Need torque settings for front wheel bearing axle nut

1995 C1500 spindle nut torque procedure? - CK5 Network

https://ck5.com > ... > General Discussion > The Garage
Jan 31, 2005 - while rotating the hub in a foward direction torque the nut to about 12ft lbs. Keep doing that a few times to ensure the bearings are seated.

96 gmc: torque..the front spindle nut..C1500 - JustAnswer

https://www.justanswer.com > Car Questions > GM Repair
Sept 16, 2011 - Torque nut (12) 10-12 ft lbs while turning the wheel assembly forward by hand. This will seat the bearing. Loosen nut (12) to a just loose ...
1 answer · Top answer: You can attach the magnetic base to the end of the spindle or to the brake caliper bracket. ...

• 
  

  1996 chevy: the torque setting for front wheel bearing..1500 4x4

  https://www.justanswer.com > chevy > 1tv6x-1996-che...
  Feb 18, 2009 - Outer Tie Rod Nut (C and K Models) · Shackle to Frame Nut and Bolt (C3500HD) · Shock Absorber Nuts (K Models) ; 62 N·m · 95 N·m · 90 N·m ; 46 lb ft.

Torque specification guide - PDF4PRO

https://pdf4pro.com > cdn > torque-specification-...
PDF
Front and rear axle nut torque specifications for FWD, RWD and 4 W/D vehicles. Torque specification guide. Form #457377. April, 2007.

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow

2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...

Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..

i usually put lock tight blue on them and tore to 65 ft lbs the nut on the axle i usually tore to 50- 60 ft lbs no lock tight

the four axle nuts, 98 ft lbs, tighten in criss-cross pattern.
The hub nut/wheel bearing, 148 ft lbs, use new nut, don't let vehicle weight sit on the ground while torqueing, it could damage the wheel bearing.
If I left something out, give me a holler.

if its not a drive axle and only has a castle nut with a cotter pin , then regrease the wheel bearings and run nut all the way in to its hand wrench tight (not impact gun), turn wheel one or two full turns to seat it , then back castle nut off two spaces and install cotter pin , this s\is std way to set proper spacing on wheel bearings

if its a drive axle consult your cars model and make and year torque specs book

The axle nut is 118 ft lbs
The other 3 bolts are a 75 ft lbs

Front wheel bearing hub is 147 ft lbs. Axle nut is 170 ft lbs.

The front wheel bearing is a hub and bearing assembly. To remove you will.... 1. Remove the tire 2. Remove the axle nut. You can put a punch in the fins of the rotor to keep the assembly from turning while you rmove the nut. You can can do the same thing when you torque the axle nut. 3. Remove the caliper and rotor. 4. Unplug the abs sensor if equipped. 5. Remove the three bolts that hold the hub to the knuckle. 6. Rmove the hub. If you need torque specs let me know and i'll get them for you. It is absolutely critical that you torque the axle nut to the proper spec!

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

TO REMOVE FRONT WHEEL BEARING.YOU NEED TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE SITTING ON LEVEL SOLID GROUND.BEFORE RAISING VECHICLE OFF GROUND YOU NEED TO LOOSEN HALF SHAFT AXLE NUT JUST A LITTLE BECAUSE WHEEL IN THE AIR HARD TO LOOSEN AXLE NUT WHEN YOU HAVE HOLD THE WHEEL WHILE LOOSEN THE AXLE NUT WHICH IS TORQUE ON ABOUT 200 FT LBS.USING A SIX POINT AXLE SOCKET SOCKET SIZE COULD BE 34 OR 35 METRIC 1/2 INCH SOCKET.YOU NEED 1/2 INCH BREAKER BAR.ONCE YOU LOOSEN AXLE NUT A LITTLE THEN RAISE VECHICLE THEN REMOVE WHEEL.THEN FINISHING REMOVING AXLE NUT AND WASHER.THEN REMOVE THE CALIPER FROM THE STEERING KNUCKLE AND SUPPORT IT ASIDE USING A PIECE OF WIRE.REMOVE BRAKE ROTOR.THEN REMOVE THE 3 HUB BEARING ASSEMBLY BOLTS. USE A SWIVEL SOCKET GOING TO BE HARD TO REACH SPOT WITH A REGULAR SOCKET. REMOVE THE HALF SHAFT FROM THE HUB BEARING ASSEMBLY.REMOVE HUB AND BEARING ASSEMBLY. PUT EVERY THING BACK VISA VERSA. TORQUE HUB BEARING BOLTS TO 70 FT LBS. TORQUE AXLE NUT 284 FT LBS IF YOUR CAR IS 1998 MODEL AND TORQUE AXLE NUT 100 FT LBS FOR THE 1999 TO 2001 MODELS.THE WHEEL HAS TO BE ON THE GROUND JUST ENOUGH TO KEEP IT FROM TURNING.DONT LET ALL THE CAR WEIGHT DOWN UNTIL YOU HAVE TORQUE WHEEL TO THE RIGHT TORQUE.LET ME KNOW IF YOU HAVE ANY PROBLEMS.

TOOLS YOU NEED IS 35 METRIC SOCKET FOR AXLE NUT.USE 6 POINT SOCKET.DONT USE 12 POINT SOCKET.COULD DAMAGE AXLE BOLT EDGES.MAKING IT HARD TO GET OFF.YOU NEED A TORQUE WRENCH WITH THE RANGE OF 200 FT LBS TORQUE.YOU NEED 1/2 BREAK BAR.AND A HUB PULLER.NOW TO LOOSEN AXLE NUT.BEST TO LEAVE TIRE ON WITH CAR WEIGHT ON GROUND TO LOOSEN THE AXLE.BECAUSE ITS GOT 192 FT LBS TORQUE.HARD TO LOOSEN WITH TIRE OFF.192 FT LBS TORQUE IS WHAT YOU TORQUE IT AT.BESURE TO READ INSTRUCTIONS TO NEW HUB BEARING ASSEMBLY. YOUR AXLE NUT TORQUE WILL BE DIFFERENT IF YOU GET A NEW GREY NUT.BECAUSE NUT STRENGHT WILL BE DIFFERENT.IF YOU GET A BLACK NUT WHICH IS HARDER STEEL TORQUE WILL BE 192 FT LBS.YOU NEED A 13 METRIC SWIVEL SOCKET TO GET HUB BEARING BOLTS OFF THEY WILL BE IMPOSSIBLE TO REACH WITH OUT IT.HUB BEARING BOLTS TORQUE IS 62 FT LBS