Question about 2003 Chrysler Town & Country

1 Answer

A/C Blower Switch on chrysler----- Blower works in

A/C Blower Switch on chrysler----- Blower works in the "MAX" position but does not work in the other positions...... ALSO, The back seat controls work the same way as the frount controls.

Posted by on

  • jr heath May 28, 2011

    The BLOWER MOTOR?WHEEL ASSEMBLY is located behind the Glove Compartment. Very simple to get to.....

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 142 Answers

Chrysler vehicles are notorious for the blower motor resistor going out. If your Town & Country has automatic climate control use a SMP RU399, else use an SMP RU362 for the front resistor and a SMP RU490 for the rear. They are generally located on top of the blower motor/wheel assemblies.

Posted on May 26, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What needs replacing when my blower motor only works in the 2nd and 3rd position on my 2005 Chrysler town and country?


You would need to perform the diagnostics to pin down the cause. It could be the dash switch or burned wiring connector to the switch.

Oct 13, 2016 | 2005 Chrysler Town & Country

1 Answer

Why does my heater motor stays on controls don't work 94 chrysler?


sounds like you have a blower motor resistor that has gone bad. these systems are set up(wired) that the blower will either not work, caused by the main resistor wire is broken, or will only run on high. you don`t say exactly what is your problem. it could also be a bad switch that has gone bad and won`t shut off(always in the run position) due to a short.

Jun 01, 2014 | 1994 Chrysler New Yorker

2 Answers

I just replaced the actuator on my 2000 Chrysler Concorde LXI and my heater still isn't working. Any other idea's?


If its not blowing air then you may want to try a new blower motor if it is blowing air then you probably need a new thermostat

Jan 23, 2013 | Cars & Trucks

1 Answer

Max a/c Assist????


The vacuum control switch is leaking.

Mar 24, 2017 | Cars & Trucks

1 Answer

Climate control system has been working on and off for the past few months. It used to always work when the ignition was in the "on position." But when you start the car, it didn't work. Now...


All signs are pointing to the electrical portion of the ignition switch AND / OR the wiring connection.

The electric switch is located directly behind the key switch (under the steering wheel).


I recommend you to remove the battery cable first to prevent accidental air bag deployment.


Inspect the connector for damage or wire(s) got pull out of the socket,

Sep 05, 2011 | 2004 Buick Regal

1 Answer

My blower only works 1 through 4 and will not work on the highest position number 5


{: ) Check out the J-case fuse (square) labeled BLWR 40amps at the underhood fuseblock. This fuse is the source of power to the blower motor when position 5(max speed) is selected. If this fuse is tested to be okay, you need to access for the blower resistor connectors. Turn ignition on, and set blower to max speed (#5). Probe on the blower resistor terminal (orange wire) and you should get 12volts, also probe the terminal (red wire) which came from the 40amp fuse. 12v should be present on these two terminals at the blower resistor when at max blower speed. Particularly on the orange wire, if you don't get 12volts when at #5 position, it 's probable that the blower speed control switch is faulty. But if you did got 12volts during the procedure, then you should replace the blower motor resistor. Goodluck.

Jul 24, 2011 | 2006 GMC Envoy

1 Answer

2002 chrysler town&country blower motor will not turn off is always on ?? fan speed does not work ??? defrost; floor vent modes still work air is directed to this positions if selected. blower motor...


your switch is not working, may be a bad switch or wires, disconnect switch, make sure you label wires. start car blower should not work, buy new switch and it should fix the problem

Oct 13, 2010 | 2002 Chrysler Town & Country

1 Answer

The #4 position of the ac/heater blower fan switch does not work could it be resistor or switch"how do you replace part?


this would be caused by the switch, the resistor gives you one speed and that would be high which is #4

Jun 22, 2010 | 2000 Chrysler Town & Country

2 Answers

My AC was first only working at the max setting now not at all


go for the reostat which is all in one with the blower motor ,expensive part though

Jun 03, 2010 | 2002 Pontiac Grand Prix

2 Answers

Blower is working on position 4 (max) only


The fan speed control resistor is burned out.

Nov 23, 2008 | 2000 Nissan Quest

Not finding what you are looking for?
2003 Chrysler Town & Country Logo

623 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...