Question about 2007 Kia Spectra5

1 Answer

I have a2005 kia specra and I CAN GET THE HUB OFF TRYED SPRAYING IT WITH release all. Used apuller with impact even try sum heat still would not come loose. and suggestions?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 308 Answers

Get a spray bottle and put a bottle of cheap break fluid in it spray the hub and connections with this try not to get it on any wires or paint. It will eat that paint off! It will also eat the rust off, also double check make sure that you have all the bolts out. If this is on the front you will have to compress the struts I believe, this could be what is holding you up. Assumed that you where working on the rear hubs. Good luck.

Posted on May 26, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My van keeps over heating . I've replaced thermostat, water pump and it's still over heat. The gauge tells me its hotter then it really is. Antifreeze. It's a2005 Chevy 3500 express van

have a compression test done
if the overheating is occurring at lights , high rpms with low road speeds or it stay right when travelling and it has a fan clutch ( viscous fan hub) replace the hub

Mar 13, 2017 | Cars & Trucks

2 Answers

What can I do to get door ajar light to go off on a2005 4 door vibe

The door ajar sensing switch is incorporated into the door lock assembly inside the door. Which door is causing the problem will be the question. In most cases it will be the drivers door as it is used most frequently. I have had some success spraying WD-40 into the lock assembly of the door and opening/closing it several times. This has worked on some makes and models. Others have needed switch replacements. Try the WD-40 spraying liberally on all lock assemblies and hope for the best

Jan 12, 2016 | Cars & Trucks

2 Answers

Hello my 2003 kia sorento will not start I tryed everything fuel pump cam and crankshaft I changed those parts I tryed starter spray and wants to stay on but once I stop spraying it cuts off help

Hi Papi:
Sounds like you have a fuel delivery problem for sure.
Is there a fuel filter that you can clean or replace?
Is this carb or fuel injection?
If carb, clean, flush, blow out with compressed air.
If F/I odds are the injectors are not being triggered.

Jul 03, 2015 | Kia Cars & Trucks

1 Answer

How to remove hub assembly 2003 kia sedona

If your talking about the rotor assembly, you have to remove the screws in the rotor. Use impact screwdriver to keep from stripping the screws.

Jul 04, 2014 | 2003 Kia Sedona

1 Answer

Kia grandsportage


Oct 05, 2017 | Ford Cars & Trucks

1 Answer

How to remove front rotors

I used a hand impact wrench that I picked up at Sears for 24.99. The model number is 47641. Check this out under their website. Also used some PB blaster. Got one side off but I need to try either a left handed drill bit. If that doesn't work a screw extrator with some heat will hopefully do the trick. I am not going to try it until I can locate the screws from Kia.

Sep 24, 2010 | 2005 Kia Sorento

1 Answer

Kia rio ccvt 2007 ''' dry hot smell ventilation system.

sounds like you have a bad heater core leaking or seaping radiator fluid into the air ducts

Jan 06, 2010 | 2007 Kia Rio 5 Sx M/T Hatchback

2 Answers

1991 geo strom front wheel bearing can not get the hub a part.

you may need to heat the hub up with a small hand torch, the heat may have fused it together a bit, and try tapping on it with a small mallet

Jul 04, 2009 | 1993 Geo Metro

1 Answer

Can't get the bearing hub out to replace the bearing

You'll need to remove the 2 strut bolts holding the hub to the strut, remove the axle nut. Pull the hub towards you and try taping on the axleshaft to try to push it out. You might try spraying some WD-40 where the axleshaft goes thru the hub.

May 24, 2009 | 2006 Kia Sorento

Not finding what you are looking for?
2007 Kia Spectra5 Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

79865 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides