Question about 2005 GMC Sierra Denali

1 Answer

My blower motor resistor burned up I'n my 05

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 288 Answers

Are you putting the right amp fuse in place of that fuse was at ? If you have a fuse that is 5 amps smaller could produce this same problem so go make sure your manual says what amp fuse goes there first. This might solve the issue. Usually if the fuse keeps breaking inside of it means that there might be a short some where else.

Posted on May 24, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ac and heater fan is burned out I want to replace it but don't know how to dissemble it 2004 gmc Denali


This is an easy one, in the picture there you will see the resistor, that is the small box with wires to blower, remove that first. also are you sure it is the blower? 90% of the time is the resistor that goes bad, unplug connector from turn the key on until all dash lights come on or start the truck, use a test light and one of the connector wires from the connector you that you unplugged from the blower should have power, the other connector on that plug is the ground and is controlled through the resistor, mark the power wire and then plug back into blower, then use a jumper wire connect one end to a good ground. a paint less area (metal).the other end connect to blower, make sure not to connect to the wire you have power in, and see if blower runs, you may see a small spark when connecting but that is normal. if blower runs replace resistor.

To replace the blower you will unplug connector to blower, remove resistor first just to get it out of the way, some models have an insulator cover over the blower, if so remove the screws and remove the cover next remove the connector, next you will see a tab, hold down tab and turn blower motor counter clock wise to remove from box,blower should drop right out, just make a ref mark on the blower and heater box so when installing new one in goes in correctly, i always note where the plug is and use that as a ref mark, if it is the blower and not the resistor then replace blower with the fan, if you want to just replace the motor and not the fan then remove the nut or clamp which ever one it has and have some one hold fan by its sides and you use a small punch and hammer and tap on stud and allow motor to fall , let me know the out come. good day....

Dec 24, 2012 | Cars & Trucks

1 Answer

Hello I have a 2005 gmc Yukon Denali. The other day it rained heavily. The next morning I went to work and noticed my ac blower wasnt working. So I tested it and the motor ran but I did find that my...


check the wires with a multimeter to see if there might be a short. put the multimeter where the fuse is at to see why the fuse is being dead. but make sure you know what you are doing first with multimeter or have someone else that knows how to use the multimeter.

May 24, 2011 | 2005 GMC Sierra Denali

1 Answer

Hello I have a 2005 gmc Yukon Denali. The other day it rained heavily. The next morning I went to work and noticed my ac blower wasnt working. So I tested it and the motor ran but I did find that my...


There is a short to power well you found one of the problems and that was the area that is wet, so let that dry, and if you have electrical cleaner (spay can type) just follw the direction on the container, and yes you will need to have the switch replaced those 2 component you found is the source of the problem

May 22, 2011 | 2005 GMC Sierra Denali

1 Answer

I have a 2005 gmc Denali and my blower resistor burned up. I went and bought a brand new one and a brand new pig tail because apparently the aftermarket one is diff. Any ways I pit it back I'n and it...


Hi, often the switch will fail first and then cause the resistor to fail. The way this happens is the switch may engage multiple speeds and thus cause excessive current through the resistors. You can check the switch at the resistor pigtail using an voltmeter or 12 volt test light. Each terminal in the connector should have power with one and only one setting of the switch. If more than one terminal has power for any switch setting, replace the switch. Please let me know if you need instructions or have any more questions, and thanks for using FixYa.
jturcotte_1742.gif

May 22, 2011 | 2005 GMC Sierra Denali

1 Answer

Blower motor won't work, even with new motor.


Hello Travis.
If yours is dual zone, I believe the resistor (blower control module) is a solid state. Did you check it using the fan speed selector and test the voltage output on the purple wire?
The gray black wire going into the resistor is a variable voltage output from the heater control panel. This signal is amplified by the resistor/blower control module.
The black wire out of the resistor also needs proper good ground.
There is a fuse in the underhood relay/fuse panel that feedback from the resistor output to the blower (purple wire) is also fed back to the heater control panel. Verify this fuse is good.

When blower motors go bad they will often absorb a lot of electrical current. This current has to go through the blower control/resistor and will often burn them out due to the heat developed from the high current load.
These resistors are also mounted in the airflow out of the fan motor to help cool them so if the fan is still drawing current and not blowing the resistor overloads and burns it out.
Not sure how you tested the resistor but I suspect yours is faulty.
If you would like more advise let me know.

KL


Jan 04, 2010 | 1993 Buick LeSabre

1 Answer

2003 yukon denali---relay locate for blower


the relay is built into the speed resistor or motor control module ) depends if you have automative or manual heater controls. is automatic it will be motor control module and manual is the resistor module. these units are located beside the heate fan motor. the motor helps keeps the unit cool. just unbolt the module, unplug it and install new one. Just check to make sure the connector is good.. The heat created by the connection sometimes melts the power or ground leads (red or black) and if this is so you will need to replace the pin.

Sep 01, 2009 | 2003 GMC Yukon Denali

1 Answer

1999 yukon denali front blower motor not working


Check Fuse #3 in the under hood fuse block it is the only common connection I can make.

Jun 28, 2009 | 1999 GMC Yukon Denali

2 Answers

Blower for Heat/A/c not working


Blower Motor Resistor Replacement Removal Procedure
  1. If equipped, remove the IP sound insulator.

  2. 476821.gif

  3. Disconnect the electrical connection from the blower motor.
  4. Disconnect the electrical connection from the blower motor resistor.

  5. 382493.gif

  6. Remove the blower motor resistor retaining screws.

  7. 382503.gif

  8. Remove the blower motor resistor.
Installation Procedure

    382503.gif
  1. Install the blower motor resistor.

  2. 382493.gif

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  3. Install the blower motor resistor retaining screws.
  4. Tighten
    Tighten the screws to 1.6 N·m (14 lb in).

    476821.gif

  5. Connect the electrical connection to the blower motor resistor.
  6. Connect the electrical connection to the blower motor.
  7. If equipped, install the IP sound insulator.

Dec 08, 2008 | 2001 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...