Question about 2002 Mitsubishi Lancer

1 Answer

2003 lancer no injector pulse ,no codes displayed when scaned

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 31 Answers

Try a crank sensor, this should work.

Posted on May 25, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a mitsubishi lancer mr 98 coupe 1.8ltr 4G93 engine I have spark have fuel and pressure if I spray some start spray it will start for 5 or so seconds but the injectors are not pulsing ideas?


the injectors are controlled by the ECU so i would have the OBDII codes read as this should pinpoint the sensor/switch that is causing the problem

Jun 28, 2015 | Mitsubishi Cars & Trucks

1 Answer

1998 ck2a lancer 4g15 no go. have replaced dizzy, computer and tps. has spark and injector pulse and timing is fine. any help appreciated


the next thing to check is the fuel system.
is there fuel in the system, the tank, fuel lines. is there fuel pressure at the injectors? check the fuel pump electrical system, the fuse, fuel pump relay, fuel cut off circuit. some factory security system have a fuel inhibitor, that disable the fuel pump circuit!

Sep 11, 2012 | 1998 Mitsubishi Lancer

1 Answer

2002 lancer there is no fuel injector pulse car will crank but will not start


CHECK WITH CODE SCANNER FOR FAULT CODE/CAMSHAFT SENSOR/CRANKSHAFT SENSOR /FUSE/FUEL PUMP RELAY/

Mar 13, 2011 | 2002 Mitsubishi Lancer

3 Answers

Accelerate at 50kph and engine misses /hesitates. what is the fix. cheers Geoff this is a 2.1 v6 X Type


try tune up (plugs n wires, fuel filter etc) if u dont have check engine light on, if u do find out wat the code is

Feb 02, 2011 | 2003 Jaguar X-Type

1 Answer

My 2003 OZ Rally Mitsubishi Lancer is not starting properly. The engine turns and turns but wont start. especially early in the morning when its colder. later in the day i will start it again and it will...


There is no simple answer, there are to many variables. If you have access to a scan tool, pulling the codes should help. Without them its back to old school hunt and peck method. At this point we need to narrow down the problem. You need to test for spark.
  1. Tag and disconnect the spark plug wires from the spark plugs.
  2. Remove the spark plugs and install the spark plug wires to each spark plug.
  3. Ground (do not hold spark plug) the spark plug; check if spark occurs while engine is being cranked.
Crank the engine for no more than 2 seconds at a time to prevent flooding the engine with gasoline.
If you have spark, You will want to make sure you have fuel injector pulse, along with fuel pressure. If you have spark ..simply spray some starting fluid in through the air filter and hold the gas pedal to the floor and crank it over while spraying. If it fires up, you know it is fuel related( fuel pump, regulator, or ECM if no injector pulse) . If you have no spark then look at ignition coil connection and trace through to the distributor( if equipped ). The crank shaft sensor has a tendency to fail on these as well. This should give you a few things to test and check to start you on your way to narrowing it down. If you have no spark then look at ignition coil connection for power and trace through to the distributor( if equipped ). If it is DIS( no distributor). It may be the Crank sensor or the ECU. The crank shaft sensor has a tendency to fail on these as well.
The ECU uses the signal sent from the Crank sensor to trigger the spark and fuel injectors. ( make certain you have checked all fuses)

Nov 02, 2010 | 2003 Mitsubishi Lancer

1 Answer

Mitisbishi Lancer 2003 Radio Code


you will have to go to the dealership to get the code.if you try to enter the wrong code multiple times your radio may permanantly not work

Jan 14, 2010 | Cars & Trucks

1 Answer

I have a p0303 code on my 2003 yukon. i have changed my spark plugs and wire and the problem still exist. can any one help. thanks


A MISS DOESN'T SPARK ONLY,COULD BE FUEL RELATED INJECTOR OR WIRES,INJECTOR PULSE WORST CASE,IF NOT INJECTOR,VAVLE TRAIN ISSUE,ROCKER,PUSH ROD,VALVE,HOPE THIS HELPS

May 18, 2009 | 2003 GMC Yukon Denali

1 Answer

04 lancer no start,no spark or injector pulse.


it sound to me like the modual has fried it self in the distributor if it has you will have no spark or fuel pulse . have you checked the ignition fuses

Mar 24, 2009 | 2004 Mitsubishi Lancer

Not finding what you are looking for?
2002 Mitsubishi Lancer Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...