Question about 1993 Honda Accord

1 Answer

1993honda runs on start, but dies in the on position

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 104 Answers

It sounds like a bad ignition switch easy way to check is follow the relay back with a test light and see if your not getting power in the on position thats your concern (ingnition switch) hope i could be of some help...

Posted on May 24, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Windstar runs then dies then starts back up


At best, this would really be hard to find, since you can drive it hours before it happens. You could start by pulling all the fuses one at a time check them and put them back in. This gets rid of corrosion contact problems. You can also do the to all the plugs. Sounds like you have a heat up problem. Some thing in the electrical system is getting hot and loosing contact. Things that would kill the engine would be , the ignition switch, the map sensor, the mass air flow sensor, And the engine control module. Parts inside of these can heat up enough to loose contact. Your's is going to be a hard one to find. Until the part completely dies.

Sep 08, 2014 | 2000 Ford Windstar

1 Answer

Starts but wont run after ignition switch is returned to the run position from the start position.


The problem is that when you have the switch in the START position, you are getting power to the ignition system, but not when in the RUN position. Most likely causes are a bad ignition switch, a faulty aftermarket alarm system [if it has one] or a bad ballest resistor wire going to the ignition coil's + terminal. You need to break out your test light and start checking to see where the fault lies.

Jul 14, 2014 | 1981 Ford F 150

1 Answer

1993honda accord wont start when its cold outside


Possible causes: ice in gas filter clogging gas flow, preheater for carburator or fuel mix not working

Jan 21, 2013 | Cars & Trucks

1 Answer

Car died while stopped at stop sign jump started got home replaced alternator starts with jump then dies removed pos. term. with key off strong spark...


While the car is running, disconnect Positive terminal of battery, if car continues running, alternator is good, you should replace battery,if it dies alternator is bad. Hope this helps

Jul 13, 2011 | 1999 Chevrolet Lumina

1 Answer

On frist attemp to start car, cranks then dies after few seconds ckd fuel rail , had no pressure , replaced fuel pump regulator , no help !


do you hear the fuel pump turn on when you turn the key to the run position? If not the check the fuel pump relay.

If the car will start and run for a few seconds then die, It may well be the crank position sensor.

Nov 01, 2010 | 1990 Buick Regal

1 Answer

Starts and dies as soon as it starts running


could be numerous issues.

First check your intake air filter - replace if very dirty and try again.

try going to an auto store where they offer free vehicle diagnostic scans. Get the codes and the problem parts.

It could be one of many sensors including O2 sensor, crankshaft position sensor, camshaft position sensor

Most of those are fairly easy to replace on this vehicle

Let me know what you find

Nov 21, 2009 | 1999 Jeep Cherokee

1 Answer

1991 blazer 4.3 ,starts but dies


check FUSE LINKS as there is a run fuse link od GM products

Jan 14, 2009 | 1991 Chevrolet S-10 Blazer

1 Answer

Car starts, then dies within 2or3 seconds.


Try this start eng and before it dies disconnect the starter solenoid, and hold the ignition in the crank position like you are starting it, if the engine remains running replace the ignition switch, they come apart and cause this issue

Sep 20, 2008 | 1996 Lincoln Mark VIII

Not finding what you are looking for?
1993 Honda Accord Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...