Question about 2006 Jeep Grand Cherokee

Open Question

Front Differential Actuator. How do I replace the axle locker actuator? I was told by dealership that I need to replace due to "service 4wd System" indicator that stays on constant. Any advice greatly appreciated. Part number is 52114003 AF. The technician said that he ran a flash and upgraded from AF to AM (I'm assuming this is a version control of sort). 2006 Jeep Grand Cherokee Limited 5.7L Hemi

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2005 Jeep Grand Cherokee (HEMI) Service Electric Brake System

Problem is a faulty Steering Angle Sensor (part of Steering Module) located in steering column ...replacement part $600.00.

Posted on Apr 16, 2009

Ad
  • 1 Answer

SOURCE: Front wheels do not turn

I did run the vehicle on the lift in 4wd. The actuator is trying to engage. I removed the right side axle housing and found the shim on the end of the shaft had fallen out of place. The small roller bearing in the shaft was damaged as well. This may have happended on a previous axle seal replacement. A new shim, and bearing fixed the problem. Thanks for our reply

Posted on Nov 28, 2008

csmock132
  • 4669 Answers

SOURCE: 4wd not engaging

Is it a two wire actuator or a three wire actuator? The two wire ones are pretty unreliable. that is why Chevrolet converter them to the three wire. Check for power and ground on the two wire in 4wd. For the three is should have one ground wire, one wire that is hot in 4wd, and one wire that is hot in 2wd.

Posted on Mar 02, 2009

  • 12 Answers

SOURCE: replacing 4WD actuator

It is located by the front pumpkin should be 4 bolts I believe that hold it in and 1 connector

Posted on May 28, 2009

robslac24
  • 2 Answers

SOURCE: 01 Chevy Silverado 4 X 4 not working. 4WD light

Having the same exact problem but with my 1999 escalade. Thought it was the actuator bought a new one installed it transfer case would engage but front end wouldnt lock. Took it out of housing left it plugged in got a friend to go through all the 4wd for me and the plunger never moved out the actuator. Checked my wiring harness which is a four prong ann it had one hot prong like it is suppose to. Traced wires even replaced dash switch same problem. Taking it to local dealership tom to have it checked for codes. I was told it could be the transfercase actuator even though its workin that actuator is what sends power to the front to engage the actuator to lock the differential.

Posted on Sep 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I got a 96 chevy 4x4 and my front wheels aren't pulling. i replaced the acuator and still nothing. everything sounds like it is engaging but no turning of the front wheels. do 96 models have auto locking...


96 chevys have a ifs (independent front suspension) this give it more ground clearance but does not have lock out hubs, the cv axles go into the front differential an spin freely until you put it in 4wd, how this works is your transfercase spins the drive shaft that goes into the front differential an while you put it in 4wd it sends power to the actuator to lock the front differential. if your front end isnt pulling you either popped your 1 of your cv axles but if you did this you would know because it makes a very loud thunking noise while you're driving, my guess is you have a short thats not sending power to the actuator. check to see if the wiring harnesses are connected and check if the fuse that operates the 4wd in the cab of the truck is not blown. also actuators for these trucks are horrible they go out alot

Feb 11, 2011 | 1986 Chevrolet K1500

2 Answers

Four wheel drine willnot work front end making noise


Fuse is located at the end of eh dash on drivers side and the Actuator is located at the front differential and on the passenger side.
When in 4wd mode, a switch on top of the transfer case conducts 12 volts out to the actuator. Wire #50 (brown) is the 12v feed, and it conducts to the light blue wire (#900) to the actuator.
When shifted out of 4wd, the switch opens up and no voltage goes to the actuator.

Check voltage at the connector for the front actuator (at the front differential - it looks like a large bullet that threads into the front diff.) If it has 12 volts, the actuator is the problem. If it does not have 12 volts, check the transfer case switch and the power feed to the transfer case.

I'll assume it is the actuator, if the plug to the actuator is getting 12 volts when in 4wd.
The way this actuator works, is it is a sealed chamber that gets heated by voltage. When it heats, the pin in the end swells and pushes a shift fork in the front differential. The shift fork engages a spline on the passenger side of the differential, and boom! you have 4WD.

GM offered an upgrade to this actuator that is a motor instead of a heated device. However, it requires a small harness addition, a spacer, and a new actuator. It is about a $150 to $200 option.

Good luck. The actuator is usually the problem 90% of time but recheck all of the wire harness just to maker sure there is no short before replacing any parts. The actuator may not be fully engaged or disengaged and the fork to the spline may be what is causing the grinding.

88-UP C/K ACTUATOR UPGRADE
VEHICLE SERVICED: 88-99 CHEVROLET FULL SIZE
PURPOSE: IMPROVE AXLE CONNECT ENGAGEMENT TIME AND
COMPONENT RELIABILITY.

SYMPTOMS: NO FRONT DRIVE AXLE ENGAGEMENT WHEN SHIFTED INTO 4X4.

Obtain the following GM part numbers:
(1) 26060073 Actuator
(1) 88959465 Harness/Spacer Kit

Mar 06, 2010 | 1996 GMC Yukon

2 Answers

I have a 2002 Chevy Silverado 8 cylinder 4wd extended cab. It has the push button shifter for 4wd. When I try to use 4WD Auto or 4WD Hi, the indicator lights come on but the 4wd does not engage. I read...


Fuse is located at the end of eh dash on drivers side and the Actuator is located at the front differential and on the passenger side.
When in 4wd mode, a switch on top of the transfer case conducts 12 volts out to the actuator. Wire #50 (brown) is the 12v feed, and it conducts to the light blue wire (#900) to the actuator.
When shifted out of 4wd, the switch opens up and no voltage goes to the actuator.

Check voltage at the connector for the front actuator (at the front differential - it looks like a large bullet that threads into the front diff.) If it has 12 volts, the actuator is the problem. If it does not have 12 volts, check the transfer case switch and the power feed to the transfer case.

I'll assume it is the actuator, if the plug to the actuator is getting 12 volts when in 4wd.
The way this actuator works, is it is a sealed chamber that gets heated by voltage. When it heats, the pin in the end swells and pushes a shift fork in the front differential. The shift fork engages a spline on the passenger side of the differential, and boom! you have 4WD.

GM offered an upgrade to this actuator that is a motor instead of a heated device. However, it requires a small harness addition, a spacer, and a new actuator. It is about a $150 to $200 option.

Good luck. The actuator is usually the problem 90% of time but recheck all of the wire harness just to maker sure there is no short before replacing any parts. The actuator may not be fully engaged or disengaged and the fork to the spline may be what is causing the grinding.

88-UP C/K ACTUATOR UPGRADE
VEHICLE SERVICED: 88-99 CHEVROLET FULL SIZE
PURPOSE: IMPROVE AXLE CONNECT ENGAGEMENT TIME AND
COMPONENT RELIABILITY.

SYMPTOMS: NO FRONT DRIVE AXLE ENGAGEMENT WHEN SHIFTED INTO 4X4.

Obtain the following GM part numbers:
(1) 26060073 Actuator
(1) 88959465 Harness/Spacer Kit

Feb 03, 2010 | 2002 Chevrolet Silverado

1 Answer

Whenever I shift my 1988 K-3500 in to 4hi or 4low the fuse blows and will not engage into 4 wheeldrive. Any ideas on this?


On the full size, the front actuator is electric, not vacuum.

When in 4wd mode, a switch on top of the transfer case conducts 12 volts out to the actuator. Wire #50 (brown) is the 12v feed, and it conducts to the light blue wire (#900) to the actuator.
When shifted out of 4wd, the switch opens up and no voltage goes to the actuator.

Check voltage at the connector for the front actuator (at the front differential - it looks like a large bullet that threads into the front diff.) If it has 12 volts, the actuator is the problem. If it does not have 12 volts, check the transfer case switch and the power feed to the transfer case.

I'll assume it is the actuator, if the plug to the actuator is getting 12 volts when in 4wd.
The way this actuator works, is it is a sealed chamber that gets heated by voltage. When it heats, the pin in the end swells and pushes a shift fork in the front differential. The shift fork engages a spline on the passenger side of the differential, and boom! you have 4WD.

GM offered an upgrade to this actuator that is a motor instead of a heated device. However, it requires a small harness addition, a spacer, and a new actuator. It is about a $150 to $200 option.

Good luck. The actuator is usually the problem 90% of time but recheck all of the wire harness just to maker sure there is no short before replacing any parts. The actuator may not be fully engaged or disengaged and the fork to the spline may be what is causing the grinding.

88-UP C/K ACTUATOR UPGRADE
VEHICLE SERVICED: 1994 CHEVROLET FULL SIZE
PURPOSE: IMPROVE AXLE CONNECT ENGAGEMENT TIME AND
COMPONENT RELIABILITY.

SYMPTOMS: NO FRONT DRIVE AXLE ENGAGEMENT WHEN SHIFTED INTO 4X4.

Obtain the following GM part numbers:
(1) 26060073 Actuator
(1) 88959465 Harness/Spacer Kit

Jan 25, 2010 | 1989 Chevrolet S-10 Blazer

2 Answers

The 4x4 do not engage on my 1990 chevy pick up what do i need to check first


On the full size, the front actuator is electric, not vacuum.

When in 4wd mode, a switch on top of the transfer case conducts 12 volts out to the actuator. Wire #50 (brown) is the 12v feed, and it conducts to the light blue wire (#900) to the actuator.
When shifted out of 4wd, the switch opens up and no voltage goes to the actuator.

Check voltage at the connector for the front actuator (at the front differential - it looks like a large bullet that threads into the front diff.) If it has 12 volts, the actuator is the problem. If it does not have 12 volts, check the transfer case switch and the power feed to the transfer case.

I'll assume it is the actuator, if the plug to the actuator is getting 12 volts when in 4wd.
The way this actuator works, is it is a sealed chamber that gets heated by voltage. When it heats, the pin in the end swells and pushes a shift fork in the front differential. The shift fork engages a spline on the passenger side of the differential, and boom! you have 4WD.

GM offered an upgrade to this actuator that is a motor instead of a heated device. However, it requires a small harness addition, a spacer, and a new actuator. It is about a $150 to $200 option.

Good luck. The actuator is usually the problem 90% of time but recheck all of the wire harness just to maker sure there is no short before replacing any parts. The actuator may not be fully engaged or disengaged and the fork to the spline may be what is causing the grinding.

88-UP C/K ACTUATOR UPGRADE
VEHICLE SERVICED: 1994 CHEVROLET FULL SIZE
PURPOSE: IMPROVE AXLE CONNECT ENGAGEMENT TIME AND
COMPONENT RELIABILITY.

SYMPTOMS: NO FRONT DRIVE AXLE ENGAGEMENT WHEN SHIFTED INTO 4X4.

Obtain the following GM part numbers:
(1) 26060073 Actuator
(1) 88959465 Harness/Spacer Kit

Jan 20, 2010 | 1992 Chevrolet K1500

2 Answers

I have a 2002 Chevy Tahoe making a grinding noise in the front drivers side wheel, what could this possibly be?


If 4wd Tahoe, it is the CV joint going out or is out, replace part about 250 bucks, very common in 4wd Tahoe

Jan 11, 2010 | 2000 Chevrolet Tahoe

1 Answer

1991 K2500 pickup, 350tbi,4l80 trans, 4wd not working, I have gotten it to turn on a couple of times but it never stays working. The transfer case does lock in when its put into 4wd. also the actuator is...


On the full size, the front actuator is electric, not vacuum.

When in 4wd mode, a switch on top of the transfer case conducts 12 volts out to the actuator. Wire #50 (brown) is the 12v feed, and it conducts to the light blue wire (#900) to the actuator.
When shifted out of 4wd, the switch opens up and no voltage goes to the actuator.

Check voltage at the connector for the front actuator (at the front differential - it looks like a large bullet that threads into the front diff.) If it has 12 volts, the actuator is the problem. If it does not have 12 volts, check the transfer case switch and the power feed to the transfer case.

I'll assume it is the actuator, if the plug to the actuator is getting 12 volts when in 4wd.
The way this actuator works, is it is a sealed chamber that gets heated by voltage. When it heats, the pin in the end swells and pushes a shift fork in the front differential. The shift fork engages a spline on the passenger side of the differential, and boom! you have 4WD.

GM offered an upgrade to this actuator that is a motor instead of a heated device. However, it requires a small harness addition, a spacer, and a new actuator. It is about a $150 to $200 option.

Good luck. The actuator is usually the problem 90% of time but recheck all of the wire harness just to maker sure there is no short before replacing any parts.

88-UP C/K ACTUATOR UPGRADE
VEHICLE SERVICED: 1994 CHEVROLET FULL SIZE
PURPOSE: IMPROVE AXLE CONNECT ENGAGEMENT TIME AND
COMPONENT RELIABILITY.

SYMPTOMS: NO FRONT DRIVE AXLE ENGAGEMENT WHEN SHIFTED
INTO 4X4.

Obtain the following GM part numbers:
(1) 26060073 Actuator
(1) 88959465 Harness/Spacer Kit

Jan 10, 2010 | 1991 Chevrolet K2500

1 Answer

4x4 locks in ok but when locked in it real loads also shimmy and ginds just some times on the front end


On the full size, the front actuator is electric, not vacuum.

When in 4wd mode, a switch on top of the transfer case conducts 12 volts out to the actuator. Wire #50 (brown) is the 12v feed, and it conducts to the light blue wire (#900) to the actuator.
When shifted out of 4wd, the switch opens up and no voltage goes to the actuator.

Check voltage at the connector for the front actuator (at the front differential - it looks like a large bullet that threads into the front diff.) If it has 12 volts, the actuator is the problem. If it does not have 12 volts, check the transfer case switch and the power feed to the transfer case.

I'll assume it is the actuator, if the plug to the actuator is getting 12 volts when in 4wd.
The way this actuator works, is it is a sealed chamber that gets heated by voltage. When it heats, the pin in the end swells and pushes a shift fork in the front differential. The shift fork engages a spline on the passenger side of the differential, and boom! you have 4WD.

GM offered an upgrade to this actuator that is a motor instead of a heated device. However, it requires a small harness addition, a spacer, and a new actuator. It is about a $150 to $200 option.

Good luck. The actuator is usually the problem 90% of time but recheck all of the wire harness just to maker sure there is no short before replacing any parts.

88-UP C/K ACTUATOR UPGRADE
VEHICLE SERVICED: 1994 CHEVROLET FULL SIZE
PURPOSE: IMPROVE AXLE CONNECT ENGAGEMENT TIME AND
COMPONENT RELIABILITY.

SYMPTOMS: NO FRONT DRIVE AXLE ENGAGEMENT WHEN SHIFTED
INTO 4X4.

Obtain the following GM part numbers:
(1) 26060073 Actuator
(1) 88959465 Harness/Spacer Kit

Jan 09, 2010 | Chevrolet Silverado 1500 Cars & Trucks

4 Answers

4wd switches blinking and wont engage


the 4 wheel drive switch is an extremely high failure part. i would replace it and you should be ok! hope this info helps!

Sep 22, 2009 | 1996 Chevrolet K1500

1 Answer

01 Chevy Silverado 4 X 4 not working. 4WD light


Having the same exact problem but with my 1999 escalade. Thought it was the actuator bought a new one installed it transfer case would engage but front end wouldnt lock. Took it out of housing left it plugged in got a friend to go through all the 4wd for me and the plunger never moved out the actuator. Checked my wiring harness which is a four prong ann it had one hot prong like it is suppose to. Traced wires even replaced dash switch same problem. Taking it to local dealership tom to have it checked for codes. I was told it could be the transfercase actuator even though its workin that actuator is what sends power to the front to engage the actuator to lock the differential.

May 12, 2009 | 2001 Chevrolet Silverado 1500

Not finding what you are looking for?
2006 Jeep Grand Cherokee Logo

Related Topics:

638 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...