Question about 1995 Chevrolet Camaro

1 Answer

When i start my car oil squirts up out of the motor where could it be coming from

Posted by on

  • robertwilk896 May 24, 2011

    where is the oil coming from>I would clean motor thourly then after you start it again recheck for oil leak work from valve covers down



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 984 Answers


Let's start by telling you how to diagnose the problem.

Most oil leaks are easily located and repaired by visually finding the leak and replacng or repairing the necessary parts. On some occasions a fluid leak may be difficult to locate or repair. The following procedure may help in locating and repairing most leaks.

Finding the Leak

  • Identify the fluid, determine whether it is engine oil, automatic transmission fluid, power steering fluid, etc.
  • At what location or point is the fluid leaking from? After running the vehicle at normal operating temperature, park the vehicle over a large sheet of paper, After a few minutes, you should be be able to ascertain the approximate location of the leak by the drippings on the paper.
  • Visually check around the suspected component. Check around all gasket mating surfaces and hoses for leaks. If your car provides engine oil cooling, check the oil lines leading to the radiator. A mirror is useful for finding leaks in areas that are hard to reach. If the leak still cannot be found, it may be necessary to clean the suspected area with a degreaser, steam or spray solvent. Most car washes provide this service or make it possible for you to do it yourself. Clean the area well, then dry the area. Operate the vehicle for several miles at normal operating temperatures and varying speeds. After operating the vehicle , visually check the suspected component. If you still cannot locate the leak, try using the power method.

The Power Method
  • Clean the suspected area.
  • Apply an aerosol-type powder, e.g., face powder, to the suspected area.
  • Operate the car under normal operating conditions.
  • Visually inspect the suspected component. You should be able to trace the leak path over the white powder surface to the source.

Good luck and all the best


Posted on May 24, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1997. Why has it started sputtering?

The oil is a sign of a problem and the plug may be fouling. A compression test is a start. Generally a squirt of oil will increase compression readings in the bad cylinder during a compression test if an oil ring is at fault. If there is no change with the squirt of oil, it is a valve stem seal or a head gasket problem.

Jul 13, 2015 | Mercury Grand Marquis Cars & Trucks

3 Answers

2001 ford F250 diesel i was driving lost power pulled over i shut it off started it drove about 50 yards it did the same thing after sitting over night I start it runs maybe 2 min clunking sound from motor...

Sounds like fuel pump. There's a 'valve stem' looking nipple on the gas line going to your cylinders. Push in the stem in the middle. If the fuel pump works you will have pressure and the gas will squirt out. If it squirts just a little and quits, then you're not getting any gas pressure. It could also be your in-line fuel filter.

Feb 28, 2015 | 2001 Ford F-250 Super Duty

1 Answer

1996 vortec 5.7. how do I adjust rocker arms when the motor is cold?

these are adjusted the same way 5.7 litre motors have been adjusted since GM started making this size of motor. with every thing in place tighten rocker nuts down until about 1/16" threads is protruding above nut. once the car starts allow the engine pressure to build and oil is squirting around rockers. then with engine running tighten down rockers that are noisy until the noise has just gone. then back off nut until it starts to clatter then tighten 3/4 of a turn. repeat to all the other rockers and your done.

Jan 08, 2013 | Chevrolet 1500 Cars & Trucks

1 Answer

Hydraulic throwout bearing

it is dirty brake fluid that squirts out bleed it until clean fluid come threw

Sep 02, 2012 | 1990 Jeep Wrangler

1 Answer

I haven't started my 1988 Chevy 305 truck in a few years. I put a squirt of lubricate in each cylinder, made sure there was oil and coolant, and a new battery. When I tried to turn the key it wou

I would check to see if you are getting 12 volts at the starter. You should have one wire coming from the ignition that gets system voltage when you turn the key to the start position. You'll also have one from the battery that will be hot all the time.

Dec 21, 2017 | 1988 Chevrolet K2500

1 Answer

Oil is squirting out a stream between the starting motor and starter solenoid


Aug 07, 2011 | Oldsmobile Achieva Cars & Trucks

1 Answer

Car starts, while car is running, oil squirt below the header

Look in the oil filter area to see if the oil sender is leaking. You will have to jack the car up with the jackstand in place. Look for oil leak in the area of the oil filter. Oil senders leak all the time and have seen motors burn out because of them. Hope this helps leave comment

Apr 11, 2010 | 1999 Chevrolet Venture

3 Answers

Fluid squirting out of the top part of an engine

sounds like a hose or gasket has blown

Dec 24, 2009 | 1995 Geo Metro

1 Answer


Before you start it up you need to pull the spark plugs and squirt a few drops of motor oil or Marvel Mystery Oil into each cylinder. As long as the plugs are out you might as well replace them, especially if they've seen much use.

Dec 04, 2009 | 1988 Mazda 929

1 Answer

Stalls because lack of gas going to the motor

squirt some oil from a conventional oil can around the linkage with engine oil in it none of this crappy spray stuff

Feb 13, 2009 | 2001 Cadillac DeVille

Not finding what you are looking for?
1995 Chevrolet Camaro Logo

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides