Question about Cadillac DeVille

1 Answer

I have lost a diamond ring between the drivers seat and the center console. Can not find at all. Need to remove the console and look for ring and then replace the console again. Thank you

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 638 Answers

Try taking a magnetic retrieving tool, you can buy these at your local auto part stores, they have a magnet on the opposite end of the tool, then insert the tool between the console , and hoping that it will pick up the ring, and it should come out of the area , of where it is. then you won't have to remove the console.

Posted on May 26, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm an idiot and put my engagement ring in my change holder in my 2006 Chrysler Pacifica. When I went to put it back on, it was no where to be found. I believe it slipped behind the small crack


Print I hope this helps you,good luck.Randy


Removal & Installation

Instrument Panel

  1. Disconnect and isolate the battery negative cable.
  2. Remove the center console closeout panel by removing the left and right attaching screws, then the left and right panels.
  3. Remove or disconnect the following:

    Remove the shift bezel. Remove the transmission range indicator surround bezel. Remove the two screws attaching the front floor console to the lower instrument panel. Open the cup holder and remove the two attaching screws on the bottom of the cup holder. Open the bin and remove the two attaching screws on the bottom of the bin. Remove the front floor console sidewall attaching screws, three per side. Raise the front floor console and disconnect the wiring harness. Remove the front floor console from the vehicle.

    0996b43f807cb4f3.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of front floor console and shift bezel


    0996b43f807cb4f4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of front floor console, showing attaching screws

  4. Remove the floor console base assembly by removing the two screws attaching the L-brackets to the instrument panel.
  5. Remove the nuts attaching the floor braces to the instrument panel.

    0996b43f807cb4f5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of floor brace, attaching nuts, center brace, and floor bracket

May 02, 2012 | 2006 Chrysler Pacifica

1 Answer

Need to remove center console to replace seat belt. After removing 12 screws, console is still firmly in place. What else has to be done?


  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest from the floor console.
  2. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  3. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  4. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  5. Lift the floor console from the front and rear console panel mounting brackets.

Feb 27, 2011 | 1996 Ford Explorer

1 Answer

Ford explorer no heat clicking in dash


NO NEED TO REMOVE WHOLE DASHBOARD!!! REMOVE TWO7MM SCREWS FROM THE BOTTOM OF STEERING PANEL & PRY AND REMOVE PANEL.
NEXT REMOVE TWO 7MM SCREWS ON BLACK PLASTIC STRIP THAT YOU SEE AFTER REMOVING STEERING PANEL....PRY THIS STRIP OF PLASTIC OUT JUST A LITTLE AND CUT IN THE MIDDLE .
NEXT REMOVE TWO 7MM SCREWS FROM AROUND TOP OF INSTRUMENT PANEL (BY GAUGES ) PRY PANEL STARTING FROM AROUND VENT ON LEFT BY DRIVERS DOOR ""THIS PANEL WILL STAY IN PLACE LOOSE... NO NEED TO REMOVE!""
NEXT YOU WILL SEE 0NE 7MM SCREW BY GEAR SELECTOR AREA.. BEHIND THE LOOSE PANEL REMOVE THIS SCREW.. ALSO IN SAME AREA BUT LOWER THERE IS ONE 7MM SCREW THAT NEEDS TO BE REMOVED THAT HOLDS LOWER DASH PAD ITS FOUND BEHIND LOWER CORNER OF DASH PAD.( LOWER DASH PAD GAS PEDAL AREA )
"DON'T"!!! REMOVE THE FOUR 10MM BOLTS!!!! IN SAME AREA
NEXT REMOVE RADIO /AC CONTROL TRIM WITH THIN SCREW DRIVER OR PANEL TOOL IT HELD IN BY SIX CLIPS...NO NEED TO DISCONNET ANYTHING IT WILL STAY THERE HANGING!!
NEXT REMOVE TWO CENTER CONSOLE LOWER LARGE PLASTIC CLIPS BY FLOOR MATS. NEXT UNDER SQUARE BLACK RUBBER AT CENTER CONSOLE REMOVE ONE SILVER SCREW. MOVE SEATS FOWARD AND REMOVE TWO 8MM SCREWS FROM SIDES OF CENTER CONSOLE FROM BACK SEAT.
PRY CUP PANEL SECTION THAT WAS HELD DOWN BY SILVER SCREW ...PRY UP TOP HALF OF CONSOLE STARTING FROM SECTION WHERE ARMREST DOOR IS.. DISCONNECT LIGHTER PLUG AND REMOVE PANEL .
NOW YOU WILL SEE SIX SCREWS STARTING FROM BELOW RADIO TRIM WORKING BACK TO ARMREST DOOR

Dec 04, 2010 | 2004 Ford Explorer

2 Answers

I need to remove driver side seat on 2009 Maxima my wife dropped a diamond from her ring and need to get access to get it out from under the seat


should be 4 bolts holding seat into floor pan, one under each corner of the seat. Remove bolts, unplug any power connections , seat should come right out.

Aug 01, 2010 | 2008 Nissan Maxima

1 Answer

Center console disasembly instructions . we are trying to remove the center console


Base Console, Floor, Ranger, Explorer Removal and Installation
  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest (644A22) from the floor console.
  1. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  1. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  1. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  1. Lift the floor console from the front and rear console panel mounting brackets.

c758709.gif

Apr 01, 2010 | 1996 Ford Explorer

1 Answer

Between seat console in 1999 Chevy Prizm


nope not without removing center console it there metal items u could try magnet but center console really not that hard to remove to remove center console look to see if any screws on top part if not more than likely just clips holding it on pry up gently if it just clips should come up farily easy if u have to put alot of force against it your missing screws or something look closer if u can get top cover off u should be able to get at items

Feb 13, 2010 | 1999 Chevrolet Prizm

1 Answer

Dropped jewelry (ring) down between driver seat and consol.


yes it should she be 4 bolts, two in front and two in back. If its electric just be careful to not rip any wires

Jun 10, 2009 | 2009 Porsche Cayenne

1 Answer

Removal of center tray on Saturn Relay


Remove the seat. Should be some torx head bolt attaching it to the seat.

Dec 21, 2008 | 2005 Saturn Relay

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...