Question about 1998 Honda Accord

1 Answer

Trying to replace thermostat on a gonda accord LV v6. remove two hoses. assumes the thermostat was in one of them. I was wrong. Do I need to remove both hoses to replace the thermostat. And I keep reading about a bleeding valve? Where is it located. and where is the drain plug. Nedeed visual eamples alomg with instructions.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,116 Answers

Drain about 1 gallon of coolant from radiator Follow upper radiator hose to engine should end at housing secured to engine by 2 or 3 bolts Remove housing make note how thermostat is installed in housing Clean both surfaces completely Install new gasket and thermostat secure housing evenly to engine re-fill radiator Start engine and check for leaks Bring engine up to normal operating temperature with heater on Re-check coolant level

Posted on May 26, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How too change the thermostat on a izuso rodeo v6


but first it has to want to change,?,,,, LOL.....

well you can youtube and see 10,000 folks doing this....
all are same, only the exact spot varies.
what V6 , which size? use real engine names. and no year stated !!
1: drain coolant from bottom of RAD (drain plug or pull hose there)
2: remove hose from thermoatat housing, this is the gets hot first hose to Rad.
3: unbolt , housing
4: remove and replace thermostat, not getting it backwards, or failing to get bleed hole (aka. jiggle pin) up hill.
5: reassemble the housing with proper sealant or gaskets the match you unstated engine. nor year,


v6 2.8L
V6 3.1L 3.2. 3.5L
V6 GM 4.3 (1996 started) FIVE V6's

1991 to 2004 , lots of Rodeos....
the newer rodeos had this lineup.

Mar 18, 2015 | Isuzu Rodeo Cars & Trucks

1 Answer

Thermostat location


According to the book, the 4 cyl and V6 engines have the thermostat under the outlet at the end of the upper radiator hose. Nothing said about a power steering pump being in the area.

Jul 05, 2012 | Ford Cars & Trucks

1 Answer

Changing a thermastat on a 2003 Caravan


the 1993 caravan had two engines offered a 2.5L 4cylinder and a 3.3L v6........on the 2.5L the thermostat is located on the front of the cylinder head were the top radiator hose attach's.
remove the top hose were it attach's to the thermostat housing and the remove the thermostat housing and lift out the thermostat and replace with the new one making sure the spring on the thermostat is facing the engine replace the thermostat housing and top radiator hose and remove the bleeder screw from the top of the thermostat housing and fill radiator with new antifreeze. when you see antifreeze coming out the bleeder hole replace the bleeder screw.

The 3.3L v6 also has the thermostat at the front of the cylinder head were the top radiator hose attach's the thermostat housing the procher is the same except for bleeding the radiator, to bleed the cooling system remove the coolant temp. sensor it is located just below the thermostat housing and fill radiator with new antifreeze until the antifreeze starts coming out the coolent tempt sensor hole them reinstall the sensor and top of radiator.........GOOD LUCK

Dec 09, 2010 | 2003 Dodge Caravan

1 Answer

I can't find the thermostat of a Honda Accord 1995 ex v6


Follow top radiator hose to engine, The neck the hose connects to is the thermostat housing, Remove the bolts and replace as needed

Jun 19, 2010 | 1995 Honda Accord

2 Answers

1993 toyota camry change thermostat


You're going to lose some coolant, so have a bucket or other container ready. Follow the upper radiator hose to the point where it's connected to the engine. The hose is clamped to a metal housing which is bolted to the engine. Remove the bolts (not the hose) and lift the housing to expose the thermostat (may require a little prying with a screwdriver or similar tool). Note how the old thermostat is fitted (which end is up), lift it out of the engine, and then remove all traces of gasket from the housing and the engine. Install the new thermostat and gasket, replace the bolts, add coolant as necessary, and you're done.

Nov 05, 2009 | 1993 Toyota Camry V6

1 Answer

1993 Honda Accord No Heat/Defrost


You will have to drain the radiator. Drain at bottom.
Then, follow the top radiator hose back to where it connects to the engine.
The part with the two bolts in it that the hose connects to is the thermostat housing.
You may have to remove the hose in order to remove the housing.
When you have removed the housing, note the position of the thermostat before you remove it.
When installing, use new gasket, etc.
(you might be able to get away with not removing the radiator hose, but it is recommended)
Be prepared for a bit of spillage when you remove the housing.

Oct 15, 2009 | 1993 Honda Accord

1 Answer

Change thermostat on gm 3400 v6


Drain coolant at the radiator drain. Remove air intake hose and MAF sensor assembly. remove throttle cable bracket and disconnect cable linkage. Remove throttle body bolts and disconnect coolant hoses to throttle body. Loosen heater hose pipe and remove heater hose from rear of pipe. Remove radiator hose from thermostat housing. Remove top thermostat housing bolt. Loosen and almost remove lower thermostat bolt. You will need to slide your wrench and hand under the exhaust crossover pipe to gain access. Loosen the bolt until you can remove the thermostat housing, it should be slotted to clear the bolt. Replace the thermostat and reassemble. Bleed cooling system using the two bleed screws (one on thermostat housing and the other on the passenger side of the engine where the heater hose pipe comes out above the water pump.

Jan 23, 2009 | 2003 Pontiac Montana

1 Answer

Thermostat location on a 1994 honda accord


U should be able to Follow the upper radiator hose to the engine. The hose will be clamped onto the thermostat housing, remove hose clamp, remove hose, remove 2 bolts attaching housing to engine, inside is your thermostat, be sure to install new one in same direction, ( engine will overheat if it's installed backwards. Let me know how u do.

Nov 16, 2008 | 1994 Honda Accord

3 Answers

Thermostat jammed, car overheating


Probably right between the two banks of cylinders, at the front of the V behind the top of the timing case. Not worked on this engine in particular but thats where they usually are on V6's.

Oct 06, 2008 | 1992 Audi 80

2 Answers

Need to know how to change my thermostat on a 2002 mazda 626


The thermostat on the 2002 Mazda 626 2.5 liter V6 is located at the opposite end of the lower radiator hose (near the block). It is nestled between the air-cleaner assembly and the intake manifold (on the driver side). You have to first remove the air-cleaner housing (The top half has several things attached to it; you don't have to completely remove the top half - just sort of move it aside after it hans been unencumbered; the bottom half must be completely removed as this is the area you will be working in.) The thermostat housings' top half can then be ubolted from the bottom half but you can not remove it or pull it aside to gain access to the actual thermostat until you unbolt the ignition coil pack. Mazda uses a strange metal sleeve to protect the lower radiator hose (I assume that's what it's for). There are three bolts holding the pack on (if I remember correctly, two of them hold the sleeve in place as well). After you free the sleeve you can then move the thermostat housings' top half aside and pull the thermostat out. Good luck putting it all back together - it's sort of like a jigsaw puzzle. BTW this is by far the hardest thermo I've ever had to replace.

Sep 16, 2008 | 2002 Mazda 626

Not finding what you are looking for?
1998 Honda Accord Logo

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...