them you will need to have both front tires off the ground at the same time. Grab the stabilizer bar where it attaches to the link. Push up and pull down on the bar. If you feel any movement replace them. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Jan 20, 2012 | 2006 Dodge Charger

1 Answer

99 S10 ZR2 has 1-2 second knock when starting. When engine has warmed up there is a stutter when at idle and in gear but clears when throttle is applied> what could be causing this? 4.3L engine


Add a quart a Lucas heavy duty oil stabalizer next oil change an u have a bad iac motor it's an idle air control solenoid it's what's regulates the engine at idle it's attached to the throttle body by two 10 mm bolts fairly easy an inexpensive to fix an the Lucas will take care of that rod knock u got good luck an hope this helps ya out

Jul 21, 2011 | Chevrolet S 10 Cars & Trucks

1 Answer

I changed out spark plug wires last week 1990 Ford f150 Lariat. This week it sounds like a hard knocking from engine after driving 10 to 20 miles. Is my timing off by just changing the spark plug wires?


Knock at low rpm and high rpm" It may be oil pump , After oil heats up it gets thinner and and less lubracated. I would change the oil and add some oil stabalizer, shouls help, if not probaly a rod.

Mar 19, 2011 | 1990 Ford F150

1 Answer

Fail light for ride stabalization light


leaking stabalizing air bag and or hoses or fittings

May 19, 2009 | 2008 Saab 9-3

2 Answers

Front suspension


Jacking car on frame rail, the front end should be very tight. No play in tie rod ends, ball joints or wheel bearings. GM has sloppy front end parts.

May 09, 2009 | Chevrolet Lumina Cars & Trucks

3 Answers

Engine noises


Its not a rod this is a common problem its your valves the best thing i have found is to use vavoline maxlife 5/30 high millage oil a can of six cylinder restore and a fram high millage oil filter. you will be amazed at how quick this remedy's your problem . Plus the car will tell you when your with in a thousand miles of oil change when the tick comes back time to do oil change. this will cost you around 30 dollars if you do it your self or 58 art wal mart. and for the other guy he deserves a bad rating. insert rasberry

Jan 03, 2009 | 1995 Isuzu Rodeo

1 Answer

1995 Mercury Grand Marquis Suspension


JacDempsey, how about shocks/struts? If they are bad, that could be what u need to cruise the highway nice and smooth the way a Grand Marquis should.

Dec 08, 2008 | 1997 Mercury Grand Marquis

1 Answer

I can feel every crack I roll over 1995 Mercury Grand Marquis.


i see you have replaced everything on front end but one thing, the shocks,a good set of gas filled shocks will give you a better ride..

Dec 08, 2008 | 1997 Mercury Grand Marquis

Not finding what you are looking for?
1999 Ford Explorer Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...