Question about Mercedes-Benz G500
Not sure what model this is but if its a aluminium head on a cast iron block then 75lbs is about right ,yes i know the pundits will say tighten to whatever then 90? back and tighten 180 or something similar but how do they do it on the assembly line ,a massive air wrench with 12 sockets or whatever all at the same time ,I cannot see some little turkish car worker in dusseldorf messing about with this slacken and twist method when assembling 3 engines a minute ,if a diesel then 85/90
Posted on May 25, 2011
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Nov 29, 2015 | Cars & Trucks
Aug 04, 2014 | 2007 Mitsubishi Outlander 2.4
Mar 31, 2014 | 2003 Toyota Corolla
Mar 19, 2013 | 2005 Toyota Camry XLE
Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.
Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.
B2500 4 Cylinder
Torque sequence: --------- ' 10 6 2 4 8
' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51
Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final
tighten all bolts an additional 90 to 100 degrees recheck final
torque in sequence *** CAUTION ***engine uses Torque To Yield head
bolts (TTY) that permanently stretch during the initial installation.
New head bolts must be used when cylinder head is replaced or
re-installed to obtain proper torque.
B3000 3.0 6 Cylinder
Torque sequence ---------- ' 6 4 2 8 '
' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen
in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque
to 73 Ft/Lbs
B4000 4.0 6 Cylinder
Torque sequence --------- ' 5 1 3 7 ' '
' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in
sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs
Step 3: turn cylinder head bolts in sequence an additional 90-degrees
recheck final torque in sequence *** CAUTION ***engine uses Torque To
Yield head bolts (TTY) that permanently stretch during the initial
installation. New head bolts must be used when cylinder head is
replaced or re-installed to obtain proper torque.
Good luck with this job!
Feb 06, 2011 | 1998 Mazda Pickup
Fig. Cylinder head bolt torque sequence-3.8L engine
Fig. Tighten the cylinder head bolts using the following sequence-31L and 3.4L engines
Dec 16, 2010 | 2002 Pontiac Grand Prix
Nov 26, 2010 | 2004 Chevrolet Impala
Mar 06, 2010 | 2001 Chevrolet Venture
Nov 24, 2009 | 2001 Kia Sportage
Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme
61 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: