Question about 2008 Dodge Avenger

1 Answer

What is the spark plug gap for a 2008 dodge avenger with a 4 cylinder?

Posted by on

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

There should be a data plate on the radiator support or a decal on the under side of the hood that has the reccomened plug gap.

Posted on May 27, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change the rear 3 plugso on a 2008 dodge avenger


2.5 liter?

The plenum will need to be removed in order the replace the rear spark plugs.

Apr 04, 2015 | 2008 Dodge Avenger

1 Answer

Spark plug gap 2008 avenger 6 cylinder


check your owners manual it there as well look under the hood its on a decal on the rad support or the underside of the hood

Aug 09, 2014 | 2008 Dodge Avenger

2 Answers

I have a 2008 dodge avenger se and my engine light is on and was flashing before. when it is in drive or park it turns off when i stop. i took it to auto zone and the told me that cylinder 3 and 4 misfire...


The best way to fault find in swap coil 1&2 with coil 3&4. If the fault doesn't change, it is possibly the plugs or something more sinister electrically.

Sep 18, 2017 | 2008 Dodge Avenger

1 Answer

What could cause a 95 dodge avenger to only get spark out of two cylinders when all the plugs, wires, cap, and rotors are new


This could the the coil breaking down, or it could be a bad earth. The coil converts the 12v car battery voltage into a voltage capable of jumping across the gap of a spark plug, in excess of 12,000 volts.
This could be breaking down such that it is unable to provide the continuous voltage required. Are the two spark plugs always the same? If so, what happens if you move them to a position which doesn't spark.
Also, the spark plug will only work if there's a good ground between the plug and the engine block. Oil, dirt and possibly rust will effect the plugs ability to create a spark. Again if you move a 'good' plug to a position which doesn't spark, depending upon the outcome, will point you to the problem.

Oct 12, 2010 | 1995 Dodge Avenger

1 Answer

Replace spark plugs on a 2008 4 cylinder tribute


This is a fairly easy job. Do each cylinder one by one (removal and install), make sure to reinstall the coil on the same exact cylinder (DO NOT MIX UP). 1. Remove coil retaining scre 2. Pull upward on the coil to remove. 3. Remove spark plug (using a spark plug socket). 4. Properly gap new spark plug (if applicable). 5. Apply sprark plug anti-seize compound on plug threads. 6. Install plug. 7. Aplly coil boot grease on the coils' rubber boot tips. 8. Reinstall coil.

May 22, 2010 | 2008 Mazda Tribute

1 Answer

Where are the spark plugs located in a 2008 dodge avenger?


They screw into the engine block. Open the hood and look for wires going to the block. Pull one wire away from the engine block. Below, is the spark plug.

Oct 11, 2009 | 2008 Dodge Avenger

1 Answer

Car is stuck in park.


check the sparking plugs

May 31, 2009 | 2008 Dodge Avenger

4 Answers

2008 dodge avenger spark plug location and socket size.


  • 2008+ Dodge Avenger 2.4L 4cyl.
  • Remove plastic cover on top of engine, just pull on each corner for it is friction fit.
  • Once removed you will see 4 black spark plug covers with one hex type screw holding each.
  • Remove Hex screw and place aside, pull upward to remove plug boot from plug.
  • To remove the plug, use a 5/8 socket with a 6" extension. Once plug has been turned out all the way and you cannot get the plug up and out of the hole, just press the plug boot back on the plug and pull it back up.
  • Gap and replace 4 plugs with the same or equavalent type,. Drop plug down the hole and use socket to align and tighten until just snug, then torque to manufactures specifications.

Feb 14, 2009 | 2008 Dodge Avenger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

834 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

79077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...