Question about 2002 Jaguar X-Type

Open Question

I have an xtype 2.5 sport which is showing powertrain malfunction.initial error code is p1643..can network tcm ecm but on another diagnostic machine it also showed p 1582..wiring inertia switch activated/defective, the car is in limp home mode. there,s no sign of water ingress,chaffed wires or blown fuses and the car starts first time with no uneven running . also, the g/box changed gear perfectly b/fore lights came on.car had been parked up for 2wks. prior to fault

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: need to clear fault codes on jaguar x-type 2.5

disconnect the battery for 10 minutes.

Posted on Jul 27, 2008

  • 1 Answer

SOURCE: x-type jaguar automatic (gear box fault)

I have a 2002 X type (2 litre. done 44000 miles), dash showed gear box problem, (red circle light up). I pulled out and turned the engine off. 5 minutes later turned the engine on. The engine running but the car would not drive either in drive or reverse. Turned the engine off again and on the car driving but not much power. The care is taken to the Jag. dealer and told is misfiring + some gear box faults. Suggesting to change some coils and see (cost about £200+). also possible need to change the gear box costing about £2500+. Please advice. Shall I go ahead with the repair? Should I part exchange.

Posted on Aug 10, 2009

  • 1 Answer

SOURCE: Gearbox fault of Jaguar S Type

hi,change the gear box solonied c.should b ok than ali g autos birmingham 07971335303

Posted on Oct 04, 2009

duane_wong
  • 6826 Answers

SOURCE: Powertrain warning light & engine light have

The powertrain and engine lights indicate that maybe codes have been stored in the computer.
Maybe have it scanned with an OBD-II Scanner at Autozone or Advance Auto Parts if they support Jaguar. I'm not sure about that.

At any rate, have someone with the proper scanner, possibly a Jaguar tech scan the engine codes for you and maybe analyze it.

My online resource didn't publish information on fault codes specifically for the Jaguar X-Type.

Good luck on this diagnosis and repair.

Posted on Nov 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Shift light flashing no OD Changed Trans ecm/pcm shift hold light button, coil No change. CYL missfire, 2 & 3 Diagnostics code on Trans is u0401 Invalid data received from ecm/pcm/a


Circuit Description
Modules that are connected to the shared communication circuits monitor for serial data communications during normal vehicle operation. Operating information and commands are exchanged among the modules. The modules have pre-recorded information about what messages are needed to be exchanged on the serial data circuits for each virtual network. The messages are usually supervised and some periodic messages are used by the receiver module as an availability indication of the transmitter module.

DTC U0401 TCM received invalid data from ECM
Conditions for Setting the DTC
The transmission control module (TCM) detects an invalid throttle position signal, engine speed signal and/or engine coolant temperature signal for more than 2 seconds.

Action Taken When the DTC Sets
• The TCM will store the DTC when a failure is detected on the first ignition cycle.
• The TCM will illuminate the HOLD lamp.
• The TCM can no longer determine the validity of any information it may or may not receive from the engine control module (ECM). Therefore the TCM substitutes default values for engine speed, throttle position, and other engine data signals.
• Transmission operation will be reduced, affecting shift points, torque converter clutch operation, and other driveability concerns.

Diagnostic Aids
• An intermittent malfunction may be caused by a fault in the electrical circuit. Inspect the wiring harness and the components for an intermittent condition. Refer to Intermittent Conditions in Engine Controls 1.6L.
• Repair any electrical circuit faults that were found. Refer to Wiring Repairs in Wiring Systems.
• Faulty ECM and/or TCM

Install a scan tool.
Turn ON the ignition, with the engine OFF.
Save the DTC and Freeze Frame information into the scan tool memory.
Perform the scan tool Clear DTC Information function for the transmission control module (TCM) and the engine control module (ECM).
Operate the vehicle for 1 minute or until the MIL illuminates.
Check the TCM for DTCs.
Is the Malfunction Indicator Lamp (MIL) On?
--
YES - Go to Step 2
NO - Repair the wiring connectors for intermittent failure

Select request DTC status from the Diagnostic Trouble Codes Information menu
Request DTC by status
Is DTC U0401 displayed?
--
YES - Go to Step 3
NO - Repair the wiring connectors for intermittent failure
3
Turn OFF the ignition.
Disconnect connector A from the TCM.
Turn the ignition ON, with the engine OFF.
Measure the resistance between terminal A17 of the TCM wiring connector and terminal K14 of the ECM wiring connector.
Measure the resistance between terminal A7 of the TCM wiring connector and terminal K15 of the ECM wiring connector.
Was the resistance the specified value for both circuits?
0 ohms
YES - Go to Step 5
NO - Go to Step 4

Mar 19, 2016 | 2005 Chevrolet Aveo

1 Answer

P0740


Error Code: P0740
Description:
Torque Converter Clutch (TCC) Solenoid - Circuit Malfunction
Possible Cause:
Wiring.
Torque converter clutch (TCC) solenoid.
Engine control module (ECM)/Powertrain control module (PCM)/Transmission control module (TCM).

Mar 24, 2014 | 2003 Acura 3.2TL

1 Answer

Nissan altima p0725


HERE IS THE ANSWER.
P0725 - Nissan Type Powertrain - Transmission - ISO/SAE Controlled Description Engine speed (RPM) - incorrect voltage signal ECM to TCM
Cause Wiring, RPM sensor, TCM, ECM
P0720 - Nissan Type Powertrain - Transmission - ISO/SAE Controlled Description AT - vehicle speed sensor (VSS)
Cause Wiring, VSS, TCM
P0710 - Nissan Type Powertrain - Transmission - ISO/SAE Controlled Description Transmission fluid temperature sensor - excessively high or low voltage
Cause Wiring, temperature sensor, TCM, ECM
P0826 - Generic Type Powertrain - Transmission - ISO/SAE Controlled Description Up and Down Shift Switch Circuit

the dtcs of your car are so many, my best suggest is go to garage for repair. or if you would like to repair by yourself, you need to buy a diagnostic tool such as multidiag j2534

Jul 07, 2013 | Cars & Trucks

1 Answer

Bad transmition, the car wonte will not go in drive or reverse, just revs up real high


code p0743 refers to torque converter clutch solenoid-electrical=== causes wiring--clutch solenoid ECM/TCM
code p0750 refers to shift solenoid--A circuit malfunction=== causes wiring --- shift solenoid --ECM/TCM
code p0755 refers to shift solenoid B --circuit malfunction=== causes -- wiring---shift solenoid ---ECM/TCM
First is to check the wiring and connections are in good condition. next is to replace the clutch solenoid for the torque converter and work up from there

Jun 06, 2013 | Mazda 626 Cars & Trucks

1 Answer

I just got my car scanned and a few codes pop up


Error Code: P0130
Fault:
Oxygen Sensor (O2S) 1, Bank 1 - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) Triggered on first occurrence.
-Wiring harness.
-Oxygen sensor (O2S).
-Engine control module (ECM).

Error Code: P0505
Fault:
Idle Speed Control (ISC) System - Malfunction
Possible Cause:
-Wiring harness.
-Idle speed control (ISC) actuator/Idle air control valve (IAC) valve.
-Throttle motor.
-Throttle valve tight/sticking.
-Engine control module (ECM).

Error Code: P0100
Fault Location:
-Mass Air Flow (MAF) Sensor/Volume Air Flow (VAF) Sensor - Circuit --Malfunction
Possible Cause:
-Wiring harness.
-Mass air flow (MAF) sensor.
-Volume air flow (VAF) sensor.
-Engine control module (ECM).

Error Code: P1491
Fault:
Exhaust Gas Recirculation (EGR) Valve Insufficient Lift
Possible Cause:
-Wiring harness.
-EGR Valve.
-ECM

Error Code:P1607
Fault:
-Engine Control Module (ECM)/Powertrain Control Module (PCM)

Error Code: P0966
Location:
-Pressure Control (PC) Solenoid B - Circuit Low
Possible Cause:
-Wiring short to earth.
-Pressure control (PC) solenoid.
-Engine control module (ECM)/Powertrain control module -(PCM)/Transmission control module (TCM) .


Apr 30, 2013 | 2004 Honda Civic

2 Answers

Check engine light indicates p700 code


Diagnostic Test Code (DTC) P0700 is an informational code that is stored in the Engine Control Module (ECM) That informs the diagnostic technician that there are codes present in the Transmission Control Module (TCM) and that the TCM has requested the Malfunction Indicator Lamp (MIL) (AKA - Check Engine Light) to be turned on. This is because the MIL is controlled by the ECM and cannot be turned on directly by the TCM. So, the TCM requests the ECM to turn the light on. To find out the nature of the failure that caused the P0700, one must scan the TCM to retrieve the fault codes stored there. Please note that MOST generic OBD code readers cannot access the TCM - this is the reason for the P0700 code to set in the ECM (to alert somebody with a generic code reader that further diagnosis is needed for the TCM).

Feb 16, 2012 | 2000 Jeep Cherokee

1 Answer

Put trans in works great but has a code po 0700


P0700 is a generic fault code indicating a transmission problem. It's possible it's a left over code from the bad transmission you replaced. You may need to have the code cleared at a transmission shop that uses a different code reader to clear the code. Unfortunately, unlike the standard OBDII code reader, the transmission codes don't always reset themselves after a repair is made.

Oct 13, 2011 | 2000 Jeep Cherokee

1 Answer

S.govI just got a new engine in my 2001 sonata. it only has 20,000 mi. A new problem just surfaced- at 55 mph the car jerks and the check engine light comes on. The light goes off when I shut the car.


When a 'check engine light' (MIL=Malfunction Indicator Lamp) is turned on, there is a DTC (Diagnostic Trouble Code) set/stored in the ECM/PCM (Engine Control Module/Powertrain Control Module). This code identifies which engine management system component/function experienced a malfunction. Once you pull/read this code, you may begin diagnosis. I think you'll find P1529 (MIL On request from the TCM - Transmission Control Module.

Sep 13, 2011 | 2001 Hyundai Sonata

2 Answers

What is a kia rio p1800 error code mean?


the code is for engine torque signal malfunction.its either a short to voltage or ground in between engine computer and transmission computer. or a bad trans computer [tcm] manuel says check for shorts or bad connections at the connectors from ecm to tcm then states if no wire problems found then try a new tcm and if problem goes away then install new tcm.i know those instructions are lame but it comes from the kia service manuel. there are no tsb or recalls listed for that code. so i would recomend take to dealer because they would have a known good tcm to try.plus if you bought the car new then the 10 year 100,000 mile warranty may still be in effect beings how its a powertrain issue so if less than 100,000 miles and you bought it new it wouldnt hurt to ask them if it might be covered

May 29, 2010 | 2002 Kia Rio

Not finding what you are looking for?
2002 Jaguar X-Type Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...