Question about Honda Fit
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
the filter is behind the glove box. pull the 2 clips on both sides of glove box. then remove glove box. the filter cover should be right there and just unclip the cover and replace filter.
Posted on Jan 19, 2009
I'm going to send you exploded view of the glove box and the in cabin micro filter cover illustration. Remove the two upper screws on the glove box and carefully pry metal clips loose.
Disconnect glove box lamp electrical connector. Do not let glove box assembly hang from glove box lamp harness.
Remove three lower screws and remove damper clip from glove box door. Separate glove box housing and passenger instrument lower panel.
Remove three screws and remove in cabin micro filter cover.
Remove in cabin micro filters from front heater and cooling unit assembly.
Note When installing two new in cabin micro filters ensure that the filters are facing in the direction indicated by the direction arrow for the airflow. Direction arrow is printed on side of in cabin micro filters.
Install in cabin micro filter cover. Reinstall glove box.
Posted on Oct 10, 2009
Testimonial: "Finaly I found the air flow door with three screws and removed it. The filter will need replacement soon. It is been replaced one time at the dealer."
Take everything out of the glove box on the passenger side. Squeeze the black clips on either side of the glove box interior to free it from its retainer and pull it toward you. It will glide forward on hinged arms. Lower it as much as possible so it's out of your way.
Posted on Dec 06, 2009
This solution pertains to a 2008 Honda Pilot...To replace the cabin air filter which is located on the passenger side of the vehicle behind the glove box: Open glove box and remove stored items...while sitting in the passenger seat, pull towards you on each of the two clips on the left and right side of the glove box...this will cause them to become loose and the glove box will tip out completely exposing the inside of the dashboard. (Alternately...carefully pull towards you on the top center of the glove box which will cause the left and right side stops to pull away from the edges and allow the glove box to tip out) Here it gets tricky...the box holding the cartridge for the cabin air filter is the large black box on the left side behind the glove box The filter fits in a removable tray vertically inside that box. A pressure clip at the top of the box allows the vertical cover to be removed exposing the tray with the Cabin air filter... BUT!!! There is a plastic bar an inch or so high which has been placed there by the manufacturer to prevent most from changing the filter without the service department being involved. This bar must be cut with a sharp sheetrock knife or hacksaw and discarded, (it will not be reinstalled). Then there is a flat metal bar behind the plastic bar that can be removed using an 8mm socket and a phillips screwdriver. There are 2 8mm screws and one phillips head screw on each side that must be removed in order to remove the metal bar. THEN you can remove the cover to the cabin air filter box, pull out the tray with the filter (note how the filter is in the box so the new one can be placed the same way) reinsert the tray with the new filter and replace the tray cover. All other steps to finish the job are obvious as everything is the reverse. Actually the whole process is a lot of trouble and unless you are determined to change the filter I would recommend not doing it.
Posted on Apr 01, 2010
1.remove the glove box. 2.Cut the plastic cross brace in the glove box opening with diagonal cutters in the area shown, and discard it. 3. Remove the bolts, the srews, and the glove box frame. 4. remove the filter lid from the evaporator, then pull out the dust and pollen filter.
Posted on Jun 20, 2010
Tips for a great answer:
Sep 20, 2014 | Cars & Trucks
Mar 13, 2011 | 2007 Audi A6 Avant Wagon
Feb 21, 2011 | 2007 Honda Ridgeline
Feb 19, 2011 | 2007 Honda Accord Sedan
Feb 26, 2010 | Honda Odyssey Cars & Trucks
Dec 05, 2009 | 2007 Honda Pilot
Sep 27, 2009 | 2007 Honda Accord Sedan
Jul 09, 2009 | 2007 Honda Odyssey
Apr 03, 2009 | 2005 Honda Odyssey
Nov 03, 2008 | 2007 Honda Accord Sedan
103 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: