Question about 2001 Jeep Cherokee

1 Answer

Cherokee 2.5crd. The wiring to an injector became disconnected. Engine stopped and wont start again. The fuel pressure to the injectors seems low. I have no access to diagnostic equipment.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 104 Answers

What it sounds like is see what happens is when that injector became disconnected the computer retarded the timing so the engine could keep up but seeing no fuel was supplied the motor..it turned off so no damage would be done ..thats what it sounds like... another possiblity is dirty injectors you can clean them for cheap with some white gas ..hope i could be of assitance

Posted on May 25, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 cutlass ciera 3.3injectors are not pulsing injectors ohm out 11.8-12 40lb of fuel pressure wiring to injectors are hot at a loss can the M.A.F.cause a no start it does start with starting fluid


MAF is probably not the problem - sounds like the engine is not getting the fuel it needs to start and either your injectors are fouled or the pressure regulator is stuck - that might cause the hot wires. The fuel pressure seems a bit low, but it should momentarily drop when trying to start the engine.

Mar 09, 2017 | 1990 Oldsmobile Cutlass Ciera

3 Answers

2000 Jeep Grand Cherokee Laredo 4.7 liter code reads p0307 turn the car off when I turn it back on started misfiring and sputtering and wont stay started now help


code p 0307 is misfiring on no 7 cylinder ====causes --- engine mechanical fault ---wiring---ignition/ fuel system--injector --ECT/MAF sensor---ECM
look for low fuel pressure or ignition control module

May 31, 2016 | 2000 Jeep Grand Cherokee Laredo

1 Answer

Car will turn over, and ocassionally sputter, but not fully start.


If this model has a Cam position sensor, try replacing it. Also having pressure at the test valve on the fuelrail does not mean the injectors are opening and delivering the fuel.

You may be able to borrow a test light for the injector harness through the Loaner programs at autoparts stores. Or use a Voltmeter to any one of the injector harness connectors by disconnecting an injector.

If you use Starting fluid and the engine does better at trying to run, then the injectors are not opening.

Sep 05, 2012 | 1995 Jeep Grand Cherokee

2 Answers

My 1998 dodge neon wont start until i pour gas in the throttle body then dies out when i press the gas


What is the fuel pressure when the engine is running ?
Has the filter been replaced ?

Aug 16, 2012 | 1998 Dodge Neon

1 Answer

Fuel injector. The car seems to drop a cylinder. I replaced the plugs and it ran well for about five minutes. It then started to miss again. I think number 3 injector is bad. How do I replace one injector.


FIRST YOU NEED TO RELIEVE FUEL SYSTEM PRESSURE BY REMOVING FUEL FILLER CAP THEN DISCONNECT FUEL PUMP HARNESS OR UNPLUG FUEL PUMP CIRCUIT RELAY, THEN START ENGINE LET IT IDLE UNTIL DIE LACK OF FUEL.TO REMOVE FUEL INJECTOR YOU NEED TO REMOVE FUEL DELIVERY PIPE WITH FUEL INJECTORS AS A ASSEMBLY TO REMOVE FUEL INJECTOR.YOU NEED TO TAG NUMBER ALL VACUUM HOSES AND PCV VALVE,NUMBER TAG FUEL INJECTORS WIRE CONNECTORS SO YOU CAN PUT EVERY THING BACK IN RIGHT PLACE.

Oct 14, 2011 | 1994 Toyota Corolla

1 Answer

Can you remove the injectors on 2003 Jeep Grand Cherokee diesell whithout removing the engine not a lot of space to get the back injector out ???????


YEP REMOVE TOP ENGINE COVER AND DISCONNECT INJECTORS ELECTRICAL CONNECTOR,REMOVE FUEL RETURN LINE FROM INJECTOR, REMOVE FUEL INJECTOR HIGH PRESSURE LINE, REMOVE FUEL INJECTOR RETAINER AND RETAINING BOLT,THEN REMOVE FUEL INJECTOR FROM THE CYLINDER HEAD. YOU NEED A FUEL INJECTOR EXTRACTOR TOOL 9075A ON TO INJECTOR AND CYLINDER HEAD.YOU DONT HAVE TO REMOVE THE ENGINE.

Jun 29, 2011 | 2003 Jeep Grand Cherokee

1 Answer

Where is the fuel filter for 4.0 v6 cherokee located


  • Disconnect the negative battery cable and then remove the fuel tank cap to release fuel tank pressure. Remove the fuel pump relay from the PDC. Start the engine and allow it to run until it stops. Select any injector and unplug its connector.

  • 2

    Connect a jumper wire from an injector terminal to the positive battery terminal. Then, connect the other jumper wire to the other battery terminal. Briefly touch the end to the negative battery terminal.

  • 3

    Locate the fuel filter/pressure regulator near the front of the fuel tank, mounted to the body above the rear axle. Disconnect the fuel supply, fuel return and fuel pressure lines. Remove the mounting bolts and then the fuel filter/pressure regulator.

  • 4

    Attach the new fuel filter/pressure regulator to the body and tighten the bolts to 30 in-lbs. Reconnect the fuel supply, fuel return and fuel pressure lines. Reconnect the negative battery cable. Start the engine of your Jeep and check for leaks


  • good luck hope this helps

    Dec 04, 2010 | 2003 Jeep Grand Cherokee

    2 Answers

    Help w 1994 chevrolet truck


    This injector set-up needs a specific fuel pressure supplied to the fuel rail to even start, much less run properly. The fuel pump is immersed in fuel inside the gas tank to keep it cool and not burn up. Running the fuel level low causes more heat in the pump and interuptions in proper fuel pressure. AC/Delco pumps have proven to be a reliable fix, the aftermarket pumps only last for a month or two sometimes. Check fuel pressure under the hood and power and ground to fuel pump at electrical harness at top of gas tank. This truck needs a fuel pump.

    Aug 18, 2008 | 1994 Chevrolet C1500

    1 Answer

    4.0 litre engine, auto transmission, long cranking time before it starts. When it starts there is a smell of gsoline, rich.


    CHECK INJECTOR LEAK DOWN. INSTALL FUEL PRESSURE GAUGE, PRESSURIZE FUEL SYSTEM BY LETTING ENGINE RUN FOR A MINUTE, SHUT ENGINE DOWN, AND OBSERVE FUEL PRESSURE. IT SHOULD NOT DROP BY MORE THAN 15-20 PSI IN A HALF HOUR. IF IT DOES PRESSURIZE FUEL RAIL AGAIN AND REMOVE FUEL RAIL WITH INJECTORS STILL ATTACHED AND LOOK FOR FUEL DRIPPING OUT OF INJECTORS. IF FUEL IS DRIPPING REPLACE INJECTORS AND SEALS.

    Aug 12, 2008 | 1996 Jeep Cherokee Sport

    Not finding what you are looking for?
    2001 Jeep Cherokee Logo

    Related Topics:

    116 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jeep Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Kevin Daniels

    Level 3 Expert

    1455 Answers

    Are you a Jeep Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...