Question about 2007 Mercedes-Benz ML320 CDI

1 Answer

Wiring diagram for vss

We are looking signal for taxi meter

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Try American Taximeters & Communications Inc. 21-46 44th St. L.I.C. NY 11101. We just bought a 7800-0572 converter from them, it plugs into the OBDII plug under the dash, it was for a 2006 Ford 500. Good Luck. $150 plus shipping.

Posted on Aug 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the vss wire located on a 2006 prius


violet wire on 26 pin connector to the multi display

Oct 06, 2014 | 2006 Toyota Prius

1 Answer

Codes p0501 p0700 p1753 p1758p0706


vss dead (veh, speed sensor)
A/T 700 codes are transmission errors. so is p17xxx
706 is trans mission range switch open circuited (bad switch or wires)
the scan codes never tell you what part is bad or what to replace.
it tells you ONLY what tests fail. called Monitors.
a Service tech, does this magic,. with tools and meters and gauges and special tests.
you can look up codes here.
http://engine-codes.com/

you can go to alldata.com (or get a real honda fsm book)
in the book it covers each code and now to test it and find the truth.
for example they will show you how to find P0501.
by looking at the VSS signal if good, the wires are bad.
if the signal is bad, the sender is bad. using a scope or meter.
good luck to you.

Oct 26, 2013 | 1996 Honda Odyssey

1 Answer

I'm looking for a wiring diagram for an 1998 regal gs.


Test f66.53.gif A speed sensor. Courtesy of General Motors Corporation, Service Technology Group. A defective vehicle speed sensor may cause different problems depending on the computer output control functions. A defective vehicle speed sensor (VSS) may cause improper converter clutch lockup, improper cruise control operation, and inaccurate speedometer operation.
  • Prior to VSS diagnosis, the vehicle should be lifted on a hoist so the drive wheels are free to rotate.
  • Backprobe the vss output wire and connect the voltmeter leads from this wire to ground.
  • Select the 20-volt AC scale on the voltmeter.
  • Then start the engine.
  • Place the transaxle in drive and allow the drive wheels to rotate. If the VSS voltage signal is not 0.5 volt, or more, replace the sensor.
  • When the VSS provides the specified voltage signal, backprobe the VSS terminal at the PCM and repeat the voltage signal test with the drive wheels rotating.
  • If 0.5 volt is available at this terminal, the trouble may be in the PCM (powertrain control module).
  • When 0.5 volt is not available at this terminal, turn the ignition switch off and disconnect the wire from the VSS to the PCM.
  • Connect the ohmmeter leads across the wire. the meter should read zero ohm.
  • Repeat the test with the ohmmeter leads connected to the VSS ground terminal and the PCM ground terminal.
  • This wire should also have zero ohm resistance. If the resistance in these wires is more than specified, repair the wires.
  • The condition of a speed sensor can be checked by going through the diagnostic routines for the system.
  • If this test indicates that a sensor is faulty, the sensor should be replaced.
  • Speed sensors can also be checked with an ohmmeter. Most manufacturers list a resistance specification.
  • The resistance of the sensor is measured across the sensor's terminals.
  • The typical range for a good sensor is 800 to 1400 ohms of resistance.

btn-back_to_top.gif
0996b43f802438a6.jpg

Oct 20, 2012 | Buick Regal Cars & Trucks

1 Answer

1992 camaro, E-code (305tbi)- speedo inoperative,-gives code 24 no vss signal..-new vss installed, continuity good from vss to bulkhead connector and through to harness inside. there is supposed to be a...


Hi, I'm not familiar with the part, but the diagram shows it behind the glove box next to the ECM. Go in thru the bottom--remove the sound barrier, remove the EMC, then remove the buffer. What I recommend is to see if you can get one at a salvage yard. Otherwise, they are about $50 on eBay. Thanks for using FixYa.


jturcotte_1214.gifjturcotte_337.jpg

Mar 11, 2011 | 1992 Chevrolet Camaro

1 Answer

I need to install a centrodyne pulse divider in my 2007 dodge caravan to go with my centrodyne silent 610 taxi meter.


Call Lee at Centrodyne he will help you.
The pulse is most easily found on the transmission at the VSS output. It is a connector with two wires, you want the DG/V. Run that to the pulse divider green wire. From the meter, tie the white in the 2 stand cable to the pulse output. Hook up power and ground then calibrate the meter. You should end up in the 33,000 range for calibration.

Feb 05, 2011 | 2000 Dodge Caravan

1 Answer

I am looking for the speed signal output wire for a 2005 kia sedona.I am trying to hooh up a taxi meter.Can you help


Do not hook anything to a vehicles electrical system
You will load the circuit and have all kinds of issues.

The Speed Sensor is an output sensor that sends a signal to the
vehicles computer, for shift control stratagy. The output
will also be unusable for what you want to do.

Follow the taxi meters instructions

Jan 30, 2011 | 2004 Kia Sedona

1 Answer

I need to hook up a centrodyne taxi meter to 2000 dodge caravan. I need to know how to hook it up. thanks


It's very easy on the pcm you will find a blue/orange wire. That's you hook up wire(vss). There are two set of wires off the meter bracket one comes with three wires and the other one with two. The one with 3 one goes to battery(red) ground(black) and top light(green or white). The other set of wires only the white one is connected to the vss.(vehicle speed sensor)

Sep 29, 2010 | 2000 Dodge Caravan

1 Answer

99 Ford Escort ZX2 Speedometer/Odometer doesn't work


I'm sorry, I have to ask, this is an automatic right? That out of the way, Does the trans shift different when you drove it with the Vss unplugged when you had the ohm meter on it? 8.5 volts? Something sounds wrong here. I'll have to look up the wiring diagram before I can say thats a bad reading but it should be battery voltage (14 volts running) or 5 volts?

Jul 08, 2010 | 1999 Ford Escort

Not finding what you are looking for?
2007 Mercedes-Benz ML320 CDI Logo

701 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

yadayada
yadayada

Level 3 Expert

63242 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...