Question about 1988 Ford Bronco II

1 Answer

Do i need a new fuel pump how to be sure before replacing

How to tell if i need a new fuel pump and which one it has two then how to install one

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 474 Answers

You are asking a lot without enough info

Posted on Aug 16, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to diagnose fuel injection problems on dodge 5.9


HII,
  1. Relieve the pressure in the fuel line before disconnecting it. To do so, you have to disable the electric fuel pump before you start the engine.To disable the fuel pump, do the following:
    1. With the engine off, remove the fuel pump fuse from the fuse box. (Your owner's manual should show you where it is.)
    2. Make sure that the parking brake is on and that the vehicle is in Park or Neutral, and then start the engine. It won't run very long after you start it up, but the pressure in the fuel lines will be reduced.
    3. Turn off the engine. With the fuel pump disabled, you're ready to disconnect the fuel lines from the filter.
  2. Look at the old filter and the new one before disconnecting anything.You should see an arrow stamped on both filters that shows in which direction the fuel flows through it. If the new one doesn't have an arrow on it, look to see in what direction the old filter is installed so that you can tell which end of the new filter goes where.
  3. Remove whatever is holding the old filter in place and remove it.
  4. Put the new filter on in the same position as the old filter.
  5. Replace whatever holds the filter in place, and make sure it's secure.
  6. Replace the fuse for the fuel pump in the fuse box. Make sure that the parking brake is on and that the vehicle is in Park or Neutral, and then start the engine and check for leaks around the filter.

Aug 24, 2015 | Dodge Cars & Trucks

2 Answers

Where's the fuel filter? When should it be changed?


its inside your fuel tank part of the fuel pump assembly

Aug 24, 2015 | 2010 Cadillac SRX

2 Answers

Changed the fuel filter but now car won't start?Please Help!!!


are you sure it was the fuel filter the actual problem? may be the fuel pump went out? check to see if you have fuel in the tank some mechanics put some fuel in the fuel filter just like they do with the oild filter.

Mar 23, 2014 | 1995 Mazda MX-6

2 Answers

Where is the fuel pump on 1996 mercury cougar xr7 with 4.6 v8


The fuelpump is located inside the gas tank, you will need to drop the tank and remove the pump from the top. also make sure to install new fuel filter.

Dec 08, 2012 | 1996 Mercury Cougar XR7

1 Answer

Installed new fuel pump because car had old gas in tank. removed tank and completly drained it. replaced tank and installed new fuel pump and fuel filter. put about 6 gallons of gas in car. have tried to...


Okay, you need to make sure the fuel pump is getting power and that you have the lines hooked up correctly. Also, when you replace fuel pumps you need to remove the air cleaner and use starter fluid to get the engine started.

Jul 09, 2011 | Nissan Z Cars & Trucks

1 Answer

How to install a new fuel pump on a 1985 Chevy,305 V8,


Remove the plunger rod by removing the plate that is bolted to the block. Clean all parts if needed.

Apply some axle grease to the plunger rod and reinstall into the block, replace plate, then carefully install fuel pump, making sure the plunger is under the push rod.

Just did this same thing on my '66 283.

Dec 17, 2009 | 1985 Chevrolet Caprice

3 Answers

Fuel pump problems


Some fuel pumps can be purchased and replaced by themselves. Other electric fuel pumps are combined with the fuel tank sending unit, and can only be replaced as a unit. ( as I believe your might be ). More expensiove this way, but thats how cars have become. Lucky you dont't have to buy the whole fuel tank, pump, and sender, as a unit. Hope this helps

May 08, 2009 | 2002 Chevrolet Blazer

2 Answers

99 dodge ram 3500 5.9 turbo diesel fuel problem


It is my understanding that the fuel lft pump has been replaced( updated) and is now gone back to the old way and is re installed in the tank.

I have had to put 3 lift pumps in since new, little did I know but Cummins tells me that the lift pump delivers minimal pressure and shortens the life of your injector pump.

So if that is true perhaps it is best to eliminate the lift pump and go with the new in tank pump. I plan on doing it the next time I have a problem.

Aug 27, 2008 | 1999 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...