Question about Chevrolet Tahoe

1 Answer

Keeps triping braker - Tahoe Chevrolet Cars & Trucks

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 92 Answers


Posted on May 26, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Front ac warm back cool keeps triping low pres.sw.

Add freon. If it's a Chrysler, then there is a valve in the compressor low side. If it's present, remove it.

Sep 26, 2015 | AC Cars & Trucks

1 Answer

Cant find curcuit braker on my 97 saturn

It should be connected in series with a circuit. Since a circuit breaker acts as an "over current" switch it will be connected just an on/off would so as to "open" the circuit during an over current condition. This will remove power from the circuit.

Jul 15, 2012 | 1997 Saturn SL

2 Answers

My 01 sportage won't start. we put another motor, it winds over but there is no power going to coils.

I'm sure you forgot a connection, also make sure wire harnesses are all plugged and secure. possibly check for a fuel shut off switch, if the truck was jacked up or banged it could have triped the switch. is there fuel getting to motor?

Jan 14, 2011 | 2001 Kia Sportage

1 Answer

How to replace serpentine belt on a car

1. Make a drawing of the routing of the existing belt before you take it off, or there may be one on the fan shroud or nearby. 2. Locate the spring loaded tensioner. It will be a pully that is not connected to any other component. 3. You will need a long braker bar (most likely half inch drive). On the spring loaded tensioner you will find a place (a cut out square) to insert the braker bar. (Note, no socket is needed, just the braker bar itself) This is a secure way to leverage the tensioner 4. Using the braker bar, move the tensioner to release tension on belt. 5. Slide old belt off pulleys, and move around fan. 6. Install new belt with same method, making sure the routing is correct.

Oct 31, 2010 | 1997 Chrysler Sebring

2 Answers

Secuirty Light

Security system has been triped. Try using remote or key in the door. Lock door, then unlock. Should reset system. Let us know if that works.

Jul 29, 2009 | 1995 Jeep Grand Cherokee

1 Answer

How do i remove the nut to remove hub

use an impact or use a braker bar and get someone to hold the brake on for you or put a screw drive in the holes in the roter to keep it from turning .

Jul 12, 2009 | 1985 Chevrolet C2500

1 Answer

2003 ford escape, fuse keeps blowing for door locks, radio and dome light. y

check for a shorted to ground positive wire repair as nesseacry

Jun 01, 2009 | 2003 Ford Escape

1 Answer

Braker stay on after i hit them

brake light switch...easy fix

Apr 12, 2009 | 1998 Chevrolet Cavalier

1 Answer

2000 Blazer. No power to the orange wire for either front seat. Which fuse or relay controls the frt power seats? Its not listed on the fuse box covers and I do not have an owners manual.

The orange wire is the power wire for both seats.It gets its power from the power seat circuit braker (20 amp) located at the body relay block.It is located behind left side of dash near fuse block. Remove circuit braker and check for power in body relay cavity that you pulled the relay out of if power is on one side change circuit braker and if no power on either side then you have a bad main fuse near battery or under hood in main fuse block. Joe ASE Master Tech

Mar 05, 2009 | 2000 Chevrolet Blazer

1 Answer

Replacing the serpentine belt tensioner pulley

Johnson bar, crow bar, wrench, or 3/8 braker bar. GM's normally have a square hole where the 3/8s braker bar fits in and you can remove tensioin by using that. Some GM's there is a raised edge that's in a rectangle shape. Using a wrench, not sure the size, you can remove tension with that. You can use a crow bar but the braker bar is much more effective.

Aug 06, 2008 | 1994 Chevrolet Astro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides