Question about Mitsubishi Lancer

1 Answer

I need to do compression testing on my Delica 4M40 engine. Could any one tell me what the compression rate is?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Mitsubishi Master
  • 1,049 Answers

It's simply the total volume of the cylinder and combustion chamber above the piston at the bottom of its travel (referred to as bottom dead center [BDC]), divided by the combustion chamber volume above the piston at top dead center (TDC).
Why is knowing your true compression ratio that important? With today's lower-octane grades of gasoline, it's important not to exceed known maximum allowable compression ratios for various engines or you may experience detonation that will quickly destroy your engine.
here you can get more technical informations about testers on www.chinasinoy.com

Posted on May 26, 2011

  • fishayato May 26, 2011

    Hey thanks for trying... but you didn't answer my question.
    If it wasn't important I wouldn't look for it.
    Beside 4M40 is a diesel motor!!!

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My mitsubishi delica space gear is misfiring and we can find the problem


what parts have you replaced so far
can be simple or more electronic fualt
to the distributor cap to the coil
that delica has fault codes
if no better
then do a compression test see if it is valves

Feb 24, 2016 | Mitsubishi Cars & Trucks

1 Answer

Need some wiring diagrams of Fuel pump controlled electronically on a 4M40 DELICA engine. Or some manual for this type of engine.


Most of these Japanese cars use a DENSO fuel pump. The fuel pump is attached to the primary circuit... the same one that starts your car mate. The wiring on these things seldom goes sour. It could be your fuel pump relay or the fuel pump itself. Sorry I can't assist further... Go PIES!

Mar 21, 2015 | Cars & Trucks

1 Answer

What do I have to take into account to exchange from a electronic fuel pump to a mechanical fuel pumplease on a 4m40 delica engine.


I don't see any way to do this, since the mechanical pumps are normally engine driven by a lobe on the crankshaft, unless this engine has that functionality built into it. Let me know if you figure out a way!

Mar 21, 2015 | Cars & Trucks

1 Answer

Can 4d56 engine fit in a 4m40 frame?


Probably, but why would you do this? The 4d56 is 2.5L, the 4m40 is 2.8L, some come with a turbo. You would have a loss of performance, and have all sorts of issues with fabricating bits and pieces to make it fit, plus all the injection and control issues.

Oct 08, 2014 | 1996 Mitsubishi Delica

3 Answers

I have a 1994 2.8ltr Diesel (4M40 Mtr), Delica, that conks out


try changing all the heater plugs there are warn out by now,,if it realy dont like starting up on cold days do what i do,,, give it twice the heat up time,,,,,
turn on the kye wate till the heater light go's out then quikly switch it off and turn it back on for a re-heat before trying to start it up,,,also try changing the glow plug heater relay,, it should hold the glow plug heaters on for about 30 seconds after the light has gone off even if the engen has started and is running
but i bet its not doing this? giving twice the heat takes less out the battery than cranking it over and your not wearing out the starter as well?
doing this to my old girl gets her going every time!!!!!

Oct 26, 2009 | Mitsubishi Passenger Cars & Trucks

1 Answer

I am refitting new injectors to my 2.8 diesel 4m40 engine. what is tehe torque setting for these please


55nm for injection nossil and 40nm for injection nossil to body and 5nm for injection clamp nut , these spec's i downloaded from delica club for 4m40 motor

hope this helps , there are many do it youself manuals available from this site including fuel pump diagarams and injection instalation and removal . good luck

Sep 14, 2009 | Mitsubishi Minivan Cars & Trucks

2 Answers

98 mitzi l200 2.8 l eng 4M40


White smoke is a sign of unburnt diesel fuel, check your glowplugs as thats the most common cause when starting .It will start but not hot enough to burn fuel at start up, also check glowplug relay if not the plugs
Delica Owner 4m40

Aug 07, 2008 | Mitsubishi Pickup Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

303 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...