Question about 1989 GMC Sierra

Open Question

Having trouble bleeding my master clutch cylinder

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Hydraulic clutch problems

i have a ktm 125 wich all ktms have hydraulic cluthcs and i have the same problem as all these fellas even when im riding it just sucks right down all the fluid reply to me on X-KTMrida-X@hotmail.com ok thanks fellas

Posted on Oct 27, 2008

Ad
autodr
  • 260 Answers

SOURCE: Bleeding clutch slave cylinder

i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Posted on Nov 15, 2008

fastboyz
  • 674 Answers

SOURCE: I installeda new clutch master

you need to back bleed the system.
snapon and parts stores sell a bleeder but for many year i have use just a simple pump oil can and a hose to connect to your bleeder fill your oil can with brake fluid and with the cover off you master. now just pump fluid up therw your master .

Posted on Jan 02, 2009

  • 2187 Answers

SOURCE: Bleeding Clutch Cylinder with no bleeder screw

I have not tried myself but see if the link below will work for your case. It is not the same model as you have but most vehicles have the same components for the non electronic parts. http://www.2carpros.com/forum/1988-dodge-dakota--bleding-air-out-of-clutch-master-cylinder-vt248517.html

Posted on Jun 04, 2009

  • 1 Answer

SOURCE: 1999 pontiac sunfire bleeding clutch

my 1999 pontiac sunfire drivers door latch is broke can not close the door. i have it pulled shut? how much will a used latch cost, or even 3 bolts for it? all the auto stores/ jumk yards are closed for me to call

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a clutch master cylinder on a 2006 toyota tacoma


remove line from the side of clutch master cylinder two bolts or nuts on firewall inside vehicle is a pin on the upper side of clutch remove and pull old unit out bench bleed new master by filling and pressing in on the piston of the master cylinder. if you dont have a hose fitting dont bench bleed bleed it in vehicle( this method takes longer) install back in vehicle and hook it all back up torque bolts to 25 ft lbs then bleed the slve cylinder from under vehicle near back of motor just like bleeding brakes pump up hold and release the line pressure by opening valve on slave cylinder.

Apr 06, 2013 | 2006 Toyota Tacoma

3 Answers

Why does clutch leak off and wont go into gear 96 toyota tacoma when you push on clutch pedal goes to the floor it wont engage clutch to be able to put into gear


the most likely reason is either the clutch master cyl. needs to be replaced.or the.slave cyl. its mounted down on the transmation under the hood find the resivore for the clutch. check the fluid level.if its low , fill it back up , and look for signs of a leak
you will probally have to bleed out all of the air from the system.its done almost the same way as bleeding the brakes. Good Luck.

Nov 05, 2011 | Cars & Trucks

1 Answer

I'm trying to bleed out the clutch on my 1998 Mazda 626. I am having trouble locating the area I need to press to bleed it. Is there a diagram on the website or somewhere showing where this is at? I know...


The bleed nipple will be located on the slave cylinder which is mounted on the side of the transmission. If you like , you can follow the hydraulic line down from the clutch master cylinder and it will go right to it. Also, if you fill the clutch master cylinder and simply pump the clutch pedal up and down with your hand, this system will eventually self-bleed and the pedal will firm up.

May 02, 2011 | 1998 Mazda 626

3 Answers

How do you bleed the clutch hydraulic system on a 2008 Mustang?


you bleed a hydraulic clutch the same way you bleed a brake system and it uses brake fluid as well.you keep bleeding until there is no more air in the clutch system.there should be a bleeder screw on the clutch slave cylinder that is were you bleed the clutch from.

Mar 18, 2011 | 2008 Ford Mustang

2 Answers

My 1996 Chevrolet K3500 Dually has a hydraulic clutch, how do I change the fluid and bleed it.


FIRST REMOVE ALL OLD FLUID FROM CLUTCH MASTER CYLINDER YOU CAN USE A SIPHON YOU HAND PUMP.AUTO PARTS STORES SELLS THE HAND PUMP SIPHONS. THEY DONT COST MUCH AND KEEP FROM MAKING A MESS.SIPHON OUT MUCH AS YOU CAN THE OLD FLUID IN THE CLUTCH MASTER CYLINDER.THEN POUR IN THE NEW FLUID DOT 3 BRAKE FLUID IN CLUTCH MASTER CYLINDER.OKAY YOU NEED A HELPER.LOCATE THE SLAVE CYLINDER.REMOVE SLAVE CYLINDER HOLD SLAVE CYLINDER 45 DEGREES WITH BLEEDER SCREW LOCATED AT THE HIGHEST POINT.HAVE A SMALL DRAIN PAN UNDER SLAVE CYLINDER.HAVE HELPER FULLY DEPRESS AND HOLD THE CLUTCH PEDAL THEN OPEN BLEED SCREW.CLOSE THE BLEED SCREW AND HAVE HELPER RELEASE THE CLUTCH PEDAL.REPEAT THIS PROCESS UNTIL ALL THE OLD BRAKE FLUID AND AIR BUBBLES LEAVES THE HYDRALIC SYSTEM AND WHEN YOU CAN SEE GOOD STREAM CLEAN FLUID NO BUBBLES YOU HAVE GOOD SOLID CLUTCH ALL IS GOOD.MAKE SURE THROUGH THE BLEEDING PROCESS YOU DONT LET CLUTCH MASTER CYLINDER RUN DRY OR YOU WILL HAVE TO START OVER.KEEP CLUTCH MASTER CYLINER FULL BRAKE FLUID WHILE DOING THE WHOLE BLEEDING AND FLUSHING PROCESS.

Jan 22, 2011 | 1996 Chevrolet C/K 3500

1 Answer

Are the brake master cylinder and the clutch slave cylinder interconnect in some way? I'm told that the slave cylinder get its fluid from the master cylinder.


The brake system and the clutch master cylinder have the same fluid tank, look at the brake master cylinder fluid tank, on the right hand side about half way up is a hose that goes over to the clutch master cylinder, if fluid level is not above this hose the clutch will stop functioning. If the clutch slave cylinder, mounted on the front side of transmission bellhousing, leaks then the clutch will stop functioning. The slave cylinder has a bleed screw, check these items and fill and bleed as neccessary. Hope this helps, let me know.

Jul 28, 2010 | 1995 Ford Escort

2 Answers

Bleeeding the clutch


This is what I would do.
Fill the master with brake fluid.
Make sure the slave cylinder bleeder is closed.
Have someone pump the clutch pedal fully down and while allowing it to come fully up about 20 times and then hold down.
Now with the clutch held down ........open the bleeder and hopefully some air will come out.
Repeat until fluid appears with out air.
The clutch master cylinder piston must be allowed to come fully back in it's cylinder to take in a new load of brake fluid with every pump and in normal operation.
Another way to bleed it......is to vacuum the fluid through the system from the master cylinder .......connecting to the slave cylinder bleeder valve.

Sep 18, 2009 | 1991 Chevrolet S-10

1 Answer

Clutch pedal stays 2 the floor on a hydralic clutch system on a 2000 camaro v8. clutch master cylinder is new also slave cylinder and clutch and pressure plate


Did you bleed the system? When you replace the the master and/or slave cylinder you have to bleed the system just as you would with brakes. There is a bleed screw on the slave cylinder. Open the bleed screw, have a helper depress and hold the clutch pedal down.Tighten the bleed screw, then release clutch. Repeat this procedure until you have removed all air from the system and the clutch pedal is firm. Keep an eye on the fluid level to avoid sucking air into the system. If you have done this, remember there is a possibility that the master or slave cylinder is defective.

Sep 06, 2009 | 2000 Chevrolet Camaro

5 Answers

Stuck clutch pedal on a Mazda B series truck


Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

2 Answers

Nissan Sentra won't move.


Most likly needs a new clutch. but before you do that make shore the clutch slave cylinder is releasing.Do this by opening the bleed screw on the clutch slave cylinder. If there is preasure released when you do his you may have a stuck master cylinder. Not likly but worth the trouble to try

Jun 29, 2009 | 2001 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...