Question about 2005 Chevrolet Impala

1 Answer

Would like to change on / off switch button in steering wheel for the cruise control on a 2005 impala, how do I remove the steering wheel airbag?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,036 Answers

YOU NEED TO DISABLE AIR BAGS.FIRST. TURN OFF RADIO THEN DISCONNECT NEGATIVE BATTERY CABLE.WAIT 20 MINUTES FOR AIRBAGS DISCHARGE.THEN REMOVE AIRBAG IN THE STEERING BY REMOVING SCREWS BEHIND AIRBAG IN STEERING WHEEL.

Posted on May 25, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need cruise control buttons for 2005 impala


your best thing is used one from the junk yard

Feb 09, 2013 | 2005 Chevrolet Impala

1 Answer

How do I fix my cruise control


first ck fuse for cruise control,if ok ck power to main switch use a omp, amp meter for test, should have battery voltage to and from switch when in on position. if ok your next ck is steering wheel switch. air bag must be removed unhook battery wait five minutes remove airbag hook battery up ck steering wheel switch if ok below steering wheel is cable reel ck yellow connectors on both side for power if all have power to and from go under hood and ck power to cruise unit if ok pcm may not be letting it come on because of engine or trans readings dtcs pending or set can shut off cruise control

Jul 14, 2012 | 2007 Jeep Compass Limited

1 Answer

Replace curise control switch


Do you mean the main cruise control switch in the steering column? If so, you must remove the airbag assembly then there are a couple screws holding the switch to the steering wheel. The electrical connector will unplug from the clockspring (or "spiral cable") assembly.

3_18_2012_7_06_46_pm.gif

Mar 18, 2012 | 2005 Hyundai Tiburon

1 Answer

I want to replace the right hand speed control for the cruise control on my 2008 Chrysler Aspen - any ideas? Anyone!


11_18_2011_12_24_34_am.gif
REPLACING CRUISE CONTROL SWITCH

1.
Disconnect and isolate negative battery cable from battery.

2. Remove airbag module (See AIRBAG REMOVAL below).

3. Remove speed control switch mounting screw and remove switch from steering wheel.

4. Reverse procedure to install.
AIRBAG REMOVAL
1. Disconnect and isolate negative battery cable from battery.

2. From the underside of the steering wheel, remove the two screws that secure the driver airbag to the steering wheel armature.
CAUTION: The horn switch and the clockspring pigtails connected to the back of the airbag module are fragile. Do not pull on these wires to disengage them. These must be handled carefully to prevent damage to the horn switch and/or the clockspring assembly.
3. Pull the driver airbag away from the steering wheel enough to access the three electrical connections on the back of the airbag housing.

4. Disconnect the steering wheel wire harness connector for the horn switch from the horn switch feed pigtail wire connector, which is located on the back of the driver airbag housing.

5. The clockspring driver airbag pigtail wire connectors are secured by integral latches to the airbag inflator connector receptacles, which are located on the back of the driver airbag housing. Depress the latches on each side of the connector insulator and pull the insulators straight out from the airbag inflator to disconnect them from the receptacles.

6. Remove the driver airbag from the steering wheel.

7. Reverse procedure to install.

Nov 17, 2011 | Cars & Trucks

1 Answer

2007 chevy impala LT, horn and cruise control not working. Cruise control is not working, the light does not come on at all. The horn works with the remote starter but not when pushing on the steering...


most likely the clockspring or ribbon assembly inside the steering wheel has a broken spot in it. if you try to do it yourself be careful with the airbag system

Jul 14, 2011 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

How do i replace the cruise control on/off switch on my 1999 alero


TO REMOVE CRUISE CONTROL SWITCH. FIRST TURN OFF RADIO TO KEEP FROM LOSING CODE. DISARM AIRBAG IN THE STEERING WHEEL BY REMOVING NEGATIVE BATTERY CABLE WAIT 20 MINUTES FOR AIRBAG TO DISCHARGE BEFORE REMOVING AIRBAG AND HORN PAD IN STEERING WHEEL.ONCE AIRBAG IN STEERING WHEEL OUT.YOU CAN REMOVE THE CRUISE CONTROL SWITCH.BECAREFUL REMOVING AIRBAG IN STEERING WHEEL CARRY IT AWAY FROM BODY WITH AIRBAG HORN PAD POINTING UP.IF YOU DROP IT.DONT PUT IN BACK IN STEERING COULD DEPLOY ON INSTALLATION.

Nov 14, 2010 | 1999 Oldsmobile Alero

1 Answer

The directionals don't alaways work. I have to push the 4 way button to get them to work again


If your 3rd brake light always works, then the problem is the turn signal switch. To repair, you have to remove the steering wheel and air bag and replace the turn signal switch. If you have radio controls and or cruise controls on the steering wheel it will make a difference in which turn signal switch is the correct one. You will need some specialty tools to do this job such as a steering wheel puller and a compression tool and snap ring tools. Handling the airbag safely is very important, as it can severely injure you. If you have average or more mechanical skills, you can do it.

If the 3rd brake light does not always work, it could be a different problem.

Sep 23, 2010 | 2002 Chevrolet Impala

2 Answers

No cruise control


In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering wheel to access the part. WARNING: Failure to disarm the airbag system can result in an unexpected Airbag deployment and possible serious personnel injury disconnect the battery 30 minutes prior to start of work.

Apr 01, 2010 | 2005 Chevrolet Tahoe

1 Answer

I NEED TO RESET MY 2005 CHEVROLET IMPALA


You will have to pull the steering wheel off and then the turn signal switch, under that is a release pin to remove the lock cylinder. Since you will have to remove the airbag on the wheel obtain and follow exactly the disarming instructions for the airbag system, if it goes off because it was not disarmed then very serious injury can result.

Oct 13, 2008 | 2005 Chevrolet Impala

1 Answer

I need to replace the crusie control buttons


disconnect batt.wait 5 minutes,push brake several times,locate airbag fuse and remove.this is improtant as you will have to remove drivers airbag.there are 2 round plastic caps covering the 2 airbag bolts located at back of steering wheel by the cruise switches.remove caps remove the 2 8mm bolts.remove airbag,set airbag away from you with plastic cover of airbag up.replace switches.reinstall airbag,reinstall fuse.reconnect batt.

Oct 06, 2008 | 2006 Ford Escape

Not finding what you are looking for?
2005 Chevrolet Impala Logo

457 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...