Question about Nissan 240SX

1 Answer

92 nissan 240sx wont run after 2500- 3000 rpms changed cap and rotor new wires w/ plugs starts right after dies timing is also good

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 324 Answers

A weak coil could cause that problem
could also be an issue with the ECM / PCM
low fuel pressure caused by a weak fuel pump, clogged filter or dirty injector(s)

if you haven't tried this already then you should. get some QUALITY fuel system cleaner / injector cleaner, and follow the directions.

hope this helps.

Posted on May 24, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Injector has constant power


Sounds like timing. OR it needs a distributor cap and rotor. Pull the cap and inspect the inside contacts. If you see them a "white powder" looking substance coating where there should be brass i the top of that cap, simply replace the cap and rotor button and thank your lucky stars. lol.
(Go ahead and give it new spark plugs, while your there. imo)
If not, it may have jumped time. Call a mechanic.....

Dec 15, 2013 | 1990 Nissan 240SX

2 Answers

Car wont start


check timing and fuel delivery.

Mar 08, 2013 | 1995 Nissan Altima

1 Answer

Ka24de bogs at 3000 rpms and wont go any higher


why did you change mass air flow sensor ? do you have coil packs, any codes stored in ECM ? something is telling it to go full lean ! ? another sensor, OXYGEN SENSOR, MAP SENSOR ? aftermarket MAF sensors are garbage, you might need a stock , OEM , MAF !!!!!!!!! I would , my 87 buick gn boged when I replaced my MAF , I got a new OEM , STOCK , MAF, exact replacement, it ran wonderful !!!! again !

Feb 10, 2013 | 1991 Nissan 240SX

1 Answer

1998 Altima dies wile driving then wont start back up


Have you checked your "knock sensor" or cam sensor? It tracks cam and or crank movement for timing.

Jul 26, 2012 | 1998 Nissan Altima

1 Answer

Hello i have a 92 nissan 240sx just got car started after installing head gasket car ran great all day other than a small surge under mild throttle, later that night when i went to start the car now i have...


When replacing head gasket you had to disconnect and move spark plug wires and coil wire.Sounds to me if it ran for a little while then died out look for a burned wire by exhaust manifold.Something must of shorted out.Thats why it ran a little while and died.

Feb 10, 2011 | 1992 Nissan 240SX Fastback

2 Answers

I have a 91 240sx that is very hard to start when cold and you cant touch throttle or it will die


1) Does is crank / spin properly?. Good battery and connections?
2) Does it have high mileage? Check compression.
3) Fuel injected? Maybe cold start valve not working properly.

My best guess is check fuel delivery. Clean? filters, lines, good fuel pump?
Also ignition could be faulty. Good plugs, wires, cap and rotor?

Good luck!

Mar 26, 2010 | 1990 Nissan 240SX

1 Answer

Had work done on my car (36K miles on the car): oil change, new plugs, new plug wires, new dist cap, new dist rotor, fuel filter, pvc valve, and brake work. Now it runs like ****. rough running and exhaust...


Sounds like a fuel mix problem possibly the oxygen sensor. If it ran like this immediately after the new plugs, I would check to make sure all the plug wires are on the right plugs and secure. Good luck!

Mar 10, 2010 | 1990 Nissan Maxima

2 Answers

92 C1500 Chevy wont start. Changed plugs, wires, distributor, rotor and fule filter. Pump runs when key is turned on. Poured gas to the distributor and starts up and runs fine. but jerks ar high rpms...


So you threw parts at it. No harm intended. Should have started with the adding gas part first. You know the filter is new and it does run! Are the fuel pump amps correct,pump mech bound,no fuel volume, pressure regulator work correctly? Does the pump run in start mode or time out? Now the harder stuff. What does the spark and timing look like,What is the computer seeing and then what command is it sending?

Sep 29, 2009 | 1992 Chevrolet C1500

1 Answer

92 nissan wire patern


I have a 92 Nissan congrats they are awesome cars. Me and my friend changed the rotor and cap along with the spark plugs on mine. If you lost the wire pattern I would recommend going to auto store and looking it up in the nissan car manual.
Good Luck
Proteus

May 21, 2009 | 1992 Nissan Sentra 4 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...