Question about Dodge Challenger

1 Answer

How do i remove the ign. sw. from a 1973 dodge challenger?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 184 Answers

Pull the steering wheel. Remove the column cover and there is a spring band round the ignition mechanical part which when raised releases it. They also had an internal spring design which had a small hole in the casing.- put a punch in the hole and remove the tumblers with the key turned to accessories. The electrical was held on with a small screw.

Posted on May 26, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

50A IGN Starter SW/ Starter fuse blows every time I start the vehicle


Run a jumper from the fuse connection to the starter

Nov 13, 2015 | 1998 Dodge Durango

1 Answer

When i turn key off it continues to try and start and eventually runs battery down


Jeffs solution (above) is for a different problem. If the Starter Motor continues to turn with the Ign. Sw. off, yours won't be a Starter Motor problem. However, the most likely cause is either the wire to the Starter Solinoid or the Solinoid itself.

I can't see the alternator being the cause either, as suggested above.
.
Try this
Disconnect the thin wire from the Solinoid (this is the one that activates the Starter when you turn the key).
With the battery charged, the Starter shouldn't work. Put the wire back and try again. If the same problem is there, quickly remove the wire.
One of 2 things will happen:-
1: The Starter will stop. The cause is in the wire to the Ign. Sw. or the Ign. Sw.
2: The Starter will continue turning. Repair or replace the Solinoid.

Mar 17, 2014 | 1997 Isuzu Rodeo

2 Answers

I have a 2004 dodge durango that is getting a p700 wiring tcm code do you now what the problem could be


this code is related to the EATX controller.this is the trans computer system = trans shop? ceck for loss connection in the wiring going to the terans. but these may be difficult to get to..

Feb 17, 2010 | 2005 Jeep Grand Cherokee

2 Answers

I want to take apart the front suspension on my 1973 dodge challenger . I'm looking for a diagram showing the complete front suspension parts .So I don't get lost putting it back together later and a parts...


You might be better off with a digital camera, and take your own pictures of the areas that you think may cause you to scratch your head later when re-assembling. Once on your computer, you can zoom or whatever as needed. If that's not an option, get back to me/us, and we'll dig a little harder and see what we can find.

Dec 05, 2009 | Dodge Challenger Cars & Trucks

1 Answer

How to change ignition switch on a 92 4w drive k1500 series truck, manual transmission


When you say ign sw,do you mean the key and tumbler or the ign sw under the dash?
the key and tumbler needs the steering wheel removed then you will clearly see a small screw remove it and the switch slides out.
Now if under,remove the knee bolster and you will see the switch on the side of the steering column tahe the two wire harness out remove the two screws and reverse for install.

Aug 27, 2009 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

I am rebuilding a 1973 360 cu in Dodge engine and can't find the right pulley for water pump with no AC. Can you steer me in the right direction to find it?


80 challenger was my project i went with www.car-part.com they had almost everthing some stuff came from jegs.good luck you will love her when shes done.

Jun 10, 2009 | 1983 Dodge Challenger

1 Answer

No brake lights


could poss be multi-switch

Jul 31, 2008 | 1995 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75824 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...