Question about Ford Transit Connect

Open Question

Ford transit van 03 central locking not working. Where is fuse 230 located so we can change it if possible to see if thats the reason. Manuel said behind instrument cluster but is this possible?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

BigBlue77
  • 59 Answers

SOURCE: Oil gauge on my instrument panel is not working on my 03 suburban

The bezel around the cluster is just cliped on. You will have to set the parking brake and put the gear selector in 1st gear and pry around the bezel to release the clips. The cluster is held in with 4 7mm screws.

Posted on Sep 06, 2008

  • 341 Answers

SOURCE: instrument cluster removal 2001 buick century

no you have to remove trim most gm you just pull on trim & pops off then remove 4 screws lift out cluster

Posted on Oct 20, 2008

SOURCE: instrument cluster 2001 buick century

It comes off from the front. Open the front passenger side door and remove the fuse panel access door on the right hand side of the dash. There`s 1 screw to remove frome the dash cover and then pull the cover off. It`s easiest to work the top out and then lift up and out. Then there are 4 screws that hold the instrument cluster in place, remove them and pull it out andf you`ll have access to the bulbs.

Once you do it you`ll find you can pull the ****** out in 5 or 10 minutes.

Posted on Nov 07, 2008

tommyboinow
  • 324 Answers

SOURCE: changed the gear box on the ford transit van

did you reset the computer after replacing it?

remove the positive battery cable for 10 mins.....

Posted on Nov 26, 2008

  • 14 Answers

SOURCE: central locking on Ford focus 1.4 W reg 2000

hi i would start by checking if there is a relay, it seems that there is a delay on the pressure pump that is supposed to shoot the door pins up.

Posted on Feb 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Transit Mk7 2004 central locking has gone electrically dead. Where is the fuse for it ? In Mk6 van it is above brake pedal but not in my Mk7


Power locks are controlled through the module known as the BCM, have it scanned to see why the locks are not working.

Jul 13, 2017 | Cars & Trucks

1 Answer

Where is fuse location for central locking on a 2010 ford transit


it might be under the steering column taped to wiring loom, or on a small bracket ir have a look in passenger side footwell for an additional fuse panel different locations for different models/years

Feb 19, 2015 | Ford Cars & Trucks

1 Answer

Ford transit van, where is fuse 83 located.


Look for a fuse box inside the vehicle or outside where the engine is.

Sep 09, 2014 | Cars & Trucks

1 Answer

Sliding side door will not lock


Ok, I had this problem on an 03 Transit connect and it was the actual solenoid in the locking mechanism that had given up the ghost. I removed the unit by taking the inner door panel off. Then unhinging the back of the sliding door near the guide rail side, just to so I could get in closer. Pull the plastic manual locking lever out and undo the three torx screws by the actual lock. The unit comes out as a block and I tested the central locking and the solenoid did nothing. I took the block with me just as a comparison and went down to the local scrappy and got another unit for £20. Probably an hour and a half to do the job but money well spent IMO.
NB; check the central locking plug and socket that marry up when the door is shut are in good order as things can get slammed in there and damage it. The socket is located on the rear door post around passengers seat level height and the plug to your right in the sliding door. A quick check could save you and hour and a half and £20 ;-). Hope this helps.

Jun 13, 2013 | Cars & Trucks

1 Answer

Ford transit central locking


Sounds like you will be spending quite a while at your garage repairing a damaged loom and then sorting the alarm system out. Was it a stolen vehicle that has been recovered I wonder. Check the DVLA records.

Jul 14, 2017 | Cars & Trucks

1 Answer

Ford transit connect central locking


You may have two bare wires touching creating a short. Trace out the wiring. You can get wiring diagram off yahoo.

Jun 11, 2013 | Cars & Trucks

1 Answer

I've locked my keys in my ford transit van 350 2006 can any help


You should be able to unscrew the antenna and slide it between the door and cab. If its too tight you can use a screw driver to gently pry the door open. Although this will depend on where your lock is located.

Mar 11, 2013 | Cars & Trucks

1 Answer

Ford transit swb van central locking


Please provide the question you have about central locking (we call it remote keyless entry).

Jul 11, 2012 | Ford Transit Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

351 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...