Question about 2005 Chevrolet Equinox

1 Answer

2008 chevy equinox. Removed all bolts, removed the caliber but rotor will not come off. Spaid hub and still wont come off. Is the E brake holding it or should I just bang harder ? Any trick/help would be appreciated.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 5,332 Answers

Bang harder. They tend to rust up where it meets the hub and seize up. Eventually it will come loose. If it's the rear rotor once you can wiggle it you will be able to work it around the brake shoes if needed. Most of the time ounce you get it broken free from the hub they slide right off.

Posted on May 27, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do u remove hubs on a 1992 Isuzu big horn


TO DO WHAT? not even the smallest hint on job or failure.>?
USA?
hubs, the rears have hubs to with disc brake option.rotor hubs.
I guess front hubs?.
guess 2, wheel bearing hubs, and not 4wd axle locking hub units.
doing what?
brakes, wheel bearings, axle damage. 4wd axle bearings what?
the pages are 2wd pages, and 4 wd pages, which is yours?
is this your first time DIY ever. ? or first time 4wd?
guess 3, 4wd, how am I guessing....


names
Acura SLX
Chevrolet Trooper
Isuzu Bighorn
Holden Jackaroo
Holden Monterey
Honda Horizon
HSV Jackaroo
Opel Monterey
Subaru Bighorn
Vauxhall Monterey
wow......
our usa book lists it as trooper only.
so ...

just B or B then A off? if you had b off, you'd see what?, a big nut.
that is locked to spindle shaft.
ill guess? wheel bearings are bad? (just in hub not spindle bearings bad... no matter this is first.)
so you do what. ? here are the steps.

that part"B" must be off first, see the bolts holding it, ?
B = auto locking hubs. or hub axle lockers.
26005769-b5pjo3cin0lhc1b54v4xlnuy-4-0.jpg you can see the caliber must come off, so, do so and tie them up.
  1. "Place the Transfer shift in the 2H position.
  2. Raise and support the front of the vehicle safely on jackstands. (rear tires chocked, and hand brake set hard)
  3. Remove the wheel and tire assembly.
  4. Loosen the hub to rotor retainer bolts.
  5. Remove the brake caliper mounting bolts and carefully remove the caliper (along with the brake pads) from the rotor. Do not disconnect the brake line. Secure the caliper out of the way with the flexible line still connected.
  6. Remove the hub nut using hub wrench J-29020-A or equivalent. ( special tool)
  7. Remove the hub cap assembly retainer bolts. Remove the spindle nut, washers, and other components. Remove the hub/rotor, being careful not to drop the outer wheel bearings. As the hub/rotor is pulled forward, the outer wheel bearings will often fall forward.
  8. Once the hub/rotor is removed, remove the retainer bolts securing the rotor and hub together. Inspect the hub and replace if needed."
  9. end removal. install is next... (alldata.com covers this)

Dec 13, 2015 | Isuzu Cars & Trucks

1 Answer

Replace rear rotors 2004 jeep cherokee


Heres what you will need to do this type of job. First you will need a rachet and metric sockets with an extention if available. Also you will need somthing to press the caliber piston back into place a special tool or some kind of press would work . A plastic auto hammer to knock the rotors loose, somtimes they can be difficult to remove. Pliers would be needed as well as a screw driver to help mount the caliber or pads back into place. One thing to keep in mind is that if you indeed are replacing the rear rotors, it is recommended to get new pads as well. This is for the reason that old pads will cause break sqealing since they are not surfaced perfectly straight for the new rotor. Step one will be to get the caliber of the vehicle so if there is a medal clip on one of the studs just use the pliers to rip it off. Then use the rachet to remove two bolts holding the caliber. After you remove those bolts, there should be another two bolts holding the caliber bracket as well, do the same procedure in removing those. IMPORTANT do not let the caliber hang by the brake cable, put it on a stand or in a location where it is not free fall hanging. Now you should just have the rotor left, try pulling on it to see if it breaks loose, if not then use your plastic hammer to bang in the back of the rotor and knock it loose that way. If I remember correclty those rear rotors will have brake shoes underneath. Do not wory about those they are there for your emergency brakes. Now put the new rotor on and make sure it is securley installed on the wheel hub. Install you'r bracket first, then begine to install your caliber back into place. NOTE the caliber may not install to easy onto the rotor for the reason that you will need to compress the piston inside with either the special tool or some type of press. If you compress it and you hear brake fluid dripping down, it is nothing to worry about, its just the fluid being pushed back by pressure. Install the caliber and pads the same way as removal paying close attention to the other side if your not sure of how the originally were installed. When all this is finished look up brake bleading on YOUTUBE.com to accurately bleed your brakes and remove any air inside that may cause spongy or moister inside your brake lines.

Hope this Helps!

Jun 07, 2011 | 2004 Jeep Grand Cherokee

1 Answer

How hard is it to replace hub assembly(bearings) on a 1999 Monte Carlo z34?


Not to bad you need remove wheel first then remove 2 bolts from brake caliber put caliber to the side or better yet hang it on the stut spring with a zip tie then remove 2 bolts that hold the brake caliber bracket on put it to the side then remove rotor then remove the big nut on the center of the axle then get a hub puller or a cold chisel to seperate the hub from the steering knuckle oh disconnect the ABS sensor from connection.

May 12, 2011 | 1999 Chevrolet Monte Carlo

1 Answer

I have a 2008 Lincoln Mkz, when the car is in drive and my foot is on the brakes it vibrates what is causing that.


1.Check to make sure there are no broken belts on the tires, run you hand over your tires to feel for lumps if so you need to replace the tire.
2.Most likely what is causing the issue is your rotor, you need to remove the brake caliber, to do that there are 2 bolts holding the caliber on. make sure it is not warped.
3.You can usually pick up calibers for less then 50 dollars. Hope this helps

Mar 30, 2011 | 2008 Lincoln Mkz

1 Answer

How do I remove front rotors on a 2006 chevy equinox awd


You will need to remove 4 bolts once you take the tire off. two bolts on your caliper need to be removed. using screwdriver pry off cali[per. remove the two bolts holding caraige(brake pad mount bracket) and bracket should come off. hit brake rotor with hammer and be care ful not to damage studs. brake rotor should come off

Oct 17, 2010 | 2006 Chevrolet Equinox

1 Answer

Cannot remove front rotor. Caliper and pads


Raise vehicle and remove wheels. Disconnect brakeli
ne from caliper (if necessary). Remove caliper.

On models with free wheeling hub, set control handl
e to FREE position. On all models, remove hub
cover, bolt/washer and hub body. Use tapered punch
to open slits of conical washers. Remove axle shaft

snap ring (if equipped).

Straighten tabs of outer lock washer. Using Spindle
Socket (09607-60020), remove lock nut, lock washer

and adjusting nut. Remove thrust washer and outer b
earing. Remove axle hub and rotor. Remove grease se
al
and inner bearing. Press hub bolts out of axle hub.
Remove retaining bolts, and separate rotor from hu
b.

Mar 20, 2010 | 1996 Toyota Land Cruiser

2 Answers

Changing rotor of a 1993 ford f150 4x4


remove cap on hub then remove carter key take off nut and remove hub

Mar 20, 2010 | 1993 Ford F150 SuperCab

2 Answers

I have a 95 Chevy suburban and I am trying to change the rotor and can not get it off. The lugs are attached to the rotor and not sure what I should do


Removing: Loosen lug nuts (7/8") and spindle nut (36mm). Lift truck. Remove lug nuts, spindle nut, and wheel. Remove 2 bolts (3/8" allen) holding calipers on. Hold the calipers up with a bungee cord. I attached it to the sheet metal of the fender. Remove 4 bolts (15mm) from rear of hubs. Once these bolts are removed you can move the shield that is in-between the hub and the axle(I think). You are moving it to get access to the allen bolt that holds the ABS sensor on. Once you move the shield then you can look through the top of the rotor through the slots and see the sensor line and bolt. I don't remember what size allen this one took. You do need a long allen wrench though. Disconnect sensing line from hub. Now the rotor is ready to come off. I had to use a pry bar to remove this gently working each side until it popped off. Once the rotor is removed, you need to hammer out the lug bolts. Then you have to tap the rotor away from the hub. This took a little work. Then check each of the lug bolts by screwing the lug nuts on them. They should go all the way down by hand. If they don't - go buy new bolts $2 a piece. Installing: Position new rotor on hub. Get some dry ice from your local grocery store and freeze the bolts for about 10 minutes. Pull one bolt out of the ice at a time and install on the rotor and tighten the bolt with the lug nut. I put the nuts on upside down and used a 7/8" wrench and mallet to tap on the wrench to get these as tight as possible. You also have to tap on the head of the bolt and repeat the wrench tapping. Do this for each bolt pulling one out of the ice at a time. You do not have to get the rotor and hub completely together but get it as close together as possible. Once all of the lug bolts are in it is time to put the rotor on the truck. Ensure the shield is on the spindle and install the rotor, again, this takes some work. Once the rotor is on, connect the ABS sensing line. Line up the shield and install 4 bolts to rear of hub. You can align these by moving the hub, not the rotor. Install the caliper, remember to put brake grease on these 2 bolts. You may have to compress the caliper slightly. To do this remove the brake pad that has the circular part of the caliper touching it. Open the brake fill cap on the master cylinder. Use a C-clamp to compress the circular part. Reinstall the brake pad and brake fill cap. Install the caliper. Install the wheel and tighten lug nuts. I used a cheater bar on my tire iron and ensured that the lug bolts were flush with the head of the lug nuts. Then I removed the wheel to verify that the gap between the rotor and the hub was gone. Reinstall wheel, tighten lug nuts, and tighten spindle nut. Once both brakes have been replaced, start up the truck and pump the brakes several times till you feel some tension when pressing them.

Nov 25, 2009 | 2000 Dodge Durango

2 Answers

How to change front wheel bearings on a KE 89 model please ":)


im havent had to much experience with mazdas but for most cars you can buy the hub and replace the whole thing at once remove tire then remove brake pads and rotor un bolt the 2 bolts that bolt to strut then drop lower balljoint then pull cv joint out of hub there should be 3 bolts holding hub on the engine side remove bolts pull off hub replace

Jul 25, 2009 | 1988 Mazda 323 Hatchback

1 Answer

96 honda accord Removing brake rotor


hi remove the the rotors retaining screws then remove the two bolts holding the caliper and pull it out of the way take the rotor off yates210456

Oct 01, 2008 | 1996 Honda Accord

Not finding what you are looking for?
2005 Chevrolet Equinox Logo

387 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...