Question about 1999 Pontiac Grand Am GT

1 Answer

1999 grand am gt 3.4 head torque - 1999 Pontiac Grand Am GT

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 23 Answers

Requires new head bolts. also requires thread sealant to be applied to bolts because they go into coolant passages. The torque spec is 60 n.m (44 lb ft) and then and additional 95 degrees. It suggests using a torque angle meter however its just slightly more than one-quarter turn the sequence is as follows. 5 3 2 8
7 1 4 6

Posted on May 25, 2011

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 161 Answers

SOURCE: TORQUED HEAD BOLTS TO 60LBS

inch pounds for startersget manual procedure is 6 6 step two step tighten lossen tighten long an short then loose n one at a time an retorque..need proceedure in front of you dealer or part store may copy or print off for you...

Posted on Mar 20, 2011

csmock132
  • 4669 Answers

SOURCE: need the head bolt torque specs for a 1999 grand

There is a service bulletin on this. They have changed the spec, The new spec is 44ft lbs. Then an additional 95 degrees. Start from the center and work you way out

Posted on Mar 30, 2010

  • 512 Answers

SOURCE: Head Bolt Torque for a 2000 Grand Cherokee Laredo 4.0L

the torque is a 4 step process

1 torque all bolts to 22 ft/lbs
2 torque all bolts to 45 ft/lbs
3 recheck all bolts to 45 ft/lbs
4 torque bolts 1 thru 10 to 110 ft/lbs
bolt 11 to 100 ft/lbs
bolts 12 thru 14 to 110 ft/lbs
bolt #1 is the fourth bolt from the front on the passenger side....#2 is the fourth bolt on the drivers side then you continue in a clockwise order

Posted on Jan 04, 2009

johnny5846
  • 379 Answers

SOURCE: what are the torque specs for the head bolts for a 1999 sportage

hi bob
head torque on the 2.0 DOHC is 64 ft lbs , done in two -three steps , also there is a sequence for proper order . here is a very good description with graphics .

1999 kia sportage 2.0 DOHC head torque

Thanks for using FIX YA !

J5

Posted on Jan 24, 2009

drsinister69
  • 2317 Answers

SOURCE: 1999 grand prix gt 3.8v 6 error codes 300 and 302

The PO300 code is random/multiple cylinder misfire detected. Sinsc you have the code PO302, that means that cylinder 2 is the one misfiring, usually a bad coil pack, or spark plug.

Posted on May 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cylinderhead torque settings


I'm not sure what engine you have in your 95 grand am SO I will give you both the 4cyl and 6cyl Specs. Also you didn't ask for the torque sequence. I will include that as well for both. 2.3 DOHC Quad 4cyl: Torque sequence---> front ' 7 3 1 5 9 ' of engine ' 8 6 2 4 10 ' Step 1: torque bolts 1 thru 6 (26 Ft/Lbs & 90 degree turn) Step 2: torque bolts 7 & 8 (15 Ft/Lbs & 90 degree turn) Step 3: torque bolts 9 & 10 (22 Ft/Lbs & 90 degree turn) Recheck final torque in sequence *** CAUTION *** This engine uses "Torque To Yield" (TTY) head bolts that means they permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed in order to obtain proper torque. 3.1 liter V6 Torque sequence--> ' 6 2 3 7 ' ' 5 1 4 8 ' Step 1: torque bolts in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION *** This particular engine uses "Torque To Yield" head bolts(TTY) (that means the bolts permanently stretch during the initial installation.) You MUST use NEW head bolts when replacing or reinstalling the cylinder head in order to obtain the proper torque.

Aug 22, 2014 | 1995 Pontiac Grand Am

1 Answer

Need torque spec's for 1999 Grand Am 2.4L motor valve pan gaskets bolts? thanks


I need know the torque head Pontiac Grand am se 1999. Machine 2.4

Mar 24, 2012 | 1999 Pontiac Grand Am GT

2 Answers

I need lower manifold rocker and upper manifold torque instructions please help


Head Bolts
Torque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation.New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.
The Intake Bolt Torque 10 Foot pounds (Final torque)
Note:to torque bolts & nuts, start in center using crisscross pattern working outward

Dec 05, 2010 | 2000 Pontiac Grand Am GT

1 Answer

4.3 v6 head gasket torque schematic


first round is at 22lbs, second 44lbs, third 66lbs. make sure you get the order in which the bolts need to be tightened as not to warp the cylinder head, and that sequence is in the package your new head gasket (s) came in. If you cant find it, your local garage will photocopy it for you.

Aug 01, 2010 | 1999 Pontiac Grand Am GT

4 Answers

Need the head bolt torque specs for a 1999 grand am - i am trying to replace the heads on 1999 grand am with 3.4 engine


Fig. Cylinder head bolt tightening sequence-3.1L engines & 2001-04 3.4L engines

7245611.jpg


Fig. Cylinder head bolt tightening sequence-2005 3.4L engines

5579e52.jpg

Hope this help (remember rated and comment this).

Mar 30, 2010 | 1999 Pontiac Grand Am GT

2 Answers

What is the tension on cylinder head bolts for a jeep grand cherokee 307935 4 litre, 6 cylinder, 1999, petrol motor.


Coat threads of left hand front bolt with sealant: 1st - step; - 22 ft./lbs. 2nd - step; - 45 ft./lbs. 3rd - step, all bolts except L.H. front bolt; - 110 ft./lbs. 4th - step, L.H. front bolt; - 100 ft./lbs. fig100.png

Sep 05, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Serp belt squeaks....do I need a torque wrench to replace it


No torque wrench needed to change the belt. You will need a 3/8 rachet with a narrow head works fine. You will see on the front of your engine on the lowwer left side(if your standing at pass. fender) the tensioner it will have a slot for your rachet.

Apr 10, 2009 | 1999 Pontiac Grand Am GT

1 Answer

I'm trying to find out what the torque is on the cylinder heads for a 3.4 pontiac grand am 99


1st u must use all new head bolts, that said follow this factory procedure from the manual.
HEAD BOLT TORQUE FOOT POUNDS (FINAL TORQUE) TORQUE SEQUENCE --------- | 6 2 3 7 | | 5 1 4 8 | --------- STEP 1: TORQUE IN SEQUENCE TO 33 FT/LBS STEP 2: TURN AN ADDITIONAL 90 DEGREES RECHECK FINAL TORQUE IN SEQUENCE *** CAUTION *** ENGINE USES TORQUE TO YIELD HEAD BOLTS (TTY) THAT PERMANENTLY STRETCH DURING THE INITIAL INSTALLATION. NEW HEAD BOLTS MUST BE USED WHEN CYLINDER HEAD IS REPLACED OR RE-INSTALLED TO OBTAIN PROPER TORQUE. ALWAYS COAT BOLT THREADS WITH THE PROPER SEALANT

Feb 20, 2009 | 1999 Pontiac Grand Am GT

Not finding what you are looking for?
1999 Pontiac Grand Am GT Logo

556 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...