Question about Chevrolet Tahoe

1 Answer

2004 tahoe will not shift into 2wd. it operates fine in 4wd auto and 4wd. from doing some research and getting advice it seems to be the transfer case encoder motor and/or sensor?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Chevrolet Master
  • 1,026 Answers

Try reversing truck when you select 2 wheel drive ,this sometimes takes it out of four wheel
like a cone clutch .just need a little pressure off it .reversing takes pressure off hope this helps

Posted on May 25, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 ford ranger - Where is the 4x4 actuator located


On the transfer case
Transfer Case - Electronic Shift
The four-wheel drive electronic shift-on-the-fly feature electrically shifts the vehicle transfer case between 2WD, 4WD HIGH, and 4WD LOW. The system mode is selected by the operator through the mode select switch (MSS) on the instrument panel. The operator is informed which mode the system is in by two instrument cluster indicators: one for 4WD HIGH which appears as 4WD, and one for 4WD LOW, which appears as 4WD LOW. Shifts into 4WD HIGH can be made at any speed. When shifting into 4WD HIGH with the vehicle stationary, tooth blockage may occur preventing shift completion. When the vehicle is driven above 8 km/h (5 mph) the shift will complete. When shifting in or out of 4WD LOW, the four-wheel drive (4WD) control module requires that the vehicle speed be less than 5 km/h (3 mph), the brake pedal be applied, and the transmission be in NEUTRAL (automatic transmission) or the clutch pedal be depressed (manual transmission).
The gearmotor encoder assembly is mounted externally on the transfer case. It drives a rotary cam which moves the mode fork and range fork within the transfer case between the 4WD HIGH, 4WD LOW, and 2WD range positions.
The four-wheel drive (4WD) control module controls the gearmotor encoder assembly that shifts between 4WD HIGH, 4WD LOW, and 2WD modes.

Mar 17, 2017 | Ford Cars & Trucks

2 Answers

I have a 93 jeep Cherokee, it will move in 4wh and in 4wl but will not go back into 2wd?


Hello guy
try posting what 4wd system you have,? first.
command trac or select track, (the latter is full time)
part time or the full time system,
we cant guess it....
read the operators guide first, if a part time system only
as i suspect, stop driving on dry pavement.
it's only for ice, or dirt. part time. part time is not a full time system.
Command-Trac
shifting to 4wd on dry (means no ice) pavement causes, drive line wind up! and the gears to lockup. (see steering get tight in turns?> and is dangerous to drive it like this , you, me and the box)
posted here 100s of times.

http://www.rubicon-trail.com/4WD101/driveline-bind.html


the non grand Cherokee. early

had these choices
  • 1987-2001: New Process NP231 Command-Trac, part-time only, 2.72:1 ratio with low range
NP231 has the following settings: 2HI, 4HI, N, 4LO
  • 1987-2001: New Process NP242 Selec-Trac, full-time or part-time, 2.72:1 ratio with low range
NP242 has the following settings: 2HI, 4 full-time, 4 part-time, N, 4LO


as you can see you need to first know, what NP box you have or
photo your shift lever for 4wd, an post it and we tell you.

more facts, on select trac. (totally unlike command trac)
Selec-Trac locking hub is used on 4WD Cherokee. Selec-Trac
utilizes a non-disconnect front axle. Engagement of 2WD or 4WD is
accomplished at transfer case by means of mechanical shift linkage.
System allows full or part time 4WD. Selec-Trac can be shifted into
2WD or 4WD modes from inside the vehicle at any speed.
unquote
next from the service manual,
4WD TO 2WD
1) Place mode select switch in 2WD position. Transfer case
should shift to 2WD and not allow shifting into 4WD or LO range. Axle
should shift after transfer case shifts.
2) To determine if front axle has completed a shift out of
4WD into 2WD, position mode select switch back to 4WD position while
operating vehicle at slow speed. If vehicle shifts into 2WD, axle will
ratchet. If shift is not completed, transfer case will shift into 4WD
and hissing sound will come from mode select switch.
end quote.

if unsure read the FSM book its free.
shows you both systems and how to diagnose it.

in the box, click Cherokee,,then click 1993, and behold.
the real deal.

http://www.morris4x4center.com/knowledge-base/index.htm?utm_source=cj#service

4e7ebed4-9c81-4927-b26e-02808a82acff.jpg

May 10, 2016 | Jeep Cars & Trucks

1 Answer

2004 Tahoe stuck in auto 4wd and service 4wd light is on


switch on dash can cause this but the transfer case control module is the culprit most times.try disconnecting battery this will should reset the TCM.see what happens.worst case senereo is bad transfer case

Dec 10, 2013 | 2004 Chevrolet Tahoe

1 Answer

My 98 f150 was in 4WD Hi this morning when I started it. Selector switch is in 2WD position. 4WD Hi light is on, hubs (or front differential) is engaged and transfer case engage. (Feel front wheel hop...


If the switch was in the 2WD position and the transfer case was locked in a 4WD range, my 2 SWAGs would be bad switch or the connector to the shift motor is damaged / corroded or the fuse to the transfer case shift relay module is blown ( fuse # 17 ) / problem with the transfer case shift relay module.

This is without knowing if the truck was used in 4WD the night prior, and shifted out just before turning off. If this is the case, the shift motor might be stuck, and a few hits with a dead blow hammer to the transfer case might jar it free again ( do not use a metal hammer, it could damage the transfer case ).

The vacuum shift solenoids on the firewall are controlled by the GEM ( Generic Electronic Module ) which is grounding either the 2WD or 4WD solenoid, depending on the shift plate contacts in the transfer case. ( when in 4 or 4H, the contact switch plate signals the GEM, which in turn grounds the correct solenoid ).

Pulling the switch will not cause the transfer case to go back to a default position, the switch has a resistance level for each mode, and needs that value to operate the shift motor.

The resistance values for the switch between the 2 dark blue wires:
2WD - 4100 to 3700 ohms
4H - 1050 to 1150 ohms
4L - 380 to 340 ohms
- find the wire locations on the switch, mark them and remove the connector to test the resistance.

Just my opinion on the order :

1. Check the fuses for the shift motor
2. Try the old school shift method, back up ~ 50' put into park or neutral, and shift from 4WD to 2WD.
2.1. This is to see if the transfer case shift motor is bound up, and reversing might release it
3. Try hammering the transfer case with a dead blow hammer while someone shifts from 2WD to 4WD. You only need the key in the run position, if it happens quick enough after running the engine, the vacuum reservoir will still have enough vac to operate the solenoids. Don't chance running yourself over.
3.1. If this frees up the shift motor and the vacuum has bled off, you can try starting the truck and shifting into 4H then back to 2WD to get the front axle to disconnect or manually vacuum operate the front disconnect motor by applying vacuum to the pink vacuum line on the shift motor on the front axle.

Mar 05, 2011 | 1998 Ford F150 Regular Cab

1 Answer

1996 ford explorer 4wheel drive will not engage into the hubs need to know how it works


make sure your 4WD switch is working.and fuse is okay.because your 4WD is control by 4 electric shift motors in which drive a rotary cam which moves the mode fork and range fork inside the transfer case to select between 2WD HIGH A4WD - 4WD HIGH AND 4WD LOW RANGE.a shift motor sensing plate on the shift motor monitors the range in which the transfer case is operating a transmission range sensor monitors the gear position of the transmission.which must be in neutral to shift into low.a pair of solenoids one for 2WD one for 4WD.mounted on the upper right firewall route vacuum to the vacuum motor which engages and disengages the center axle disconnect collar in the front axle assembly.a 4 x 4 shift motor relay module contains two GEM controlled relays which shift the transfer case shift motor between 2WD and 4WD modes.a solid state clutch relay activates the A4WDclutch inside the transfer case.

Dec 13, 2009 | 1996 Ford Explorer

1 Answer

How do I shift into 4WD on my Suburban which is otherwise auto shift.


There should be a "stack" of buttons to the left of the sterring column on the instrument panel. They should be labeled something like 2H, 4H, 4L, and another for full time AWD. You need to push the desired button for the mode you are looking for. If you are in the full time mode the truck will operate in 2WD until it senses slipping and then will automatically distribute power to all 4 wheels. Some trucks, such as LS models, are not equipped with the full time mode so you'd need to push the 2H button to come out of 4WD.

I can't remember the exact insignia ont he buttons because my Tahoe is not here for me to look at. But you should notice the buttons right away. The GM's of that year did not use a lever to go to 4WD it was all push button.

Nov 14, 2009 | 2004 Chevrolet Suburban

2 Answers

2004 GMC Sierra 1500 4wd. Auto transfer case light issue


I have the same problem. It is intermittent and sometimes shows up with service transmission message. To get rid of it just put the truck in park, press the 2 high button and shift into drive while it is still flashing. I will worry about it more when it blows up. You can drive with the vehicle showing the solid neutral and it seems to make no difference. It has to be a wake up problem between the control modules. It only happens on start up.

Aug 27, 2009 | 2004 GMC Sierra 1500 Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...