Question about 2005 Chevrolet Colorado

Open Question

Where is the MAP sensor on a 2005 Chevy colorado 2.8L

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 51 Answers

SOURCE: 2005 chevy colorado runs rough and gets bad gas mileage.

Sounds like it needs spark plugs and wires, and a fuel system treatment.

Posted on Oct 08, 2008

polarcycle
  • 1392 Answers

SOURCE: 2005 chevy colorado abs fault

Sounds like water getting in one of the connectors. You will need to see what fault code is in there when the light comes on, then look at that sensor.

Posted on Jun 05, 2009

matney68
  • 426 Answers

SOURCE: chevy colorado loss of power

take it to local parts store that scans for codes for free, you will get a print out with any codes that are set and go from there

Posted on Jul 30, 2009

c17hydro
  • 2984 Answers

SOURCE: how do i change out the knock sensor on a 2006 chevy colorado

You didn't list your engine size so please pick the applicable to your motor size:

Removal & Installation 2.8L & 2.9L Engines To Remove:

  1. Lift the vehicle high enough to gain access to the knock sensor (KS) through the left front wheelhouse.
  2. Remove the left front wheel and wheelhouse liner.
Knock sensor (KS) (A), Engine harness (B), Knock sensor (KS) connector (C)


e44e83f.gif
  1. Disconnect the knock sensor (KS) connector.
  2. Detach the knock sensor (KS) from the engine block.
To Install:
  1. Attach the knock sensor (KS) to the engine block.
    • Tighten the bolt to 18 ft lbs (25 Nm).
  2. Connect the knock sensor (KS) connector.
  3. Install the left front wheelhouse liner and wheel.
  4. Fully lower the vehicle.

Posted on Sep 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2005 chevy colorado ive change the map senser twice and it still not running like it should wat else could it be


Go to Auto Zone and they will provide a FREE scan of the engines computer and tell you what the fault is and how much it will cost to buy the part

Jul 10, 2010 | 2005 Chevrolet Colorado

1 Answer

2005 chevy colorado whole frnt left side lights


The inside light is blinking quickly because the front blinker light is out. I'm afraid that without more info I can't tell you why the lights are out.

Jun 26, 2010 | 2005 Chevrolet Colorado

1 Answer

Transmission fluid for 2005 Chevy Colorado


You would need to find something that is the same as sychromesh fluid that GM uses.

May 03, 2010 | 2005 Chevrolet Colorado

1 Answer

Where are the cam sensors (2) located on my 2005 chevy colorado


I have a 2005 and the things that go bad on it is when the sensor goes off then for the intake then where the butterfly is on the intake gets dirty and needs to be cleaned it is the venturi gets dirty and needs to be cleaned and if it is a cam crank then it is the cam actuator that needs fixed you can tell if you take it off and there a screen missing it is a good sign that it needs be replaced and it is on the left side of the engine you need to understand that if it gives you a code that tells you that it is a sensor that is telling you that what the sensor looks after is bad not the sensor

Apr 11, 2010 | 2005 Chevrolet Colorado

2 Answers

Chevy colorado fault light reset


The only way to clear the check engine light is with a scan tool.Disconnecting battery will not clear codes.Hope this helps.Good luck.

Apr 08, 2010 | 2005 Chevrolet Colorado

1 Answer

2005 chevy colorado abs fault


Sounds like water getting in one of the connectors. You will need to see what fault code is in there when the light comes on, then look at that sensor.

Jun 05, 2009 | 2005 Chevrolet Colorado

1 Answer

2005 Chevy Colorado edit


If you put the tail gate down, there is 2 screw (phillips) that holds the tail light in place. Remove them & you can twist the bulb out. Thats it, put back together in reverse. Hope this helps.

May 21, 2009 | 2005 Chevrolet Colorado

2 Answers

2005 chevy colorado runs rough and gets bad gas mileage.


Sounds like it needs spark plugs and wires, and a fuel system treatment.

Aug 13, 2008 | 2005 Chevrolet Colorado

Not finding what you are looking for?
2005 Chevrolet Colorado Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...