Question about Mazda Protege

Open Question

How to install a sunpro super tach 3 into a 2001 mazda protege mp3 series

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 834 Answers

SOURCE: How do I install a

The Black wire will connect to body ground, and it should be a good solid ground and if this wire is not grounded well then you might receive a primary voltage shock if you touch anything that is metal or grounded inside of the vehicle when the engine is running.

The Red wire should be connected to power when the key is in the "Run" position only, and a good place to find that source is one of the "IGN" connections at the fuse panel using a covered female spade connector. Use a test light and be certain that the connection only has power when the key is in the "Run" position, and has no power when the key is in the "Off" or "Accessory" position.

The White or Yellow wire should connect to the "LPS" connection at the fuse panel next to the LPS fuse using a covered female spade connector.

The Green wire will connect to the "-" negative side of the ignition coil or to the "Tach" or "Test" lead that runs from the negative side of the ignition coil. To locate the lead run down the wire from the negative side of the ignition coil and the lead should break off from that wire and it should have a tag on the wire that will say either "Tach" or "Test" (sometimes it is just an empty black wire connector) and that is if the lead does not come straight off from the wire connector at the ignition coil. If there is no lead you can get a wire tap connector to tap into the wire from the negative side of the ignition coil and then use a covered male spade connector to connect the Green wire from the tachometer to the wire tap connector.

Here is a diagram to help assist you and if you can not download the image right click on the image and then select "save picture as..." or "save image as..." and from your image viewer you should be able to read this diagram or print it out, and let me know if you require any further assistance.


d756391.gif

Posted on Aug 20, 2010

  • 6982 Answers

SOURCE: How do I hook-up Sunpro Super tach 2.

I've got an install diagram for that around here somewhere but for now, the trigger wire to run the tach itself goes to the "tach" connection next to the "Bat" terminal on the distributor cap. one wire attaches to your dash lighting so it comes on with the dash lights and dims properly, the other wire is likely a ground. If I don't add to this later, try googling Sun electronics...I am fairly sure they have an install page.

Posted on Jan 04, 2010

drsinister69
  • 2317 Answers

SOURCE: i1999 dodge ram 1500 5.2 and need to no how to put a tach in

Red wire would go to ignition battery, the black to ground. The third wire, probably green or blue, goes to the negative side of the ignition coil. Is there a wire for dash illumination?

Posted on Mar 10, 2010

Testimonial: "Everything he said was right and thanks."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just bought a sunpro super tach2 and it shows that it is running to fast. whats the problem


There should be 2 adjustments on the back. A switch for 4-6-8 cyl use and a slider to fine tune the rpm. If you know your car idles at 750rpm, move the slider until the tach reads 750. The switch for cylinder numbers should be self-explanatory and must be set first.

Feb 12, 2015 | Cars & Trucks

1 Answer

I have a sunpro after market tach. i need the color coded diagram to install it,can anyone help me?thanx


Tried going to sunpro online? paste this in and it should get you there:http://www.google.com/search?q=sunpro+tachometer+wiring&ie=utf-8&oe=utf-8&aq=t&rls=org.mozilla:en-US Ive always found that going to the source is better than getting it second-hand.

Apr 23, 2010 | Chevrolet Silverado Cars & Trucks

1 Answer

I want to install an aftermarket tachometer in a 1997 Mazda Protege Dx, which does not utilize a coil in it's ignition system. Anyone knows where to get the signal from? Thanks!


some tachs can take the signal from one of the spark plug wires; you just thread the wire into the bood with the plug, or into the other end of the spark plug wire.

Mar 31, 2010 | 1997 Mazda Protege

1 Answer

I1999 dodge ram 1500 5.2 and need to no how to put a tach in


Red wire would go to ignition battery, the black to ground. The third wire, probably green or blue, goes to the negative side of the ignition coil. Is there a wire for dash illumination?

Mar 10, 2010 | 1998 Dodge Ram 1500 4WD

2 Answers

How do I hook-up Sunpro Super tach 2. Wires: 1 each - green, red, white, and black? Or in general how do these type tachometers hook-up?


I've got an install diagram for that around here somewhere but for now, the trigger wire to run the tach itself goes to the "tach" connection next to the "Bat" terminal on the distributor cap. one wire attaches to your dash lighting so it comes on with the dash lights and dims properly, the other wire is likely a ground. If I don't add to this later, try googling Sun electronics...I am fairly sure they have an install page.

Jan 04, 2010 | 1985 Chevrolet K1500

1 Answer

I'm looking for the gap required in the spark plugs for my Mazda MP3.


Make: MAZDA
Model: PROTEGE - MP3
Year: 2001
Engine: L4 - 2.0L - FI - - GAS

Brand: Champion
Product Name: Traditional Spark Plug
Part Number: RC12Mc-4
GAP: .044"
Notes: w/DOHC (Original Equipment Manufacturer and/or Original Equipment Equivalent)

More details: Champion Spark Plug

I hope help you whit this (remember rated this help).

Sep 10, 2009 | 2001 Mazda Protege

1 Answer

I have a 1994 GMC Sonoma SL and it doesn't have a tach in it, so I brought one made by Sunpro. And my problem is I've never hooked one up. So is there anybody out there that can tell me how to do it? and...


Do you have the instructions that came with it? If not, you can get them online at the sunpro website:
http://www.sunpro.com/user_manuals.php
If you need more help, let me know

Aug 09, 2009 | GMC Sonoma Cars & Trucks

1 Answer

How to replace knock senor switch on 2002 mazda protege 5



Removal & Installation

  1. Disconnect the negative battery cable.
  2. Remove the intake manifold.
  3. Disconnect the sensor connector.
  4. Remove the sensor from the engine block.
  5. Installation is the reverse of the removal procedure.

    0900c1528019fa95.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Knock sensor removal and installation-Mazda 3

  1. Disconnect the negative battery cable.
  2. Remove the intake manifold bracket.
  3. Disconnect the sensor connector.
  4. Remove the sensor from the engine block using special tool 49H018001 or equivalent.
  5. Installation is the reverse of the removal procedure.

    0900c1528019fa96.jpg enlarge_icon.gifenlarge_tooltip.gif GL G

May 09, 2009 | 2002 Mazda Protege

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...