Question about 2002 Toyota Land Cruiser

Open Question

Location of camshaft position sensor A on a 2002 landcruiser

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
fastboyz
  • 674 Answers

SOURCE: 2002 saturn sl1 camshaft position sensor

I hate to tell you this, but there is not Camshaft Position Sensor on any 1.9L Single or Dual OHC. I assume you had someone read a Diagnostic Trouble Code from your PCM. They probably told you that you needed a Camshaft Position Sensor, and then offered to sell you one. I would recommend changing your spark plugs and your plug cables with FACTORY REPLACEMENTS. This will usually make the DTC go away. Aftermarket plugs and wires rarely work well for this engine. If you are looking for a CRANKSHAFT position sensor, look between the engine and transmission on the back side of the transmission. It is also known as the "transmission input speed sensor". More often than not though, your engine will not fire up if the Crank position sensor is not working. Hope this helps.

Posted on Aug 24, 2008

Ad
savdragon
  • 37 Answers

SOURCE: locate camshaft sensor 2002 chevy trailblazer

Assuming you have a 4.2L engine here is the location.
b3031ef.gif

Hope this helps out,
if so please rate my answers.
Brett

Posted on Mar 19, 2009

emissionwiz
  • 76848 Answers

SOURCE: camshaft position sensor location

At the right rear of the engine under the intake manifold and to the left of the oil filter. You will probably need to go under the car to spot it, it's the sensor with a three-wire connector arranged vertically. But you can take it out from above. It's held in with a single bolt with an eight MM head located just above the sensor. Un-clip and remove the electrical connector. Unscrew the bolt with a socket wrench & extension bar. Wiggle and pull the sensor out.
here is a picture.
255f615.jpg

Posted on Apr 10, 2009

  • 144 Answers

SOURCE: Where is the camshaft position sensor located in a 2001 VW Passat

when you are looking at the engine pull off the plastic cover on top then the front cover that covers you timing belt there is a wire harness tha goes right to it in the left upper coner two ten mil bolts and it comes off careful not to drop bolts down in belt that could be bad. it is that easy

Posted on Sep 01, 2009

  • 26 Answers

SOURCE: camshaft position censor 98 rav4

One item to think about:

You must clear the code with an OBD tester or the light will not extinguish...even with the issue fixed.

The is much info on the cam position sensor on the Rav4 forums including pictures and discussions.

Posted on Oct 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of camshaft position sensor on a 2002 oldsmobile bravada


4200 vortec, Its located in front of engine, its just below the engine oil fill cap, right by the coolant hose is the camshaft position sensor (CMP)
If your looking for the camshaft positioning actuator solenoid its location is on the exhaust manifold side on the top right corner of the cylinder head, if your looking at the motor from the exhaust side, its behind the power steering fill. You have to remove the belt to loosin the power steering pump through the pulley then kind of push it aside as you take out the camshaft actuator solenoid.

Feb 29, 2016 | 2002 Oldsmobile Bravada

1 Answer

2002 isuzu rodeo 2.2 liter code P0341 cmp range or performance problems


P0341 ISUZU - Camshaft Position Sensor Performance
Possible causes- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Sep 10, 2012 | 2002 Isuzu Rodeo

2 Answers

Would like to know where the Cam Shaft Sensor is located in 2002 Trailblazer.


it is the sensor that is being pointed at in the cylinder head


9a01378.jpg

Sep 12, 2010 | 2005 Chevrolet TrailBlazer

1 Answer

How do I change a camshaft position sensor on a 2002 Trailblazer?


Hi : Your CPS (Camshaft position sensor) is located on the Engines Front Cover (Timing Chain Cover) its right below your Cylinder Head ,Get a Good Bright Light to Locate it ,You'll see a Wiring Connector plugged into the Sensor, emove the electrical Plug.
Then you have 1- Screw Holding it in Place -Remove the Retaining Screw and Remove the Sensor.

To replace it with your new Camshaft Sensor Put the Camshaft Sensor in where you took out your Old one,Replace the Retaining Screw Tighten up Good And Snug,Put the Wiring connector back on the Sensor and Your Done. This will get your job done,Let me know Please how My Solution/instructions have Helped you. Thanks From d_hubbs

Jun 08, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

Where crank shaft and camshaft?


The camshaft position sensor is located on the timing cover, near the top of the motor. The crankshaft position sensor is located on the same timing cover near the crankshaft. Just a side note, more than likely the crankshaft position is your issue and it's under a recall from Nissan and they will replace it for free.

May 23, 2009 | 2002 Nissan Altima

1 Answer

Ineed to know the location of the cam sensor on a ford escape 2002 with the 3.0 liter V6 DOHC


SECTION 303-14: Electronic Engine Controls 2002 Escape Workshop Manual REMOVAL AND INSTALLATION Camshaft Position (CMP) Sensor —3.0L (4V) Removal and Installation
  1. Remove the camshaft position (CMP) sensor.
    1. Disconnect the electrical connector.
    1. Remove the bolt.
    1. Remove the sensor.
4544c22.gif
#56 is the cam sensor. please rate as fixed if this is what you need.

231ee68.gif

May 02, 2009 | Ford Escape Cars & Trucks

1 Answer

2002-2004 Mitsubishi Eclipse Camshaft Position Sensor Location?


would this sensor make the car not start when it is hot?

Apr 22, 2009 | 1996 Mitsubishi Eclipse

2 Answers

2002 saturn sl1 camshaft position sensor


I hate to tell you this, but there is not Camshaft Position Sensor on any 1.9L Single or Dual OHC. I assume you had someone read a Diagnostic Trouble Code from your PCM. They probably told you that you needed a Camshaft Position Sensor, and then offered to sell you one. I would recommend changing your spark plugs and your plug cables with FACTORY REPLACEMENTS. This will usually make the DTC go away. Aftermarket plugs and wires rarely work well for this engine. If you are looking for a CRANKSHAFT position sensor, look between the engine and transmission on the back side of the transmission. It is also known as the "transmission input speed sensor". More often than not though, your engine will not fire up if the Crank position sensor is not working. Hope this helps.

Aug 24, 2008 | 2002 Saturn Sl

Not finding what you are looking for?
2002 Toyota Land Cruiser Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...