Question about Jeep Wrangler

1 Answer

How many pound you torque for jeep wrangler 4 cyl. year 97 head gasket

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 142 Answers

Tightening Sequence

8 - 4 - 1 - 5 - 9
7 - 3 - 2 - 6 - 10

Pass 1 - 22 ft/lbs.
Pass 2 - 45 ft/lbs.
Pass 3 - # 7 - 100 ft/lbs.
Pass 3 - All others - 110 ft/lbs

Posted on May 26, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

98 jeep wrangler tj 4.0 oil pan bolt pattern or layout. An torch specs


Bobby, oil pan bolt torques for 4.0 Wrangler. Oil Pan Bolts 1/4 84 in-lbs Oil Pan Bolts 5/16 132 in-lbs As far as sequence, see last link, start in center, criss cross pattern tighten snug all, then repeat to torque spec.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Oil Pan Gasket leaking
http://jeephorizons.com/tech/99_40l_torque_specs.html
98 jeep 4 0 oil pan bolt torque sequence specs Google Search

May 21, 2016 | Jeep Cars & Trucks

1 Answer

Where is the crank position sensor located on the 2002 Ford Escape? Will I need a rubber O ring or paper spacer?


The Crankshaft Position Sensor (CKP):
4 CYL - located on the front of the engine, near the flywheel end of the block. remove exhaust manifold, disconnect electrical connector, remove bolt. installation is reverse of removal, no gasket req'd. torque to 62 inch-pounds
6 CYL - located next to crankshaft pulley - remove right wheel, remove lower right splashshield. disconnect electrical connector, remove bolt. installation is reverse of removal, no gasket req'd. torque to 89 inch-pounds

Dec 17, 2010 | 2002 Ford Escape

1 Answer

1994 4runner, six cyl. putting rebuilt heads on, toyota head gaskets, new head bolts "tvs 10.9". Torqued bolts in pattern to 33 foot pounds. another 1/4 turn in the pattern. and into my next and final 1/4...


REMOVE 3 BOLTS MAKE SURE YOU HAVE THE RIGHT THREADS.IF BOLTS LOOK OKAY.YOUR BOLTS HOLES HAS DEBRIS OR OIL AND ANTIFREEZE IN THEM.OR YOUR BOLT HOLES IS STRIPPED.YOU HAVE TO REMOVE HEAD TO FIX THE THREAD PROBLEM.IF YOU HAVE NOT MADE THE FINAL TORQUE TO CRUSH AND SEAL HEAD GASKET THE. HEAD GASKET PROBABLY ALRIGHT.YOU HAVE TO LOOSEN HEAD BOLTS IN SEQUENCE BACK OFF A LITTLE AT EACH BOLTS.IF HEAD GASKET LOOK DAMAGE AT BOLT HOLES REPLACE HEAD GASKET.

Nov 13, 2009 | Toyota 4Runner Cars & Trucks

1 Answer

What is the torque setting for a 2.4 4cyclinder jeep engine


Head needs to be "step torqued" first round is at 22 foot pounds, second is at 45 foot pounds, third is 100 foot pounds at passenger side front corner, 100 at all others. sequence is: passenger side: front to rear: 8,4,1,5,9
Drivers side: 7,3,2,6,10 Tighten in numerical order (1,2,3,4, etc).

Sep 22, 2009 | 1991 Jeep Wrangler

2 Answers

What is the tension on cylinder head bolts for a jeep grand cherokee 307935 4 litre, 6 cylinder, 1999, petrol motor.


Coat threads of left hand front bolt with sealant: 1st - step; - 22 ft./lbs. 2nd - step; - 45 ft./lbs. 3rd - step, all bolts except L.H. front bolt; - 110 ft./lbs. 4th - step, L.H. front bolt; - 100 ft./lbs. fig100.png

Sep 05, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Two front cylinders are low


If your going to chg. head gasget, as long as you got the head off you would be smart to have a valve job done too. That could be why you lost compression in the 2 cyls. burnt valves will cause loss of compression. But take note if you elect to have a valve job done you also run the risk of it to start useing oil because of the increase in compression on the oil rings with that many miles it can happen.

Mar 19, 2009 | 1991 Jeep Wrangler

1 Answer

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

1991 jeep cherokee sport 4.0


 For your 1991 Jeep Cherokee 2WD 4.0L MFI :
  Foot pounds (Final torque) 

  Note:
  Torque sequence ------------------  
  front    | 12  8   4   1   5   9  13 | 
  of | | 
  engine | 11  7   3   2   6   10 14 | 
  ------------------  
Final torque must be reached in 3 equal steps  
  Step 1: torque all bolts (except bolt 11)  
  to 110 Ft/Lbs  
  Step 2: torque bolt 11 to 100 Ft/Lbs  
Recheck final torque in sequence  

Sep 30, 2008 | 1991 Jeep Cherokee Briarwood

1 Answer

Radiator problem, I think?


Not likely, but you can flush the entire system, and that would give you an indicator of the condition the engine is in internally. Smell the overflowing coolant, if it has a burned or exhaust like smell, you need to look at your engine gaskets.(Cyl Head gasket) especially. in a worse case scenerio, the heads themselves may need to be looked at. When you get a cracked head, you typically get a condition where the pressure the engine makes, pushes to coolant back through the system end up in the overflow bottle. I love jeeps, so good luck with this repair.

Aug 05, 2008 | 1988 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...