Question about Volkswagen Jetta

1 Answer

Can't find fuel lines for sale. Can't figure out what the separate fuel lines are called. I know there are seven of them. Where should i begin.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 1,705 Answers

Posted on May 27, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Does my 1974 dodge dart with a 318 motor have a fuel return line on it fuel sending unit?

Hey Jim,I see that it is showing 2 types at auto part stores.You can see the return line on the one with it,the way to find out is when you change you will see.Not good to buy in advance,may have to order.
  1. Usually a pump with a return will have a separate connection to go from the pump back to the cell. If yours has that connection ,I would put the return line back to the cell on it.
    A return line is nothing more than excess fuel being returned to the cell.

Jan 04, 2013 | Cars & Trucks

1 Answer

Fuel line

Ask for the 2 lines coming off the sending unit. to the main line. That should be enough for ordering them. be sure to change your feul filter while you're there good luck

Jan 01, 2013 | 1999 Pontiac Sunfire

1 Answer

Where is fuel filter located on 98 sebring convertible?

I'm showing a separate filter for that model, so it should be under the car near the front of the gas tank. Just follow the fuel line.
Some Chrysler models were in the tank with the fuel pump.

Jul 23, 2012 | Chrysler Sebring Cars & Trucks

1 Answer

Starts perfectly but won't idle

are their any codes either stored or open might be a fuel supply issue is it starving out or just stopping if just stopping check all related fuses if starving for fuel check fuel lines fuel filter back to the fuel pump. also it could be an injector issye

Jul 07, 2012 | 1989 Mazda 626

1 Answer

Looking to take a look at the fuel filter on a 1998 Lincoln continental, and I'd like to know where exactly its located and how to remove with what tools required.

Replacing Lincoln Continental fuel filters requires a spring expander tool. The fuel filter and the fuel lines to the injectors are held in with a circular spring housed in the end of the line. The line itself that the spring clamp slides over has a raised part on the line, and when the spring connector is pushed over this section, the clamp expands to go over the raised section and then collapses once more on the other side, holding the two pieces together. The spring expander tool is a small L-shaped expander the fits over the line and when pushed into the spring expands the spring so it will enable the pieces to be separated.
  • Lift the hood and locate the Schrader valve on top of the fuel rail. The fuel rail sits on the injectors. It looks like a bicycle tire valve. Remove the cap and use a small screwdriver or similar tool and press in slightly on the valve stem to release any pressure in the fuel line. It is a good idea to put a rag in front of the valve for the escaping fuel, but there won't be much lost (mostly pressure).
    Raise and support the car on jack stands for safety. The fuel filter is on the driver's side about midway back on the frame rail. Loosen the pinch bolt that holds the filter to the bracket. Insert the fuel line tool onto the metal line with the long end facing the filter. Push the end of the tool into the spring with a little twisting motion, keeping a little pressure on the tool toward the filter. Once the spring is expanded over the tool, rotate the filter a little and pull it away from the line to separate the two. Once the one side is separated, do the same to the other side. Be careful--though there is no longer fuel pressure, the filter is still full of fuel and will pour out if tipped. Pull the filter out of the bracket.
  • Before installing the new filter, make sure that it is oriented properly. There is an arrow on the filter pointing toward the engine that says "flow." Install the filter into the bracket with the arrow pointing forward. Insert the fuel lines with the spring locks one at a time. Push the filter hard enough to hear or see the spring snap into place. Do the other line the same way and then tighten the pinch bolt in the bracket. Cycle the ignition key several times to prime the fuel line and check for leaks.

Jun 27, 2012 | Cars & Trucks

1 Answer

How do I release a fuel line?

Going to do my best to explain it and made you some fancy pictures. Your fuel lines need to be separated by a special tool that you can get at your local auto parts store. Just tell them you have a Ford and need the tool to separate a fuel line and they should know but there are different sizes. In the one picture with the arrows, the red arrow is pointing to the "housing" I guess you can say. Inside there is a spring. The blue arrow shows you a little tab on the special tool. Close that tool over the line, push the tab that's on the tool toward the spring which will open up that spring. While the tool has the spring opened separate the fuel lines. To install make sure the O-rings on the line are nice and clean and maybe put a very little bit of oil on the O-rings to lubricate it a bit and simply push them back together. You can hear a little "click" as they go back together or at least feel it "snap" back together. Just try to pull them back apart a little to make sure it is back in place and ALWAYS check for a fuel leak when done. I hope this helps and good luck.


Jul 27, 2011 | 1998 Ford Ranger SuperCab

2 Answers

99 Chev Suburban,Just quit while driving. After

I would recommend performing a fuel pressure test to start with..

Mar 31, 2010 | 1999 Chevrolet Suburban

3 Answers

I have a 92 f250 7.3 diesel idi, that i replaced the fuel filter/water separator and fuel pump.I have cleaned the lines out form front to rear and no fuel. I pulled the fuel pump off and bench check it and...

try loosening the injector lines a little then crank probably has air in the lines and wont blow through the injectors,once fuel comes out while cranking,tighten them,if this is the problem it should start but run rough untill the lines are tight,it shouldnt hurt much to get a little fuel on the engine

Oct 21, 2009 | 1992 Ford F250

1 Answer

Fuel line clip replacement

depending on the style of the clip if it is the small white press in clip the clip can be bought separate

Mar 27, 2009 | 2006 Ford F-150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

80637 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides