Question about Mazda B2600

Open Question

Who do accurately align gear timing on mazda b2500 diesel engine

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
Ad
  • 6 Answers

SOURCE: B 2500 diesel pickup hard start from cold

Hey mate,

I have a Mazda B2200 from 1985, which has the same R2 diesel motor, and I had this same problem, which was exacerbated by the cold of winter....even here in a mild Melbourne.

Each time you turn the ignition on, the QSS (Quick Start System) powers up the glow plugs for about three seconds. This recycles again about three times, then.....nothing. The QSS reckons that you ought to have the bugger running by now!

In my desperation, I located the cable to the four glow plugs, and ran a second wire from the battery (+) via a push-button switch which I installed on the dash. This is my glow-plug BOOST circuit.

Now, when I want to start from c-c-c-cold, I push the button (with the ignition on) for about ten or fifteen seconds, which gives the glow plugs a goodly time to heat up the combustion chamber, and when I hit the starter, she usually fires up with a rattle, and a cloud of grey exhaust smoke.

BINGO!

(Of course, once the motor has warmed up, there is no need to use this BOOST circuit, for the combustion chambers are already hot enough to detonate the injected fuel.)

Have a go at it, as I know that it works!

John.

Posted on May 28, 2009

emissionwiz
  • 79186 Answers

SOURCE: Need fuse diagram for mazda b2500

go to the link below and choose the 1998 ford ranger as the truck, they are the same, then follow the link to ford site and download the 1998 ranger owners manual, the fuse diagrams are in there
http://www.edmunds.com/ownership/howto/articles/120189/article.html

Posted on Sep 16, 2009

steve_e_uk
  • 1675 Answers

SOURCE: i need head bolt torque for mazda b2500 wl engine

e94d3fc.png03cad01.png
hope this helps...please vote thanks

Posted on May 31, 2010

duane_wong
  • 6826 Answers

SOURCE: timing belt markings mazda B2500 1998

Timing Belt, Sprockets & Front Cover Removal & Installation Timing belt To Remove:

  1. Disconnect the negative battery cable.
  2. Remove the exhaust side spark plugs, outer timing belt cover, and crankshaft pulley.
  3. Turn the crankshaft until the number one piston is at top dead center (TDC). CAUTION
    The camshaft belt tensioner tool (303-097) can be damaged when trying to relieve belt tension if you attempt to remove the belt without first loosening both the timing belt tensioner adjusting bolt and the spring pivot bolt.
  4. Loosen the timing belt spring pivot bolt, but do not remove it at this point in the procedure.
  5. Loosen the adjusting bolt slowly and release the spring tension.
  6. Turn the tensioner with the camshaft belt tensioner tool (303-097), against the spring pressure, clockwise to the farthest position.
  7. While holding it in this position, tighten the adjusting bolt to hold the tensioner away from the belt.
  8. Remove the timing belt.
To Install:
  1. Be certain that on piston number one, the crankshaft is at TDC with the crankshaft keyway pointing straight up and the circle on the crankshaft sprocket lined up with the notch on the engine front cover.
  2. Line up the timing marks.
  3. Install the timing belt over the crankshaft sprocket going counterclockwise over the oil pump sprocket and over the camshaft sprocket.
  4. Loosen the bolt allowing the tensioner pulley to press against the timing belt. NOTE: The timing belt tensioner should not be tightened or the belt tension will not be evenly distributed over the whole belt.
  5. Turn the crankshaft two revolutions clockwise. Next, slowly bring the crank to the number one position firing position with the keyway on the crank facing up. The dot on the crankshaft gear is lined up with the notch on the front cover.
  6. Check the timing mark alignment again. If necessary, repeat the procedure.
  7. Tighten the bolts. Torque the pivot bolt to 30-40 ft-lb (40-55 Nm). Torque the adjustment/locking bolt to 26-33 ft-lb (35-45 Nm).
  8. Install the crankshaft pulley and tighten the bolt. Torque to 93-121 ft-lb (125-165 Nm).
  9. Install the outer timing belt cover and tighten the bolt. Torque to 70-106 in-lb (8-12 Nm).
  10. Install the exhaust side spark plugs.
Sprockets To Remove:
  1. Remove the timing belt.
  2. Install the camshaft sprocket holding/removing tool (303-098) onto the sprocket.
  3. Remove the camshaft sprocket.
To Install:
  1. Place the key and camshaft sprocket on the shaft.
  2. Install the camshaft sprocket holding/removing tool (303-098) onto the camshaft sprocket and tighten the bolt. Torque to 52-70 ft-lb (70-95 Nm).
  3. Remove the tool then install the timing belt.
Outer Cover To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the fan shroud.
  4. Loosen the bolts on the water pump pulley, but do not remove them at this point in the procedure.
  5. Remove the drive belt, the water pump pulley, and the fan and clutch assembly.
  6. Recover the refrigerant from the A/C system.
  7. Disconnect the A/C wiring connector.
  8. Remove the A/C compressor from the mounting bracket then remove the A/C mounting bracket with the power steering pump still attached.
  9. Remove the outer timing belt cover.
To Install:
  1. Install the outer timing belt cover. Torque to 70-106 in-lb (8-12 Nm).
  2. Install the A/C mounting bracket with the power steering pump still attached. Torque the M10 bolts and stud to 35 ft-lb (48 Nm) and torque the M8 bolt to 18 ft-lb (25 Nm).
  3. Install the A/C compressor to the mounting bracket. Torque to 16-20 ft-lb (21-28 Nm).
  4. Connect the A/C wiring connector.
  5. Refill the refrigerant into the A/C system.
  6. Install the fan and clutch assembly, the water pump pulley, and the drive belt.
  7. Tighten the bolts on the water pump pulley. Torque to 13-17 ft-lb (17-23 Nm).
  8. Install the fan shroud. Torque to 54-70 in-lb (6-8 Nm).
  9. Connect the negative battery cable.
  10. Start the engine. Check for leaks and repair as necessary.
Inner Cover To Remove:
  1. Loosen oil pump sprocket bolt.
  2. Remove timing belt, timing belt tensioner, oil pump sprocket, and crankshaft pulley.
  3. Remove inner timing belt cover.
To Install:
  1. Install inner timing belt cover.
  2. Install crankshaft pulley. Torque to 93-121 ft-lb (125-165 Nm).
  3. Install the oil pump sprocket.
  4. Install the timing belt tensioner. Torque the pivot bolt to 30-40 ft-lb (40-55 Nm). Torque the adjustment/locking bolt to 26-33 ft-lb (35-45 Nm).
  5. Install the timing belt.
  6. Tighten the oil pump sprocket bolt. Torque to 30-40 ft-lb (40-55 Nm).
  7. Torque the camshaft bolt to 52-70 ft-lb (70-95 Nm).

Posted on Jul 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wh does 1st gear jump out on accelerator release ?


There are a few things to check. Engine and transmission mounts replace any broken or perished . 1st gear selector shaft has a indent ball and spring to locate the shaft when in gear, check the spring is not broken. The gear box bearings may be worn giving the drive shaft to much end play. also check gear shift linkage is not worn.

Aug 23, 2014 | 1999 Mazda B2500

1 Answer

I have a Mazda/Ford B2500 diesel 4x4double cab 96/97model . Would later model Diesel engine say 1999 to 2005 be inter changeable with existing gear box. That is remove old engine and put another engine in...


As the later engine would have a higher torque rating I would be looking at clutch pressure plate size to determine if the whole unit would be a best course of action. If you have both later engine and gear box assembly then I would fit it as a unit then I would know that the gear box would handle the extra torque from the engine.

Sep 07, 2013 | Cars & Trucks

1 Answer

My 1999 mazda b2500 misfiring on cylinders number 1&2 diesel injectors fine . What could be the problem


Diesel ?? common rail or injector pump ,either way firstly i would suspect the head gasket as it sounds like its burnt through between cylinders one and two .This is the most connon fault with any engine

May 18, 2013 | Cars & Trucks

1 Answer

Help with torque setting for mazda b2500 wl diesel engine


What is de torque for wl 2500 mazda main bering. Thanks

Mar 25, 2013 | Cars & Trucks

1 Answer

On a 2001 mazda bravo turbo disel when do I have to change the timming belet it's done 176000 ks


Hi there,

Without knowing which diesel engine you have, I'll have to guess that you have a 2.5L (B2500) - Note: the more detailed information you give us, the more accurate our answers will be :-)

As a general rule, cambelts (with tensioner assembly & seals) have a limited life and should always be replaced every 100,000km, or sometimes earlier depending on manufacturer. The reasoning behind this is that most engines will suffer major internal damage if the cambelt snaps (this is what is meant by 'Interference' engines). As the engine has to be opened up to carry out this service, it can be a costly maintenance. For this reason, it is also common to replace the waterpump at the same time (to avoid having to open up the engine again) as waterpumps have been known to fail beyond 100,000km.

The good news....if you DO have a 2.5L (B2500) engine, then this engine is a NON interference engine - which means, if the cambelt did snap, your engine would not suffer any internal damage, compared to interference engines.

Hope this helps.....


"If this has helped you in any way, please rate this solution"

May 07, 2011 | Mazda B2200 Cars & Trucks

1 Answer

At what speeds should you shift gears in a 1999 Mazda B2500?


Shifting is determined more accurately by rpm's not speed. If you have a tach in the car, run the motor up to where you feel performance "flatten out" Regard that as your max rpm (for all gears) shift as needed about 500-700 below that number and all will be fine. (example: if motor flattens out at 3500 rpm, you should be shifting at 3,000 rpm or if not accelerating hard, at 2,800.) Going above the limit (shifting later) puts you outside the useful torque range and is not helpful.

Dec 14, 2009 | 1999 Mazda Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

79123 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...