Question about 2002 Chrysler Sebring

1 Answer

I have a 2002 chrysler sebring convertible that is leaking coolant from a plastic thing that has 3 hoses--one coming off the overflow and one off the radiator and the 3rd going to the back of the motor. the leak is around the top of the plastic thing. is this the thermostat housing or something else and where can i get a replacement?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 23 Answers

Advance auto parts sells this. should be a dorman part number 902-302. Its called engine coolant outlet flange

Posted on May 25, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 Chrysler sebring has oil in coolant overflow reservoir. Why, how could the oil be getting in the reservoir?


it maybe the transmission cooler lines inside the radiator that have leaked into the coolant. the only way to fix is to replace the radiator.

Sep 09, 2014 | 2009 Chrysler Sebring

1 Answer

I have a 2002 sebring, 2.7 liter engine, dash always reads normal, but when you drive the car and then turn it off the overflow boils and pops reservoir hose off and shoots hot coolant, just replaced the...


Why would you drive the car other than to get home the
first time all that happened?
Have you not had the issue diagnosed at a repair shop?
Sounds like a head gasket or coolant flow issue

Aug 08, 2013 | 2002 Chrysler Sebring

1 Answer

Coolant Resevoir Tank Leak


A repair might buy a little time but you should replace.Either the junk yard or dealer will have this part.it is a coolant resevoir.

Aug 28, 2012 | 2002 Chrysler Sebring

1 Answer

1993 jeep grand cherokee havc code 06


Chrysler & Jeep Cooling System & HVAC Service: Every car make has its quirks, and Chrysler and Jeep vehicles are no exception. In researching this article, we found several examples of heater problems in these vehicles that seem to be fairly common.

On 2001 and 2002 Sebring Sedan, Sebring Convertible and Stratus Sedan, plus 1993 to 2002 Chrysler Concorde, LHS, New Yorker and 300M, Eagle Vision and Dodge Intrepid models with V6 engines, customers may complain their engine is overheating, or the heater is putting out little or no heat.

Chrysler Technical Service Bulletin 07-002-02 says the problem can be caused by a low coolant level in the cooling system. On these vehicles, air trapped inside the cooling system can displace coolant when the system is refilled. The radiator and coolant reservoir may appear to be full, but there still may be air inside the heater core and heater hoses. This will create a low coolant level that may lead to overheating and low heater output. The bulletin provides a special fill procedure to eliminate the trapped air so the cooling system can be completely filled.

The procedure goes as follows:
1. Obtain Chrysler special tool 8195 (Cooling System Filling Aid). The tool looks like a funnel and attaches onto the filler neck (just as a regular pressure cap does). But it also has a hose clip.
2. Attach the filling aid tool to the cooling system filler neck. Use the clip to pinch off the overflow hose attached to the fill neck. Attach a 4-6' long 1/4" ID clear hose to the bleed valve. Put the end of the hose into a clean container (to prevent coolant from spilling onto the accessory drive belts).
3. Open the cooling system air bleed valve before any coolant is added. If you do not do this, air can remain trapped inside the system and you won't get all the air out. On 1998 and later models with 2.7L engine, the valve is located on the water outlet connector at the front of the engine. On 3.2L and 3.5L engines, the valve is located on the lower intake manifold, left of center under the upper intake manifold. On 1993-'97 models with 3.3L and 3.5L engines, the valve is on the thermostat housing.
4. Pour a 50/50 mixture of coolant and water into the large side of the filling aid funnel. Use distilled, deionized or reverse-osmosis purified water, not ordinary tap water, which may contain salt or minerals that could contaminate the coolant.
5. Slowly fill the cooling system through the large side of the filling aid. Watch the hose connected to the bleed valve. When a steady stream of coolant comes out of the hose, close the bleed valve and continue filling to the top of the filling aid.
6. On 1993-'97 models, place a small, clean container below the end of the overflow hose. Then remove the clip from the overflow hose. Any excess coolant in the filling aid will now drain into the overflow section of the coolant bottle or into the container.
7. On 1993-'97 models, remove the reservoir and recycle the excess coolant.
8. Remove the filling aid from the fill neck. Make sure the filler neck and cap are clean, then replace the pressure cap on the coolant bottle.

Note: 1998 and later coolant bottles have two chambers. Coolant will normally only be in the inboard (smaller) of the two. The outboard chamber is only to recover coolant in the event of an overheat and should normally be empty - except for the coolant drained from the filling aid. This coolant will be drawn back into the pressurized side of the cooling system over time.

Hope helps.

Jan 12, 2011 | 1993 Jeep Grand Cherokee

1 Answer

Where is the thermostat located in the 2002 Chrysler Sebring convertable. I have a leak coming from something and My thermostat light went on along with the gage going to hot


Follow the upper rad hose from the radiator and it will take you to the thermostat housing,the thermostat is in that housing.

Sep 29, 2010 | 2002 Chrysler Sebring

1 Answer

My 2001 chrysler sebring convertible .. the heat blows cold after 5 minutes of driving


check the coolant level in the radiator when the engine is cold,fill it to the top,and also check the coolant level in the overflow container and fill it to the full line on its side

Jan 21, 2010 | 2001 Chrysler Sebring

2 Answers

Sebring 2003 2.4l Coolant reservoir emptied


Fill the coolant system back-up to level and pressure test the system. Check for chalky, white trails, antifreeze trails, spots on the ground, and see that the pressure is holding for more then five minutes. Could be: head-gasket, freeze plug, hose, heater core, water-pump, or radiator.

Jun 11, 2009 | 2002 Chrysler Sebring

2 Answers

2002 Chrysler Sebring convertable 2.7L engine coolent leak


Replace the water outlet housing. Most likely not covered, but doesn't hurt to ask.

Mar 05, 2009 | 2002 Chrysler Sebring

Not finding what you are looking for?
2002 Chrysler Sebring Logo

809 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...