Question about 2007 Dodge Ram 3500 Quad Cab Laramie

Open Question

No bus The odometer in my 2001 3500 diesel says no bus and none of my gauges are working. The fuel gauge will come on for just a second every once in a while but only for a second. Auto Zone ran the codes and got two responses i dont understand. the first was P1698, definition was no CCD message from TCM. The second was P1689, definition was no comm between ECM and IPM. Please help i need an explaination i can understand. I have mechaniced for years but have never done any computer work or electronic work.

Posted by on

  • Anonymous Dec 23, 2008

    my 2001 dodge 2500 spit and sputtered then died and if i leave the key on where the odometer is it says no bus , and there is no flame (loss of ignition)

×

3 Suggested Answers

  • 87 Answers

SOURCE: BBECM fault-no CCD from TCM

Your trans control module is more than likley the problem due to the fail tcm

Posted on Mar 28, 2009

cansmo
  • 2429 Answers

SOURCE: i have code p1698 says it might be na ccd message

Transmission control module failure. very common failure. On the transaxle right on the front when you open your hood . That module has been updated. That is the one that failed. before you replace it look along the wire leading from it is it disconnected did battery corrosion from the terminal corrode it, .That is where communication to the transmission control takes place

Posted on Apr 22, 2011

dttech
  • 4803 Answers

SOURCE: codesFEILED ECM-TCM

There are a couple of possibilities here. That type of code can set due to low battery voltage at one or more of your computer modules. The integrity and codition of the battery and charging system should be verifeid FIRST. If you have had to jump-start your vehicle (for whatever reason) this could be the cause of this code. If this is the reason for it, all that needs to be done is to repair whatever caused the low battery condition and clear the code.

Otherwise, there is a problem in the data circuits between the modules in your vehicle. If there has not been a low or shorted battery condition, then there is most likely an open circuit in your CCD BUS (network circuit wires) You will have to diagnose the problem with a scan tool that has the capabilities to access the ENTIRE computer network in your vehicle to determine where the problem is actually located. Possible causes are broken wires, or loose or corroded connectors, or a failed computer module. Please note that computer module failures are relatively RARE. I do not recommend replacing ANY computer module without FIRST performing proper diagnostics to PROVE that a loss of communication is the fault of the module itself and not the circuits leading to it.

Posted on Nov 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Every thing works no gauges working


None of my gauges will work, but my turn signal indicators ...

www.americanautowire.com/.../none-of-my-gauges-will-work-but-my-tu...
None of my gauges will work, but my turn signal indicators, high beam ... As we've discussed previously, anything electrical needs a 12 volt feed and ground to work. ... 09/28/2015 There are a number of new products coming in Nov/Dec this ...

my gauges quit working - CarGurus

www.cargurus.com > Questions > Ford > F-250 Super Duty

CarGurusSep 21, 2013 - my gauges quit working - My odometer, speedometer, fuel, tach, trip, and ... I tried fixing the wire and had the same problem....so I replaced the shift lever and everything is back to ... no gauges will work in dashboard 1 answer.

No dash gauges, but dash lights - Car Forums and Automotive Chat ...

www.automotiveforums.com > ... > Dodge > Caravan ' Voyager
Feb 6, 2010 - The dash lights work fine, so does everything else. The dash gaugesjust don't work. This is something that has been an intermittent problem ...

Dec 05, 2015 | Cars & Trucks

1 Answer

1994 f150 dash gauges not working


Go to fuse panel left of steering column. Ck to see if #17, 10A fuse, is blown.

Nov 08, 2012 | 1989 Ford F 150

1 Answer

My nissan Almera S reg has no side lights or dash lights.All fuses seem ok.


This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Sep 10, 2012 | 2005 Nissan Almera 1.5

1 Answer

Changing dashboard light


Hi,

This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Aug 09, 2010 | 1998 Plymouth Voyager

1 Answer

Intermittent problem speedo/odometer


would change the ECU with the chip from the key from a car in scrapyard ,but before you get carried away try another seperate earth on the back of the speedo printed circuit board ,i wouldnt mind betting this is your problem

Aug 13, 2009 | 2002 Ford SVT Focus

2 Answers

2001 ram 15oo, speed,tach,oil press,batt,fuel gauges all stopped working at once. message on odometer says--no buS . no noticeable difference in engine performance.


i am having the some problem with my 2001 dodge ram 1500 all of my gauges stop working after the engine light came on now on myodometer says no bus, Can you help me with it

Jul 17, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Odometer reads no bus


check bulkhead connecter for corrosion, cluster is your body controll module, losing signal to fuel pump module , and pcm, thios is a communication issue, volt meter wil help, back probe diagnostic connecter, pin 7, white wire, to see if signal is there, GOOD LUCK RDJRP

Jul 16, 2009 | 1999 Dodge Ram

1 Answer

Gauges, Power Windows, Auto Lamps radio interior lights dont work


Sounds like an ignition switch problem, maybe even at the key.

Jan 09, 2009 | 2002 Ford F350 Super Duty DRW Reg. Cab

Not finding what you are looking for?
2007 Dodge Ram 3500 Quad Cab Laramie Logo

Related Topics:

508 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...