Question about Chevrolet Blazer

Open Question

Intake manifold torq spec and sequence for a 2001 4.3 s10 blazer

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Torque and sequence to Intake Manifold for 3.3L Nissan Xterra 2000

Hi El Faraon,
I believe that you're dealing with 12 mm bolts and nuts....THESE ARE NOT THE SPECS FOR YOUR ENGINE, but I believe that if you use them you'll be close....Tighten in three stages up to 22nm....choose the bolts from the centre of the manifold and circle outwards until you reach the last one.....It may be a good idea to draw an overhead or plan view of the unit, marking out the bolt positions.....Start at the centre and mark the sequence and follow that....What is important is starting at the centre, so that nothing becomes warped....

Hope this helps,

Regards, Johngee10

Posted on Sep 06, 2008

Ad
chuck943
  • 783 Answers

SOURCE: Ford 460 Intake Manifold Torque spec

22 to 35 ft lbs

Posted on May 22, 2009

  • 60 Answers

SOURCE: how to change an intake manifold gasket on a 2001

I suggest buying a haynes or chilton manual for your truck it will give you step by step instructions.

Posted on Oct 03, 2009

  • 279 Answers

SOURCE: looking for torque specs and sequence of both

Lower intake bolts 11 ft. lbs start in the center of the intake and work your way out cross from side to side.Tighten the upper intake bolts with the same procedure with 89 inch pds.Be sure to apply threadlocker to the lower intake bolt threads.

Posted on Feb 07, 2010

emissionwiz
  • 76691 Answers

SOURCE: need torque specs for a 2001 jeep cherokee intake

attached is the picture of the torque sequence for bolts and the torque specs. as u can see different bolts have diff specs for torque


c45631a.jpg

Posted on May 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs and sequence for the intake and head gasket on a 1999 Chevy Silverado 6.0l V8 K2500


Cylinder Head Bolts (First Pass all M11 Bolts in Sequence)
30 N?·m
22 lb ft
Cylinder Head Bolts (Second Pass all M11 Bolts in Sequence)
90 degrees
Cylinder Head Bolts (Final Pass all M11 Bolts in Sequence-Excluding the Medium Length Bolts at the Front and Rear of Each Cylinder Head)
90 degrees
Cylinder Head Bolts (Final Pass M11 Medium Length Bolts at the Front and Rear of Each Cylinder Head in Sequence)
50 degrees
Cylinder Head Bolts (M8 Inner Bolts in Sequence)
30 N?·m
22 lb ft
Intake Manifold Bolts (First Pass in Sequence)
5 N?·m
44 lb in
Intake Manifold Bolts (Final Pass in Sequence)
10 N?·m
89 lb in
Intake Manifold Wiring Harness Stud
10 N?·m
89 lb in

Oct 27, 2015 | Cars & Trucks

1 Answer

Intake Manifold tightening sequence plus torque specs


start in the middle and alternate left to right and the torque on a alloy manifold will be around 14lbs or a nip with a 3/8th drive rachet ,any water passages use contact adhesive around the water ports .

May 25, 2012 | Chevrolet Corsica Cars & Trucks

1 Answer

What is the torque specifications and sequencing for the intake manifold on a 1998 Chevy blazer?


zjlimited_198.jpg

Fig. 1: Intake manifold installation-4.3L engines (click over image for zoom)


zjlimited_200.jpg

Fig. 2: Intake manifold bolt tightening sequence-1996-98 4.3L engines

Install the bolts and tighten in sequence and in 3 steps as follows:

  1. First step to 26 inch lbs. (3 Nm).
  2. Second step to 106 inch lbs. (12 Nm).
  3. Final step to 11 ft. lbs. (15 Nm).

Hope this helps (remember to rate this answer). Good luck.

Dec 08, 2010 | 1998 Chevrolet Blazer

1 Answer

Diagram on how to remove and install a spider fuel injector core on a 1994 chevy blazer s10


Here is the removal procedure, and the procedure is the same for both the V-6 and the V-8 Vortec engines. Also, be certain to put engine oil on the "o"-ring seal for the fuel injector assembly before installing the upper intake. Let me know if you require any further assistance.

REMOVAL:

1. Disconnect the battery negative cable assembly from the battery negative terminal.

2. Remove the air cleaner assembly.

3. Remove the wiring harness connectors and the brackets and move aside.

4. Remove the throttle cable and the bracket from the upper intake manifold.

5. Remove the cruise control cable, (if equipped).

6. Remove the fuel lines from the intake to the rear of the block.

7. Remove the ignition coil and the bracket.

8. Remove the upper intake manifold.

INSTALLATION:

1. Install the upper intake manifold gasket.

2. Install the upper intake manifold. Use care not to pinch the injector lines between the upper and lower intake manifolds.

3. Install the upper intake manifold bolts. Note the marks made at disassembly for proper stud location. Install the two corner studs first in order to help align the two halves. NOTE: Other than the two torque passes listed below, the OE Manufacturer did NOT address or supply a bolt tightening sequence for the upper Intake Manifold for this model year, or other model years where this 2 piece manifold setup is used. A "Play It Safe" final tightening sequence would be to tighten from the center most bolts to the outer most bolts.

4. Tighten the bolts in two steps: a. Tighten the bolts on the first sequence to 5 Nm (44 inch lbs.). b. Tighten the bolts on the final sequence to 10 Nm (88 inch lbs.).

5. Install the purge solenoid and bracket.

6. Install the ignition coil and bracket.

7. Install the PCV hose et the upper intake manifold.

8. Install the fuel lines from the intake at the rear of the block.

9. Install the cruise control cable (if equipped).

10. Install the throttle cable and bracket from the upper intake manifold.

11. Install the wiring harness connectors and brackets.

12. Install the air cleaner assembly.

13. Connect the battery negative cable assembly to the battery negative terminal. - Tighten the bolt to 15 Nm (11 ft. lbs.).


2640099.jpg

8a054ef.jpg

Oct 22, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

Need the torque specs for the upper intake bults on a 2002 chrysler sebring conv. 2.7L


4022caa.jpg

Fig. Intake manifold bolt torque sequence 2.7L engine

Upper intake manifold with a new gasket on the lower intake manifold and torque the bolts, in sequence, to: 105 inch lbs. (12 Nm)

Hope helps (remember to rate this answer). Good job.

Oct 11, 2010 | 2002 Chrysler Sebring

2 Answers

Need torque specs for a 2001 jeep cherokee intake manifold


Intake manifold using new gaskets. Torque the bolts, in sequence, to 105 inch lbs. (12 Nm)...

6a7ecad.jpg

Fig. Intake manifold torque sequence-3.7 & 4.7L engines


Hope this help (remember comment and rated this).

May 07, 2010 | 2001 Jeep Cherokee

1 Answer

Any gm techs out there that would know the torque


Start at the middle and work your way criss crossing outward using 35 foot pounds of torque. All intakes use the same technique. Never start at the ends, alsays the middle section working your way out

Feb 04, 2010 | 2001 Chevrolet Blazer

1 Answer

How to change an intake manifold gasket on a 2001 blazer s10


I suggest buying a haynes or chilton manual for your truck it will give you step by step instructions.

Sep 28, 2009 | 2001 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

681 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...