Question about 2006 Chevrolet Equinox

1 Answer

How do i remove the iginition cylinder? The key will no longer turn in the cylinder .

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,140 Answers

Have to remove steering wheel

Posted on May 28, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Iginition lock cylinder replacement without a key

not just the cylinder, youd have to drill it out.
take it to any lock smith shop , they will tell you.
it has a pin, you pull and insert the key...

Nov 30, 2013 | 1993 Toyota Tercel

1 Answer

Key go in iginition cylinder turn over but car will not start but lights and everuthing does work

Hi mirangel2,

You most likely wont be able to fix this yourself! I'm sure your spark plug or fuel injection system may be damaged. Please see a mechanic!


Feb 21, 2011 | 1995 Pontiac Bonneville

1 Answer

How do I get the old iginition key lock out of the

There should be a button inside the column that you push in, or a bolt to remove, been awhile since I did one. You may need to have the key in the lock cylinder and turn the lock cylinder.

Apr 23, 2010 | 1982 Chevrolet El Camino

1 Answer

I am trying to remove the iginition cylinder, but it will not come out. Does the key have to be turned on to remove the cylinder? How do I get the cylinder out if I can not turn the key. That is the...

No you do not need a key you have to remove the cover around the steering column, Thin you will find there are 3or4 safety tip torx screws remove the hole unit, and replace with new you may find it easier it you git new unit first and ,look at it.please let us know if this helped ,Thank you.

Mar 30, 2010 | 2002 Dodge Grand Caravan

1 Answer

What's the trick to removing the iginition key cylinder

you most likely have a dowel pin that you will have to remove. You can get instructions on how to do this at Auto Zone-they can print it out for you.

Mar 22, 2010 | 2003 Dodge Neon

1 Answer

Key iginition will not turn think barrel is worn sometimes turns sometimes does not. is it something i can do myself? how many bolts hold it on? where can i get a picture of it? i called for a price and...

It is something you can do yourself (for alot less money)
I am assuming you are removing just the Lock Cylinder and not the entire Ignition switch?
For JUST the Lock Cylinder:
1. Disconnect the negative side of the battery.
2. Remove the lower steering column cover under the steering column. It has three (3) screws.
3. Insert the Key and turn to the RUN position.
4. Using a small screw driver - depress the Lock Retaining Tab. It is located right of center on the column in the area of the Key insertion area.
5. Remove the Lock Cylinder.
To Install:
1. Insert the Lock Cylinder in the "Lock" Position.
2. While pushing in - insert the Key and turn it clockwise to the Run Position.
Let me know if this helped. If it is the entire Ignition Switch, let me know with an email to this post. I will send the additional infomation (for free).

Jan 01, 2010 | 2002 Dodge Grand Caravan

1 Answer

The iginition key had a hard time going into my 95 Camaro today and when it finally did it didn't turn real easy. This is a first time event and it didn't help to turn the steering wheel. Any thoughts on...

Sounds like the ignition luck cylinder are worn and needs to be replaced. There are tumblers in the cylinder lock that will seize up due to dirt and metal filings from the key it self. Try spraying some lock cleaner and lube in the ignition cylinder and have a new key cut if the key's it self is worn out. Good luck and hope you do not have to replace the lock. Keep me posted.

Nov 25, 2009 | 1995 Chevrolet Camaro

1 Answer

Bmw 316i

hi markjones, the ignition switch can usually be removed without too much disassembly. First you will need to remove a plastic screw in the upper and lower trim covers. Seperate the covers. You should see a black plastic ring around the mechanical switch. gentley remove the ring. Next remove the rubber o-ring/band. With the key in the iginition and turned to almost to position 1, insert a heavy duty paper clip, or bmw special tool (about $30 from the dealer) into the small hole in the switch. There is a cam in the hole that needs to be twisted clockwise so the cylinder can be removed. When installing a new switch make sure to remove the little tab pice of metal that usually breaks off in the housing. Also be sure to make sure and reinstall the rubber ring/band because they are part of the ews system. If you key turns continuously, or is not able to be removed, the ignition housing and cylinder both will need replaced. Replacing the lock housing is about a 2 hour sequence and can be challenging. I would recommend a shop for that kind of repair.

Jan 19, 2009 | 1996 BMW 318

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides