Question about 2006 Pontiac Montana SV6

1 Answer

2005 pontiac sv6 door alarm chimes all the time. how can I disable or bypass the chime?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

On my '07 Montana SV6 was the same problem, I've fix it by moving up to 3 mm. contact plate at the body frame of the rihgt sliding door. If you check the spots on the plate where pins from the door comes to this plate, you will see that they contacting not in a middle. There are two ways to fix: move down pin unit in the door or move up contact plate on frame. For me second way was better. It's manufacture mistake comes sinse 2005 and on right door only.

Posted on Jun 28, 2011

  • Ig Cor Dec 15, 2013

    Than, pull out contact plate from the front side of the door, remove rubber boot from wire side. You will see back side of sliding contacts. Push small plates toward to moving pins, to provide reliable contact. Top one (single in row) sending 2 impulses to body computer to confirm that door lock is closed to 2 clicks. It's easy job, takes less than 1/2 hours, and you don't need to remove inside door panel. Don't foget to lubricate moving contacts and make sure that pins moving freely but always touching side plates to provide permanent electrical contact.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you disable the door chime?


many drivers have dash lights to inform them that a door is open yet they still drive around and then complain about a knock some where in the back
I would check all the door sensors for adjustment and leave the alarm alone as , as annoying as it might be , it might let you know when a child has opened a door without your knowledge and save a life.

Mar 25, 2015 | 2009 Toyota Camry XLE V6

1 Answer

How can I disable the door chime which is triggered every time I open the Drivers door of of my 1996 Lincoln Continental?


Its sensing that there is a key in the ignition. You have to replace the switch in the ignition cylinder that senses a key is inserted. Or alternatively access a wiring diagram and cut the wire from the key sensor to eliminate it.

Oct 27, 2014 | 1996 Lincoln Continental

5 Answers

How do i turn off the annoying seat belt chime?


It is chiming with the seat belt in operation then have it checked out. I you do not wish to wear the seat belt just do it up and sit on it Why anybody would want to turn of a safety alarm is a bit beyond comprehension.

Aug 16, 2014 | 2000 Pontiac Grand Am GT

1 Answer

2005 PONTIAC MONTANA KEY IN IGNITION SECURITY PROBLEM


if the car does not start and the security light is on maybe check out this site.... I have bought a part from them and it fixed my issue.. if u r unsure email them they have great customer service.. also ifn its what I think it is you can install the part yourself

Jul 27, 2014 | 2005 Pontiac Montana SV6

1 Answer

Were is the fuse for door bell


Is the door chime working and you want to disable it or is there no chime at all?First off the door chime comes through the radio speaker,if you need to disable it you will need to cut the wire from the speaker to the chime.If is annoying you can spray foam on it and muffle it .I believe that it uses data bits from the head unit (radio) to function so another way to get rid of it is sort of drastic but change out your head unit.Sorry your question only asked about where the fuse is and to the best of my knowledge is that is is none.

Apr 19, 2014 | 2005 Chevrolet Trailblazer Ext

3 Answers

Faulty seat belt alarm


YOU CAN' DISABLE THE ALARM.IS PART OF SRS SYSTEM.BUY FROM YOU LOCAL DEALER BELT BUKAL ONLY AND REPLACE.IS EASY AND LOW COST.

Mar 28, 2014 | Hyundai Motor 2004 Sonata

2 Answers

Does the bcm control the alarm in a 2006 monte Carlo? I can't seem to get the alarm to go off. I've also noticed that I have no chime and turn signal sounds. I just recently purchased this car and...


The no chime and turn signal has nothing to do with the alarm. You have a issue with power supply to turn flasher and door chime. The alarm consist of The door ajar switch,body control module,front door lock switch,power door lock switch. You need to check your fuse for turn signal and the door chime

Feb 22, 2012 | 2006 Chevrolet Monte Carlo

2 Answers

How do I go about disabeling the alarm/chime in my 2005 Saturn relay. This chime goes off constantly even while I am driving. It originally started with a chime telling me that the rear door was open when...


The problem is likely a bad switch in said door. If you can't fix it now, crawl under the dash, find the chime (should be easy..ding..ding), and unplug it. Please rate me. Thanks

Sep 03, 2011 | Saturn Relay Cars & Trucks

2 Answers

The door chime on our 2005 Saturn Relay Van continuously goes off when you put it in gear. There are no obstructions but the automatic door switch fails to open the door sometimes and other times the chime...


I have a 2006 SV6 with the power sliding doors. The problem that I found was with the contacts on the door ( They are called plungers) the movable pins were losing connection with the fixed part The plunger is very easy to replace if you can find one. The plungers are covered with a rubber cover and is held in place with 2 plastic pins. My Pontiac dealer could not even find one in his books or even a picture of one, and claimed that he had never had anyone come with a door problem. My Chevy dealer said that it came with a wiring harness that is not needed for $154. The cure that I came up with was to take the plunger block apart (it snaps together)and replace the rusted out springs then solder 3" wires to the end of the plunger pins (they solder easy) to the tabs that go to the plug(pop out the tabs or you will melt the plastic. It took about 45 min. now the doors work like new and will never loose contact again

Oct 06, 2009 | 2005 Saturn Relay

6 Answers

Where is the bcm program fuse on a 2005 pontiac montana sv6


The BCM program fuse on a 2005 Montanna SV6 is called something different in the manual. It's called a “Keyless Entry Module” fuse and it is fuse #7. The fuse panel is located on the passenger side on the side of the dash. There is a cover with an indent hole in it to pull the fuse cover off. It's really hard to pull it off and it almost seems like your going to break it when your trying to get if off. Keep pulling, it will come off! On the fuse cover, fuse #7 is labeled " RFA MDLS" which is again different than what is in the manual. I followed the procedure to reprogram my "Key Fob" and within 45secs, I had reprogrammed my key FOB! I was so excited, because, I have been trying locate the BCM fuse for 4 weeks. I think GMC does not want us to know it’s location or name, so you would have to go into a dealership to get your Key Fobs reprogrammed costing about a $100 for a minute of work.
e65ae06.jpg


1. Keep the windows open as a safety measure, then,
2. Remove the ignition key from the ignition lock cylinder.
3. Remove the “RFA MDLS” (fuse #7 ,BCM PRGRM fuse, Keyless Entry fuse) from the fuse panel.
4. Close all of the doors.
5. Close the liftgate.
6. Turn the ignition lock cylinder to ACC.
7. Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second.
8. Open and close any vehicle door. A chime will be heard when the system enters the BCM programming/diagnostic mode.
9. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
10. Important
After 7 seconds, a chime may be heard confirming successful programming.
11. Repeat the previous step on each additional transmitter to be programmed.
12. Remove the ignition key from the ignition lock cylinder
13. Install the “RFA MDLS” fuse ( fuse #7 ,BCM PRGRM fuse, Keyless Entry fuse) back into the fuse panel.
14. Press on the key fob functions (EG. Lock, Unlock) to verify correct operation.

Mar 17, 2009 | 2006 Pontiac Montana SV6

Not finding what you are looking for?
2006 Pontiac Montana SV6 Logo

2,233 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...